Hi Qianyu, > -----Original Message----- > From: U-Boot [mailto:u-boot-boun...@lists.denx.de] On Behalf Of Qianyu > Gong > Sent: Thursday, January 14, 2016 9:57 AM > To: Scott Wood <o...@buserror.net>; u-boot@lists.denx.de > Cc: b48...@freescale.com; Mingkai Hu <mingkai...@nxp.com>; > wenbin.s...@freescale.com > Subject: Re: [U-Boot] [Patch V3 3/3] armv8/ls1043aqds: add QSPI boot support > > > > -----Original Message----- > > From: Scott Wood [mailto:o...@buserror.net] > > Sent: Thursday, January 14, 2016 8:21 AM > > To: Qianyu Gong <qianyu.g...@nxp.com>; u-boot@lists.denx.de > > Cc: b07...@freescale.com; b48...@freescale.com; > > wenbin.s...@freescale.com; Mingkai Hu <mingkai...@nxp.com> > > Subject: Re: [U-Boot] [Patch V3 3/3] armv8/ls1043aqds: add QSPI boot > > support > > > > On Tue, 2016-01-12 at 03:14 +0000, Qianyu Gong wrote: > > > > -----Original Message----- > > > > From: Scott Wood [mailto:o...@buserror.net] > > > > Sent: Tuesday, January 12, 2016 1:47 AM > > > > To: Qianyu Gong <qianyu.g...@nxp.com>; u-boot@lists.denx.de > > > > Cc: b07...@freescale.com; b48...@freescale.com; > > > > wenbin.s...@freescale.com; Mingkai Hu <mingkai...@nxp.com> > > > > Subject: Re: [U-Boot] [Patch V3 3/3] armv8/ls1043aqds: add QSPI > > > > boot support > > > > > > > > On Mon, 2016-01-11 at 10:17 +0800, Gong Qianyu wrote: > > > > > diff --git a/board/freescale/ls1043aqds/ls1043aqds.c > > > > > b/board/freescale/ls1043aqds/ls1043aqds.c > > > > > index d6696ca..770b79f 100644 > > > > > --- a/board/freescale/ls1043aqds/ls1043aqds.c > > > > > +++ b/board/freescale/ls1043aqds/ls1043aqds.c > > > > > @@ -43,15 +43,19 @@ enum { > > > > > > > > > > int checkboard(void) > > > > > { > > > > > +#ifndef CONFIG_QSPI_BOOT > > > > > char buf[64]; > > > > > #ifndef CONFIG_SD_BOOT > > > > > u8 sw; > > > > > #endif > > > > > +#endif > > > > > > > > > > puts("Board: LS1043AQDS, boot from "); > > > > > > > > > > #ifdef CONFIG_SD_BOOT > > > > > puts("SD\n"); > > > > > +#elif defined(CONFIG_QSPI_BOOT) > > > > > + puts("QSPI\n"); > > > > > #else > > > > > sw = QIXIS_READ(brdcfg[0]); > > > > > sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; @@ > -68,12 > > > > +72,15 > > > > > @@ int checkboard(void) > > > > > printf("invalid setting of SW%u\n", > QIXIS_LBMAP_SWITCH); > > > > #endif > > > > > > > > > > +#ifndef CONFIG_QSPI_BOOT > > > > > + /* For QSPI boot, here I2C is not ready yet. */ > > > > > printf("Sys ID: 0x%02x, Sys Ver: 0x%02x\n", > > > > > QIXIS_READ(id), QIXIS_READ(arch)); > > > > > > > > > > printf("FPGA: v%d (%s), build %d\n", > > > > > (int)QIXIS_READ(scver), qixis_read_tag(buf), > > > > > (int)qixis_read_minor()); > > > > > +#endif > > > >
It will be useful, if the above FPGA prints are available for QSPI boot as well. > > > > Why isn't i2c ready? How is DDR inited without it? > > > > > > > > -Scott > > > > > > Hi Scott, > > > > > > The calling sequence in U-Boot is : > > > checkboard() -> init_func_i2c() -> dram_init() > > > > > > So I2C is not ready in checkboard() but is ready for DDR initialization. > > > > Can you move the prints later in the boot sequence? > > > > In any case, the relevant variable is whether qixis uses i2c, not > > whether you're booting from qspi (even if they are correlated). > > > > -Scott > > Yes. Only with QSPI it needs I2C to access QIXIS. > But if defining CONFIG_DISPLAY_BOARDINFO_LATE, the print layout will look > really uncomfortable.. So we just comment out the FPGA prints for QSPI boot. > > Regards, > Qianyu Thanks Calvin _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
