To enable DM on MPC85xx, we need pre-relocation malloc, which is implemented in this patch.
We also make sure that the IVORs are always 4-aligned on e500 to prevent alignment exceptions caused by code changes in start.S. Signed-off-by: Mario Six <mario....@gdsys.cc> Cc: York Sun <york....@nxp.com> Cc: Simon Glass <s...@chromium.org> --- v2: - Correct IVOR alignment and remove nop hack - Add sanity check for length of malloc area arch/powerpc/cpu/mpc85xx/cpu_init_early.c | 8 -------- arch/powerpc/cpu/mpc85xx/start.S | 28 ++++++++++++++++++++++++++++ include/ppc_asm.tmpl | 3 +++ 3 files changed, 31 insertions(+), 8 deletions(-) diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init_early.c b/arch/powerpc/cpu/mpc85xx/cpu_init_early.c index 235a635..e6e1688 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init_early.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init_early.c @@ -82,7 +82,6 @@ void setup_ifc(void) void cpu_init_early_f(void *fdt) { u32 mas0, mas1, mas2, mas3, mas7; - int i; #ifdef CONFIG_SYS_FSL_ERRATUM_P1010_A003549 ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); #endif @@ -95,13 +94,6 @@ void cpu_init_early_f(void *fdt) /* Pointer is writable since we allocated a register for it */ gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET); - /* - * Clear initial global data - * we don't use memset so we can share this code with NAND_SPL - */ - for (i = 0; i < sizeof(gd_t); i++) - ((char *)gd)[i] = 0; - #ifdef CONFIG_QEMU_E500 /* * CONFIG_SYS_CCSRBAR_PHYS below may use gd->fdt_blob on ePAPR systems, diff --git a/arch/powerpc/cpu/mpc85xx/start.S b/arch/powerpc/cpu/mpc85xx/start.S index d867e2a..cc4cf5f 100644 --- a/arch/powerpc/cpu/mpc85xx/start.S +++ b/arch/powerpc/cpu/mpc85xx/start.S @@ -1152,6 +1152,34 @@ _start_cont: /* Setup the stack in initial RAM,could be L2-as-SRAM or L1 dcache*/ lis r3,(CONFIG_SYS_INIT_RAM_ADDR)@h ori r3,r3,((CONFIG_SYS_INIT_SP_OFFSET-16)&~0xf)@l /* Align to 16 */ + +#ifdef CONFIG_SYS_MALLOC_F_LEN + +#if CONFIG_SYS_MALLOC_F_LEN + GENERATED_GBL_DATA_SIZE > CONFIG_SYS_INIT_RAM_SIZE +#error "CONFIG_SYS_MALLOC_F_LEN too large to fit into initial RAM." +#endif + + /* Leave 16+ byte for back chain termination and NULL return address */ + subi r3,r3,((CONFIG_SYS_MALLOC_F_LEN+16+15)&~0xf) + + /* End of RAM */ + lis r4,(CONFIG_SYS_INIT_RAM_ADDR)@h + ori r4,r4,(CONFIG_SYS_INIT_RAM_SIZE)@l + + li r0,0 + +1: subi r4,r4,4 + stw r0,0(r4) + cmplw r4,r3 + bne 1b + + lis r4,(CONFIG_SYS_INIT_RAM_ADDR)@h + ori r4,r4,(CONFIG_SYS_GBL_DATA_OFFSET)@l + + addi r3,r3,16 /* Pre-relocation malloc area */ + stw r3,GD_MALLOC_BASE(r4) + subi r3,r3,16 +#endif li r0,0 stw r0,0(r3) /* Terminate Back Chain */ stw r0,+4(r3) /* NULL return address. */ diff --git a/include/ppc_asm.tmpl b/include/ppc_asm.tmpl index ba166eb..379c493 100644 --- a/include/ppc_asm.tmpl +++ b/include/ppc_asm.tmpl @@ -263,12 +263,14 @@ b transfer_to_handler #define STD_EXCEPTION(n, label, hdlr) \ +.align 4; \ label: \ EXCEPTION_PROLOG(SRR0, SRR1); \ addi r3,r1,STACK_FRAME_OVERHEAD; \ EXC_XFER_TEMPLATE(n, label, hdlr, MSR_KERNEL, NOCOPY) \ #define CRIT_EXCEPTION(n, label, hdlr) \ +.align 4; \ label: \ EXCEPTION_PROLOG(CSRR0, CSRR1); \ addi r3,r1,STACK_FRAME_OVERHEAD; \ @@ -276,6 +278,7 @@ label: \ MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE), NOCOPY) \ #define MCK_EXCEPTION(n, label, hdlr) \ +.align 4; \ label: \ EXCEPTION_PROLOG(MCSRR0, MCSRR1); \ addi r3,r1,STACK_FRAME_OVERHEAD; \ -- 2.7.0.GIT _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot