Hi Simon,
On Wed, Jul 29, 2015 at 5:01 PM, Bin Meng <bmeng...@gmail.com> wrote:
> Hi Simon,
>
> On Wed, Jul 29, 2015 at 9:08 AM, Bin Meng <bmeng...@gmail.com> wrote:
>> Hi Simon,
>>
>> On Wed, Jul 29, 2015 at 8:48 AM, Simon Glass <s...@chromium.org> wrote:
>>> Hi Bin,
>>>
>>> On 28 July 2015 at 18:46, Bin Meng <bmeng...@gmail.com> wrote:
>>>> Hi Simon,
>>>>
>>>> On Wed, Jul 29, 2015 at 8:42 AM, Simon Glass <s...@chromium.org> wrote:
>>>>> Hi Bin,
>>>>>
>>>>> On 28 July 2015 at 18:40, Bin Meng <bmeng...@gmail.com> wrote:
>>>>>> Hi Simon,
>>>>>>
>>>>>> On Tue, Jul 28, 2015 at 7:58 PM, Simon Glass <s...@chromium.org> wrote:
>>>>>>> Hi Bin,
>>>>>>>
>>>>>>> On 28 July 2015 at 01:50, Bin Meng <bmeng...@gmail.com> wrote:
>>>>>>>>
>>>>>>>> Hi Simon,
>>>>>>>>
>>>>>>>> On Tue, Jul 28, 2015 at 5:47 AM, Simon Glass <s...@chromium.org> wrote:
>>>>>>>> > At present minnowmax does not correct set up PCI interrupts. This
>>>>>>>> > should be
>>>>>>>> > done in U-Boot so that devices work correctly in Linux.
>>>>>>>> >
>>>>>>>> > Note: This code needs to make use of the recent pirq_routing work.
>>>>>>>> > It does
>>>>>>>> > not seem to support all the required features, so this RFC will
>>>>>>>> > hopefully
>>>>>>>>
>>>>>>>> What features are missing in the existing PIRQ codes? When I did the
>>>>>>>> PIRQ support, I checked both TunnelCreek and BayTrail chipset
>>>>>>>> datasheet, and found the only difference seems to be the pci
>>>>>>>> configuration space vs. memory-mapped IBASE where the pci irq routing
>>>>>>>> registers reside.
>>>>>>>
>>>>>>> I see that each PCI device can be assigned four routes, making up a
>>>>>>> 16-bit register. But the code I see in pirq_assign_req() only assigns
>>>>>>> a single one, using a byte register.
>>>>>>>
>>>>>>
>>>>>> No, the pci irq routing register is still a 8-bit register on
>>>>>> BayTrail, where pirq_assign_irq() programs. The 16-bit register you
>>>>>> mentioned should be done in the platform codes. See
>>>>>> arch/x86/cpu/queensbay/tnc.c::cpu_irq_init(). By the way actually we
>>>>>> can leave those register programmed as they have the optimized default
>>>>>> values for all pci devices after power up, unless we intentionally
>>>>>> want to change them.
>>>>>
>>>>> What do you mean by 'leave those register programmed'?
>>>>>
>>>>
>>>> I mean their default value is normally OK, like INTA maps PIRQA, INTB
>>>> maps PIRQB, INTC maps PIRQC and INTD maps PIRQD.
>>>
>>> OK, so drop writing to the pirq registers?
>>
>> You might need check if BayTrail FSP does any programming on these
>> registers. On Intel Crown Bay, I checked those values are the same
>> values as documented in the TunnelCreek datasheet.
>>
>>> Should I program the 16-bit registers? If so, I will need to extend
>>> the device tree binding, won't I?
>>
>> When I did the device tree binding changes, I did not convert these
>> registers to use device tree, because their offsets, not like the
>> routing registers as programmed in pirq_assign_irq(), is really
>> platform specific thing and does not seem to have a good formula to
>> calculate its offset (it varies from platform to platform). I
>> previously wanted to create some device bindings like below, but I
>> think they are really ugly so I did not go that way:
>>
>> irq-router@1f,0 {
>> reg = <0x0000f800 0 0 0 0>;
>> compatible = "intel,irq-router";
>> ......
>> dev0-intx-offset = <0x2040>;
>> dev0-intx-value = <PIRQA PIRQB PIRQC PIRQD>;
>> dev2-intx-offset = <0x2048>;
>> dev2-intx-value = <PIRQA PIRQB PIRQC PIRQD>;
>> dev4-intx-offset = <0x2060>;
>> dev4-intx-value = <PIRQA PIRQB PIRQC PIRQD>;
>> dev26-intx-offset = <0x20a0>;
>> dev26-intx-value = <PIRQA PIRQB PIRQC PIRQD>;
>> dev31-intx-offset = <0x20c0>;
>> dev31-intx-value = <PIRQA PIRQB PIRQC PIRQD>;
>> ......
>>
>> Sorry I cannot find a better way to describe this in device tree, so I
>> chose to implement directly in the cpu_irq_init() to program these
>> registers.
>>
>>>
>>> Sorry my understanding is limited on this - and I'd like to use your
>>> generic code if possible.
>>>
>>
>> Yes, let's try to use the existing codes. If needed, we can have some
>> patches to support new platforms.
>>
>
> I just managed to get a BayTrail board (not MinnowMax) and will try to
> first port U-Boot (assume it won't take much time) then see how PIRQ
> looks like on this platform.
>
It turns out the existing PIRQ codes works pretty well on BayTrail.
Please check this patch: http://patchwork.ozlabs.org/patch/502058/
Regards,
Bin
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
