Hi Heiko, Thank you very much for your review.
> -----Original Message----- > From: Heiko Schocher [mailto:h...@denx.de] > Sent: 2015年12月9日 13:32 > To: Yang, Wenyou <wenyou.y...@atmel.com> > Cc: U-Boot Mailing List <u-boot@lists.denx.de> > Subject: Re: [U-Boot] [PATCH 0/3] ARM: at91: add PMC_PLLICPR init function > > Hello Wenyou, > > Am 09.12.2015 um 05:36 schrieb Wenyou Yang: > > To reduce the duplicated code, add PLLICPR init function, use the > > function to clean up the PMC_PLLICPR directly writing code. > > > > It is based on the following patch set. > > [PATCH 0/5] ARM: at91: improve peripheral and system clock handle > functions > > [PATCH 0/4] ARM: at91: add UTMI PLL handle functions > > [PATCH 0/3] ARM: at91: add PLLB handle functions > > > > > > Wenyou Yang (3): > > ARM: at91: clock: add PMC_PLLICPR init function > > ARM: at91: clean up the PMC_PLLICPR init code > > board: atmel: clean up the PMC_PLLICPR init code > > > > arch/arm/mach-at91/armv7/clock.c | 7 +++++++ > > arch/arm/mach-at91/include/mach/at91_pmc.h | 7 +++++++ > > arch/arm/mach-at91/include/mach/clk.h | 1 + > > arch/arm/mach-at91/spl_at91.c | 5 +---- > > board/atmel/sama5d3_xplained/sama5d3_xplained.c | 4 +--- > > board/atmel/sama5d3xek/sama5d3xek.c | 4 +--- > > board/atmel/sama5d4_xplained/sama5d4_xplained.c | 4 +--- > > board/atmel/sama5d4ek/sama5d4ek.c | 4 +--- > > 8 files changed, 20 insertions(+), 16 deletions(-) > > I applied all your at91 patches from: > > It is based on the following patch set. > [PATCH 0/5] ARM: at91: improve peripheral and system clock handle > functions > [PATCH 0/4] ARM: at91: add UTMI PLL handle functions > [PATCH 0/3] ARM: at91: add PLLB handle functions > > also this series, and compiled it for the smartweb board. This build fails: It is my fault, the build is not covered all Atmel boards. I will fix it in next version, thanks. > > LD spl/u-boot-spl > arch/arm/mach-at91/built-in.o: In function `board_init_f': > /home/hs/zug/u-boot/arch/arm/mach-at91/spl_at91.c:86: undefined reference to > `at91_pllicpr_init' > /home/hs/zug/u-boot/scripts/Makefile.spl:244: recipe for target > 'spl/u-boot-spl' > failed > make[2]: *** [spl/u-boot-spl] Error 1 > /home/hs/zug/u-boot/Makefile:1330: recipe for target 'spl/u-boot-spl' failed > make[1]: *** [spl/u-boot-spl] Error 2 > make[1]: Leaving directory '/work/hs/compile/u-boot/zug/smartweb' > Makefile:150: recipe for target 'sub-make' failed > make: *** [sub-make] Error 2 > make failed > pollux:u-boot hs [20151209] $ > > Please do a build for all at91 boards, before posting your patches again. > Also try > to have a look at the codesize ... the smartweb board have only 4k for the SPL > image... > > Thanks! > > bye, > Heiko > -- > DENX Software Engineering GmbH, Managing Director: Wolfgang Denk > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Best Regards, Wenyou Yang _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot