The dw_mmc driver uses printf() in various places.

These bloat the code and cause problems for SPL. Use debug() where possible
and try to return a useful error code instead.

Signed-off-by: Simon Glass <s...@chromium.org>
---

Changes in v4:
- Update commit message to indicate this patch is for the dw_mmc driver

 drivers/mmc/dw_mmc.c | 21 +++++++++++----------
 1 file changed, 11 insertions(+), 10 deletions(-)

diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
index 53a8aca..8f28d7e 100644
--- a/drivers/mmc/dw_mmc.c
+++ b/drivers/mmc/dw_mmc.c
@@ -8,6 +8,7 @@
 
 #include <bouncebuf.h>
 #include <common.h>
+#include <errno.h>
 #include <malloc.h>
 #include <mmc.h>
 #include <dwmmc.h>
@@ -119,7 +120,7 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd 
*cmd,
 
        while (dwmci_readl(host, DWMCI_STATUS) & DWMCI_BUSY) {
                if (get_timer(start) > timeout) {
-                       printf("%s: Timeout on data busy\n", __func__);
+                       debug("%s: Timeout on data busy\n", __func__);
                        return TIMEOUT;
                }
        }
@@ -178,7 +179,7 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd 
*cmd,
        }
 
        if (i == retry) {
-               printf("%s: Timeout.\n", __func__);
+               debug("%s: Timeout.\n", __func__);
                return TIMEOUT;
        }
 
@@ -194,8 +195,8 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd 
*cmd,
                debug("%s: Response Timeout.\n", __func__);
                return TIMEOUT;
        } else if (mask & DWMCI_INTMSK_RE) {
-               printf("%s: Response Error.\n", __func__);
-               return -1;
+               debug("%s: Response Error.\n", __func__);
+               return -EIO;
        }
 
 
@@ -214,7 +215,7 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd 
*cmd,
                do {
                        mask = dwmci_readl(host, DWMCI_RINTSTS);
                        if (mask & (DWMCI_DATA_ERR | DWMCI_DATA_TOUT)) {
-                               printf("%s: DATA ERROR!\n", __func__);
+                               debug("%s: DATA ERROR!\n", __func__);
                                return -1;
                        }
                } while (!(mask & DWMCI_INTMSK_DTO));
@@ -251,7 +252,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 
freq)
        else if (host->bus_hz)
                sclk = host->bus_hz;
        else {
-               printf("%s: Didn't get source clock value.\n", __func__);
+               debug("%s: Didn't get source clock value.\n", __func__);
                return -EINVAL;
        }
 
@@ -270,7 +271,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 
freq)
        do {
                status = dwmci_readl(host, DWMCI_CMD);
                if (timeout-- < 0) {
-                       printf("%s: Timeout!\n", __func__);
+                       debug("%s: Timeout!\n", __func__);
                        return -ETIMEDOUT;
                }
        } while (status & DWMCI_CMD_START);
@@ -285,7 +286,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 
freq)
        do {
                status = dwmci_readl(host, DWMCI_CMD);
                if (timeout-- < 0) {
-                       printf("%s: Timeout!\n", __func__);
+                       debug("%s: Timeout!\n", __func__);
                        return -ETIMEDOUT;
                }
        } while (status & DWMCI_CMD_START);
@@ -339,8 +340,8 @@ static int dwmci_init(struct mmc *mmc)
        dwmci_writel(host, DWMCI_PWREN, 1);
 
        if (!dwmci_wait_reset(host, DWMCI_RESET_ALL)) {
-               printf("%s[%d] Fail-reset!!\n", __func__, __LINE__);
-               return -1;
+               debug("%s[%d] Fail-reset!!\n", __func__, __LINE__);
+               return -EIO;
        }
 
        /* Enumerate at 400KHz */
-- 
2.5.0.rc2.392.g76e840b

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to