On 24/11/2015 11:23, maitysancha...@gmail.com wrote:
> Hello,
>
> Ping?
>
> Any further feedback? Is the patchset good to get accepted?
I'll pick it up
Best regards,
Stefano Babic
>
> Thanks.
>
> Regards,
> Sanchayan.
>
> On 15-11-12 11:47:35, Sanchayan Maity wrote:
>> Add board_usb_phy_mode function for detecting whether a port is
>> being used as host or client using a GPIO. On Colibri Vybrid we
>> provide GPIO 102 for this very same purpose.
>>
>> Signed-off-by: Sanchayan Maity <maitysancha...@gmail.com>
>> ---
>> Changes since v4:
>> No need to break after return.
>>
>> Changes since v3:
>> Return USB_INIT_DEVICE or USB_INIT_HOST after checking for
>> the GPIO state to account for the fact that the previous
>> logic breaks in case if the enum for USB mode were to ever
>> be changed.
>>
>> Add comments based on Stefan's feedback.
>>
>> Changes since v2:
>>
>> Instead of returning 0 from board_usb_phy_mode return it as
>> USB_INIT_HOST.
>>
>> Changes since v1:
>>
>> Move the GPIO request call to the board_init function as all
>> further calls to board_usb_phy_mode will actually result in the
>> gpio_request failing.
>> ---
>> board/toradex/colibri_vf/colibri_vf.c | 33 ++++++++++++++++++++++++++++++++-
>> 1 file changed, 32 insertions(+), 1 deletion(-)
>>
>> diff --git a/board/toradex/colibri_vf/colibri_vf.c
>> b/board/toradex/colibri_vf/colibri_vf.c
>> index a6d1c5b..c65ccb3 100644
>> --- a/board/toradex/colibri_vf/colibri_vf.c
>> +++ b/board/toradex/colibri_vf/colibri_vf.c
>> @@ -21,6 +21,7 @@
>> #include <i2c.h>
>> #include <g_dnl.h>
>> #include <asm/gpio.h>
>> +#include <usb.h>
>>
>> DECLARE_GLOBAL_DATA_PTR;
>>
>> @@ -34,6 +35,7 @@ DECLARE_GLOBAL_DATA_PTR;
>> PAD_CTL_DSE_50ohm | PAD_CTL_OBE_IBE_ENABLE)
>>
>> #define USB_PEN_GPIO 83
>> +#define USB_CDET_GPIO 102
>>
>> static struct ddrmc_cr_setting colibri_vf_cr_settings[] = {
>> /* levelling */
>> @@ -92,6 +94,7 @@ static struct ddrmc_cr_setting colibri_vf_cr_settings[] = {
>>
>> static const iomux_v3_cfg_t usb_pads[] = {
>> VF610_PAD_PTD4__GPIO_83,
>> + VF610_PAD_PTC29__GPIO_102,
>> };
>>
>> int dram_init(void)
>> @@ -280,7 +283,6 @@ static void setup_iomux_gpio(void)
>> VF610_PAD_PTB23__GPIO_93,
>> VF610_PAD_PTB26__GPIO_96,
>> VF610_PAD_PTB28__GPIO_98,
>> - VF610_PAD_PTC29__GPIO_102,
>> VF610_PAD_PTC30__GPIO_103,
>> VF610_PAD_PTA7__GPIO_134,
>> };
>> @@ -509,6 +511,10 @@ int board_init(void)
>>
>> setbits_le32(&scsc->sosc_ctr, SCSC_SOSC_CTR_SOSC_EN);
>>
>> +#ifdef CONFIG_USB_EHCI_VF
>> + gpio_request(USB_CDET_GPIO, "usb-cdet-gpio");
>> +#endif
>> +
>> return 0;
>> }
>>
>> @@ -554,4 +560,29 @@ int board_ehci_hcd_init(int port)
>> }
>> return 0;
>> }
>> +
>> +int board_usb_phy_mode(int port)
>> +{
>> + switch (port) {
>> + case 0:
>> + /*
>> + * Port 0 is used only in client mode on Colibri Vybrid modules
>> + * Check for state of USB client gpio pin and accordingly return
>> + * USB_INIT_DEVICE or USB_INIT_HOST.
>> + */
>> + if (gpio_get_value(USB_CDET_GPIO))
>> + return USB_INIT_DEVICE;
>> + else
>> + return USB_INIT_HOST;
>> + case 1:
>> + /* Port 1 is used only in host mode on Colibri Vybrid modules */
>> + return USB_INIT_HOST;
>> + default:
>> + /*
>> + * There are only two USB controllers on Vybrid. Ideally we will
>> + * not reach here. However return USB_INIT_HOST if we do.
>> + */
>> + return USB_INIT_HOST;
>> + }
>> +}
>> #endif
>> --
>> 2.6.2
>>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
