[U-Boot] [PATCH 14/14] arm: mvebu: Make serdes setup on Armada XP less noisy

[Stefan Roese]

Change some of the PEX configuration output lines from always output to
only ouput upon specific debug enabling.

This changes the SPL output from:

U-Boot SPL 2016.01-rc2-00037-g9353a7f (Dec 10 2015 - 10:27:42)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
Update Device ID PEX0782611ab
Update Device ID PEX1782611ab
Update Device ID PEX2782611ab
Update Device ID PEX3782611ab
Update Device ID PEX8782611ab
Update PEX Device ID 0x78260
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully

to:

U-Boot SPL 2016.01-rc2-00037-g9353a7f-dirty (Dec 10 2015 - 10:32:04)
High speed PHY - Version: 2.1.5 (COM-PHY-V20)
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.7.4
DDR3 Training Sequence - Ended Successfully

Resulting in a little faster bootup time.

Signed-off-by: Stefan Roese <s...@denx.de>
Cc: Luka Perkov <luka.per...@sartura.hr>
---
 arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c 
b/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c
index 9762971..bfa7f13 100644
--- a/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c
+++ b/arch/arm/mach-mvebu/serdes/axp/high_speed_env_lib.c
@@ -1376,19 +1376,19 @@ int serdes_phy_config(void)
                                                 pex_if, 
PEX_DEVICE_AND_VENDOR_ID));
                        devId &= 0xFFFF;
                        devId |= ((ctrl_mode << 16) & 0xffff0000);
-                       DEBUG_INIT_S("Update Device ID PEX");
-                       DEBUG_INIT_D(pex_if, 1);
-                       DEBUG_INIT_D(devId, 8);
-                       DEBUG_INIT_S("\n");
+                       DEBUG_INIT_FULL_S("Update Device ID PEX");
+                       DEBUG_INIT_FULL_D(pex_if, 1);
+                       DEBUG_INIT_FULL_D(devId, 8);
+                       DEBUG_INIT_FULL_S("\n");
                        reg_write(PEX_CFG_DIRECT_ACCESS
                                  (pex_if, PEX_DEVICE_AND_VENDOR_ID), devId);
                        if ((pex_if < 8) &&
                            (info->pex_mode[pex_unit] == PEX_BUS_MODE_X4))
                                pex_if += 3;
                }
-               DEBUG_INIT_S("Update PEX Device ID 0x");
-               DEBUG_INIT_D(ctrl_mode, 4);
-               DEBUG_INIT_S("0\n");
+               DEBUG_INIT_FULL_S("Update PEX Device ID 0x");
+               DEBUG_INIT_FULL_D(ctrl_mode, 4);
+               DEBUG_INIT_FULL_S("0\n");
        }
        tmp = reg_read(PEX_DBG_STATUS_REG(0));
        DEBUG_RD_REG(PEX_DBG_STATUS_REG(0), tmp);
-- 
2.6.4

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot