Used BIT macro on zynq_spi.c and zynq_qspi.c :%s/(1 << nr)/BIT(nr)/g where nr = 0, 1, 2 .... 31
Cc: Siva Durga Prasad Paladugu <siva...@xilinx.com> Cc: Michal Simek <michal.si...@xilinx.com> Reviewed-by: Tom Rini <tr...@konsulko.com> Signed-off-by: Jagan Teki <jt...@openedev.com> --- drivers/spi/zynq_qspi.c | 20 ++++++++++---------- drivers/spi/zynq_spi.c | 16 ++++++++-------- 2 files changed, 18 insertions(+), 18 deletions(-) diff --git a/drivers/spi/zynq_qspi.c b/drivers/spi/zynq_qspi.c index 8aa61d7..dd530a1 100644 --- a/drivers/spi/zynq_qspi.c +++ b/drivers/spi/zynq_qspi.c @@ -16,20 +16,20 @@ DECLARE_GLOBAL_DATA_PTR; /* zynq qspi register bit masks ZYNQ_QSPI_<REG>_<BIT>_MASK */ -#define ZYNQ_QSPI_CR_IFMODE_MASK (1 << 31) /* Flash intrface mode*/ -#define ZYNQ_QSPI_CR_MSA_MASK (1 << 15) /* Manual start enb */ -#define ZYNQ_QSPI_CR_MCS_MASK (1 << 14) /* Manual chip select */ -#define ZYNQ_QSPI_CR_PCS_MASK (1 << 10) /* Peri chip select */ +#define ZYNQ_QSPI_CR_IFMODE_MASK BIT(31) /* Flash intrface mode*/ +#define ZYNQ_QSPI_CR_MSA_MASK BIT(15) /* Manual start enb */ +#define ZYNQ_QSPI_CR_MCS_MASK BIT(14) /* Manual chip select */ +#define ZYNQ_QSPI_CR_PCS_MASK BIT(10) /* Peri chip select */ #define ZYNQ_QSPI_CR_FW_MASK (0x3 << 6) /* FIFO width */ #define ZYNQ_QSPI_CR_SS_MASK (0xF << 10) /* Slave Select */ #define ZYNQ_QSPI_CR_BAUD_MASK (0x7 << 3) /* Baud rate div */ -#define ZYNQ_QSPI_CR_CPHA_MASK (1 << 2) /* Clock phase */ -#define ZYNQ_QSPI_CR_CPOL_MASK (1 << 1) /* Clock polarity */ -#define ZYNQ_QSPI_CR_MSTREN_MASK (1 << 0) /* Mode select */ -#define ZYNQ_QSPI_IXR_RXNEMPTY_MASK (1 << 4) /* RX_FIFO_not_empty */ -#define ZYNQ_QSPI_IXR_TXOW_MASK (1 << 2) /* TX_FIFO_not_full */ +#define ZYNQ_QSPI_CR_CPHA_MASK BIT(2) /* Clock phase */ +#define ZYNQ_QSPI_CR_CPOL_MASK BIT(1) /* Clock polarity */ +#define ZYNQ_QSPI_CR_MSTREN_MASK BIT(0) /* Mode select */ +#define ZYNQ_QSPI_IXR_RXNEMPTY_MASK BIT(4) /* RX_FIFO_not_empty */ +#define ZYNQ_QSPI_IXR_TXOW_MASK BIT(2) /* TX_FIFO_not_full */ #define ZYNQ_QSPI_IXR_ALL_MASK 0x7F /* All IXR bits */ -#define ZYNQ_QSPI_ENR_SPI_EN_MASK (1 << 0) /* SPI Enable */ +#define ZYNQ_QSPI_ENR_SPI_EN_MASK BIT(0) /* SPI Enable */ /* zynq qspi Transmit Data Register */ #define ZYNQ_QSPI_TXD_00_00_OFFSET 0x1C /* Transmit 4-byte inst */ diff --git a/drivers/spi/zynq_spi.c b/drivers/spi/zynq_spi.c index 65a9633..92e5712 100644 --- a/drivers/spi/zynq_spi.c +++ b/drivers/spi/zynq_spi.c @@ -20,17 +20,17 @@ DECLARE_GLOBAL_DATA_PTR; /* zynq spi register bit masks ZYNQ_SPI_<REG>_<BIT>_MASK */ -#define ZYNQ_SPI_CR_MSA_MASK (1 << 15) /* Manual start enb */ -#define ZYNQ_SPI_CR_MCS_MASK (1 << 14) /* Manual chip select */ +#define ZYNQ_SPI_CR_MSA_MASK BIT(15) /* Manual start enb */ +#define ZYNQ_SPI_CR_MCS_MASK BIT(14) /* Manual chip select */ #define ZYNQ_SPI_CR_CS_MASK (0xF << 10) /* Chip select */ #define ZYNQ_SPI_CR_BAUD_MASK (0x7 << 3) /* Baud rate div */ -#define ZYNQ_SPI_CR_CPHA_MASK (1 << 2) /* Clock phase */ -#define ZYNQ_SPI_CR_CPOL_MASK (1 << 1) /* Clock polarity */ -#define ZYNQ_SPI_CR_MSTREN_MASK (1 << 0) /* Mode select */ -#define ZYNQ_SPI_IXR_RXNEMPTY_MASK (1 << 4) /* RX_FIFO_not_empty */ -#define ZYNQ_SPI_IXR_TXOW_MASK (1 << 2) /* TX_FIFO_not_full */ +#define ZYNQ_SPI_CR_CPHA_MASK BIT(2) /* Clock phase */ +#define ZYNQ_SPI_CR_CPOL_MASK BIT(1) /* Clock polarity */ +#define ZYNQ_SPI_CR_MSTREN_MASK BIT(0) /* Mode select */ +#define ZYNQ_SPI_IXR_RXNEMPTY_MASK BIT(4) /* RX_FIFO_not_empty */ +#define ZYNQ_SPI_IXR_TXOW_MASK BIT(2) /* TX_FIFO_not_full */ #define ZYNQ_SPI_IXR_ALL_MASK 0x7F /* All IXR bits */ -#define ZYNQ_SPI_ENR_SPI_EN_MASK (1 << 0) /* SPI Enable */ +#define ZYNQ_SPI_ENR_SPI_EN_MASK BIT(0) /* SPI Enable */ #define ZYNQ_SPI_CR_BAUD_MAX 8 /* Baud rate divisor max val */ #define ZYNQ_SPI_CR_BAUD_SHIFT 3 /* Baud rate divisor shift */ -- 1.9.1 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
