The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.

Signed-off-by: Marek Vasut <ma...@denx.de>
Cc: Joe Hershberger <joe.hershber...@ni.com>
Cc: Chin Liang See <cl...@altera.com>
Cc: Dinh Nguyen <dingu...@opensource.altera.com>
---
 board/ebv/socrates/socfpga.c       | 40 --------------------------------------
 include/configs/socfpga_socrates.h |  7 -------
 2 files changed, 47 deletions(-)

diff --git a/board/ebv/socrates/socfpga.c b/board/ebv/socrates/socfpga.c
index 0fbbc34..ccb1b4b 100644
--- a/board/ebv/socrates/socfpga.c
+++ b/board/ebv/socrates/socfpga.c
@@ -12,10 +12,6 @@
 #include <usb/dwc2_udc.h>
 #include <usb_mass_storage.h>
 
-#include <micrel.h>
-#include <netdev.h>
-#include <phy.h>
-
 DECLARE_GLOBAL_DATA_PTR;
 
 void s_init(void) {}
@@ -31,42 +27,6 @@ int board_init(void)
        return 0;
 }
 
-/*
- * PHY configuration
- */
-#ifdef CONFIG_PHY_MICREL_KSZ9021
-int board_phy_config(struct phy_device *phydev)
-{
-       int ret;
-       /*
-        * These skew settings for the KSZ9021 ethernet phy is required for 
ethernet
-        * to work reliably on most flavors of cyclone5 boards.
-        */
-       ret = ksz9021_phy_extended_write(phydev,
-                                        MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
-                                        0x0);
-       if (ret)
-               return ret;
-
-       ret = ksz9021_phy_extended_write(phydev,
-                                        MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
-                                        0x0);
-       if (ret)
-               return ret;
-
-       ret = ksz9021_phy_extended_write(phydev,
-                                        MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
-                                        0xf0f0);
-       if (ret)
-               return ret;
-
-       if (phydev->drv->config)
-               return phydev->drv->config(phydev);
-
-       return 0;
-}
-#endif
-
 #ifdef CONFIG_USB_GADGET
 struct dwc2_plat_otg_data socfpga_otg_data = {
        .regs_otg       = CONFIG_USB_DWC2_REG_ADDR,
diff --git a/include/configs/socfpga_socrates.h 
b/include/configs/socfpga_socrates.h
index 16a2a86..de8ced6 100644
--- a/include/configs/socfpga_socrates.h
+++ b/include/configs/socfpga_socrates.h
@@ -43,15 +43,8 @@
 
 /* Ethernet on SoC (EMAC) */
 #if defined(CONFIG_CMD_NET)
-
-/* PHY */
 #define CONFIG_PHY_MICREL
 #define CONFIG_PHY_MICREL_KSZ9021
-#define CONFIG_KSZ9021_CLK_SKEW_ENV    "micrel-ksz9021-clk-skew"
-#define CONFIG_KSZ9021_CLK_SKEW_VAL    0xf0f0
-#define CONFIG_KSZ9021_DATA_SKEW_ENV   "micrel-ksz9021-data-skew"
-#define CONFIG_KSZ9021_DATA_SKEW_VAL   0x0
-
 #endif
 
 #define CONFIG_ENV_IS_IN_MMC
-- 
2.1.4

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to