Hi Michal,
On 2015年12月15日 23:39, Michal Simek wrote:
On 15.12.2015 05:02, Thomas Chou wrote:
Hi Michal,
On 2015年12月14日 23:42, Michal Simek wrote:
On 14.12.2015 15:35, Thomas Chou wrote:
Hi Michal,
On 2015年12月11日 19:54, Michal Simek wrote:
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <michal.si...@xilinx.com>
---
board/xilinx/microblaze-generic/xparameters.h | 4 ----
configs/microblaze-generic_defconfig | 1 +
drivers/serial/Kconfig | 7 +++++++
include/configs/microblaze-generic.h | 7 +------
4 files changed, 9 insertions(+), 10 deletions(-)
diff --git a/board/xilinx/microblaze-generic/xparameters.h
b/board/xilinx/microblaze-generic/xparameters.h
index 8ba146cb88db..11b3c9a4846e 100644
--- a/board/xilinx/microblaze-generic/xparameters.h
+++ b/board/xilinx/microblaze-generic/xparameters.h
@@ -28,10 +28,6 @@
#define XILINX_TIMER_BASEADDR 0x41c00000
#define XILINX_TIMER_IRQ 0
-/* Uart pheriphery is RS232_Uart */
-#define XILINX_UARTLITE_BASEADDR 0x40600000
-#define XILINX_UARTLITE_BAUDRATE 115200
-
/* IIC pheriphery is IIC_EEPROM */
#define XILINX_IIC_0_BASEADDR 0x40800000
#define XILINX_IIC_0_FREQ 100000
diff --git a/configs/microblaze-generic_defconfig
b/configs/microblaze-generic_defconfig
index 5df080b6a87c..9a7bb915466f 100644
--- a/configs/microblaze-generic_defconfig
+++ b/configs/microblaze-generic_defconfig
@@ -9,3 +9,4 @@ CONFIG_CMD_GPIO=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_SPL_OF_CONTROL=y
CONFIG_OF_EMBED=y
+CONFIG_XILINX_UARTLITE=y
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index f1e221799b81..ddf49ba9cef3 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -230,4 +230,11 @@ config UNIPHIER_SERIAL
If you have a UniPhier based board and want to use the on-chip
serial ports, say Y to this option. If unsure, say N.
+config XILINX_UARTLITE
+ bool "Xilinx Uarlite support"
+ depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
+ help
+ If you have a Xilinx based board and want to use the uartlite
+ serial ports, say Y to this option. If unsure, say N.
+
endmenu
Kconfig should be with the driver 1/3. Others are boards related.
It can be. Adding Kconfig fragment can be separate patch out of move to
DM. There is no connection too.
My intention was to show all related changes which are done by this one
step.
Please also make sure the patch series are bisectable.
I am not aware about anything what would caused that this series is not
bisectable. Do you see something like that?
No. Sorry. I didn't find DM and DM_serial in the microblaze repo at
first. Then I found them in the patches earlier.
Best regards,
Thomas
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
