Hi York,
Please see my comments below.
> -----Original Message-----
> From: Sun York-R58495
> Sent: Monday, September 14, 2015 11:57 PM
> To: Lu Yangbo-B47093; u-boot@lists.denx.de
> Subject: Re: [PATCH 1/3] mmc: fsl_esdhc: enable dat[4:7] for eMMC4.5
>
> Yangbo,
>
> On 09/13/2015 08:04 PM, Yangbo Lu wrote:
> > If adapter card type identification is supported for platform, we
> > would enable dat[4:7] for eMMC4.5 card.
> >
> > Signed-off-by: Yangbo Lu <yangbo...@freescale.com>
> > Cc: York Sun <york...@freescale.com>
> > ---
> > board/freescale/common/qixis.h | 2 ++
> > drivers/mmc/fsl_esdhc.c | 3 +++
> > 2 files changed, 5 insertions(+)
> >
> > diff --git a/board/freescale/common/qixis.h
> > b/board/freescale/common/qixis.h index 51ce9c3..450cd0d 100644
> > --- a/board/freescale/common/qixis.h
> > +++ b/board/freescale/common/qixis.h
> > @@ -127,6 +127,8 @@ void qixis_write_i2c(unsigned int reg, u8 value);
> > #define QIXIS_ESDHC_NO_ADAPTER 0x7 /* No Card is
> Present*/
> > #define QIXIS_SDCLKIN 0x08
> > #define QIXIS_SDCLKOUT 0x02
> > +#define QIXIS_DAT5_6_7 0X02
> > +#define QIXIS_DAT4 0X01
> > #endif
> >
> > #endif
> > diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c index
> > 0b37002..639ec02 100644
> > --- a/drivers/mmc/fsl_esdhc.c
> > +++ b/drivers/mmc/fsl_esdhc.c
> > @@ -747,6 +747,9 @@ void mmc_adapter_card_type_ident(void)
> >
> > switch (card_id) {
> > case QIXIS_ESDHC_ADAPTER_TYPE_EMMC45:
> > + value = QIXIS_READ(brdcfg[5]);
> > + value |= (QIXIS_DAT4 | QIXIS_DAT5_6_7);
> > + QIXIS_WRITE(brdcfg[5], value);
> > break;
> > case QIXIS_ESDHC_ADAPTER_TYPE_SDMMC_LEGACY:
> > break;
> >
>
> Does any other board have this identification feature? I see the code
> only use qixis. How are RDB and customer boards handled?
>
> York
[Lu Yangbo-B47093] This feature is used for QDS boards that use SDHC Adapter
card. Now only T1040QDS and T2080QDS are enabled, because we want to support
SD/MMC UHS-I speed mode on these two boards in kernel and these QIXIS
configuration are needed for *the Adapter*. For RDB and customer boards, they
don't use Adapter card and the default configuration is ok for SD/MMC Default
speed mode and High speed mode.
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
