On 24/05/2016 14:28, Peng Fan wrote:
> In 'commit d584c68ce0f5bf2f430ccfb2ba00bd506206fb91',
> ar8031 is changed to use ar8035_config. ar8035_config
> actually does the same thing as mx6_rgmii_rework, so
> drop mx6_rgmii_rework and board_phy_config.
>
> Signed-off-by: Peng Fan <van.free...@gmail.com>
> Cc: Fabio Estevam <fabio.este...@nxp.com>
> Cc: Stefano Babic <sba...@denx.de>
> ---
> board/freescale/mx6qsabreauto/mx6qsabreauto.c | 33
> ---------------------------
> 1 file changed, 33 deletions(-)
>
> diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
> b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
> index 0712f08..d63a979 100644
> --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
> +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
> @@ -321,39 +321,6 @@ static void setup_gpmi_nand(void)
> }
> #endif
>
> -int mx6_rgmii_rework(struct phy_device *phydev)
> -{
> - unsigned short val;
> -
> - /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
> - phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
> - phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
> - phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
> -
> - val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
> - val &= 0xffe3;
> - val |= 0x18;
> - phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
> -
> - /* introduce tx clock delay */
> - phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
> - val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
> - val |= 0x0100;
> - phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
> -
> - return 0;
> -}
> -
> -int board_phy_config(struct phy_device *phydev)
> -{
> - mx6_rgmii_rework(phydev);
> -
> - if (phydev->drv->config)
> - phydev->drv->config(phydev);
> -
> - return 0;
> -}
> -
> static void setup_fec(void)
> {
> if (is_mx6dqp()) {
>
Acked-by: Stefano Babic <sba...@denx.de>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
