Joe, York, On Tue, Jan 12, 2016 at 2:41 PM, Bin Meng <bmeng...@gmail.com> wrote: > This series adds driver model ethernet support to the Freescale > TSEC ethernet driver and convert ls1021atwr board to use it. > > Enable the support in the ls1021atwr_nor_defconfig and > ls1021atwr_nor_lpuart_defconfig configurations. > > > Bin Meng (17): > powerpc: bsc9132qds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET > powerpc: c29xpcie: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET > powerpc: mpc8572ds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET > powerpc: mpc8548cds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET > powerpc: p1010rdb: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET > arm: ls1021atwr: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET > net: tsec: fsl_mdio: Fix several cosmetic issues > net: tsec: Move rx_idx and tx_idx to struct tsec_private > net: tsec: Move rxbd and txbd to struct tsec_private > net: tsec: Adjust orders to avoid forward declaration of tsec_send() > net: tsec: Use tsec_private pointer as the parameter for internal > routines > doc: dt-bindings: Describe Freescale TSEC ethernet controller > net: tsec: Add driver model ethernet support > net: tsec: Use priv->tbiaddr to initialize TBI PHY address > arm: ls102xa: Rewrite the logic of ft_fixup_enet_phy_connect_type() > arm: ls1021atwr: Disable CONFIG_E1000 temporarily > arm: ls1021atwr: Convert to use driver model TSEC driver > > arch/arm/cpu/armv7/ls102xa/cpu.c | 2 +- > arch/arm/cpu/armv7/ls102xa/fdt.c | 26 +- > arch/arm/dts/ls1021a-twr.dts | 20 + > arch/arm/dts/ls1021a.dtsi | 18 +- > board/freescale/bsc9132qds/bsc9132qds.c | 4 +- > board/freescale/c29xpcie/c29xpcie.c | 4 +- > board/freescale/ls1021atwr/ls1021atwr.c | 4 +- > board/freescale/mpc8548cds/mpc8548cds.c | 4 +- > board/freescale/mpc8572ds/mpc8572ds.c | 4 +- > board/freescale/p1010rdb/p1010rdb.c | 4 +- > configs/ls1021atwr_nor_defconfig | 3 +- > configs/ls1021atwr_nor_lpuart_defconfig | 3 +- > doc/device-tree-bindings/net/fsl-tsec-phy.txt | 64 +++ > drivers/net/fsl_mdio.c | 4 +- > drivers/net/tsec.c | 536 > ++++++++++++++++++-------- > include/configs/ls1021atwr.h | 4 + > include/fsl_mdio.h | 7 +- > include/tsec.h | 69 ++-- > 18 files changed, 546 insertions(+), 234 deletions(-) > create mode 100644 doc/device-tree-bindings/net/fsl-tsec-phy.txt >
I wonder if you can post some review comments if any before I spin a v2? Regards, Bin _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
