* Add thermal driver support for imx7 SoC
read_cpu_temperature is SoC dependent
* Redefine config macro to support imx7 and imx6 SoC
Signed-off-by: Adrian Alonso <aalo...@freescale.com>
Signed-off-by: Peng Fan <peng....@freescale.com>
---
Changes for V2:
- Rework patch so it can be applyed on top of patch
imx6: standardise OCOTP and fuse config to mx6_common
arch/arm/imx-common/cpu.c | 10 ++--
drivers/thermal/Makefile | 2 +-
drivers/thermal/imx_thermal.c | 100 +++++++++++++++++++++++++++++++++++---
include/configs/embestmx6boards.h | 2 +-
include/configs/gw_ventana.h | 2 +-
include/configs/mx6cuboxi.h | 2 +-
include/configs/mx6sabre_common.h | 2 +-
include/configs/mx6slevk.h | 2 +-
include/configs/mx6sxsabresd.h | 2 +-
include/configs/tbs2910.h | 2 +-
10 files changed, 108 insertions(+), 18 deletions(-)
diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
index 5e56cfe..2e803f3 100644
--- a/arch/arm/imx-common/cpu.c
+++ b/arch/arm/imx-common/cpu.c
@@ -148,14 +148,16 @@ int print_cpuinfo(void)
u32 cpurev;
__maybe_unused u32 max_freq;
-#if defined(CONFIG_MX6) && defined(CONFIG_IMX6_THERMAL)
+#if defined(CONFIG_IMX_THERMAL)
struct udevice *thermal_dev;
- int cpu_tmp, minc, maxc, ret;
+ int cpu_tmp, ret;
#endif
cpurev = get_cpu_rev();
#if defined(CONFIG_MX6)
+ int minc, maxc;
+
printf("CPU: Freescale i.MX%s rev%d.%d",
get_imx_type((cpurev & 0xFF000) >> 12),
(cpurev & 0x000F0) >> 4,
@@ -175,7 +177,7 @@ int print_cpuinfo(void)
mxc_get_clock(MXC_ARM_CLK) / 1000000);
#endif
-#if defined(CONFIG_MX6) && defined(CONFIG_IMX6_THERMAL)
+#if defined(CONFIG_MX6) && defined(CONFIG_IMX_THERMAL)
puts("CPU: ");
switch (get_cpu_temp_grade(&minc, &maxc)) {
case TEMP_AUTOMOTIVE:
@@ -192,6 +194,8 @@ int print_cpuinfo(void)
break;
}
printf("(%dC to %dC)", minc, maxc);
+#endif
+#if defined(CONFIG_IMX_THERMAL)
ret = uclass_get_device(UCLASS_THERMAL, 0, &thermal_dev);
if (!ret) {
ret = thermal_get_temp(thermal_dev, &cpu_tmp);
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 6d4cacd..d768f5e 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -6,4 +6,4 @@
#
obj-$(CONFIG_DM_THERMAL) += thermal-uclass.o
-obj-$(CONFIG_IMX6_THERMAL) += imx_thermal.o
+obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o
diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
index 0d893c9..046c094 100644
--- a/drivers/thermal/imx_thermal.c
+++ b/drivers/thermal/imx_thermal.c
@@ -19,6 +19,14 @@
#include <thermal.h>
#include <imx_thermal.h>
+struct thermal_data {
+ unsigned int fuse;
+ int critical;
+ int minc;
+ int maxc;
+};
+
+#if defined(CONFIG_MX6)
/* board will busyloop until this many degrees C below CPU max temperature */
#define TEMPERATURE_HOT_DELTA 5 /* CPU maxT - 5C */
#define FACTOR0 10000000
@@ -34,13 +42,6 @@
#define MISC0_REFTOP_SELBIASOFF (1 << 3)
#define TEMPSENSE1_MEASURE_FREQ 0xffff
-struct thermal_data {
- unsigned int fuse;
- int critical;
- int minc;
- int maxc;
-};
-
static int read_cpu_temperature(struct udevice *dev)
{
int temperature;
@@ -124,6 +125,79 @@ static int read_cpu_temperature(struct udevice *dev)
return temperature;
}
+#elif defined(CONFIG_MX7)
+#define TEMPERATURE_MIN -40
+#define TEMPERATURE_HOT 85
+#define TEMPERATURE_MAX 125
+#define MEASURE_FREQ 327
+
+static int read_cpu_temperature(struct udevice *dev)
+{
+ unsigned int reg, tmp, start;
+ unsigned int raw_25c, te1;
+ int temperature;
+ unsigned int *priv = dev_get_priv(dev);
+ u32 fuse = *priv;
+ struct mxc_ccm_anatop_reg *ccm_anatop = (struct mxc_ccm_anatop_reg *)
+ ANATOP_BASE_ADDR;
+ /*
+ * fuse data layout:
+ * [31:21] sensor value @ 25C
+ * [20:18] hot temperature value
+ * [17:9] sensor value of room
+ * [8:0] sensor value of hot
+ */
+
+ raw_25c = fuse >> 21;
+ if (raw_25c == 0)
+ raw_25c = 25;
+
+ te1 = (fuse >> 9) & 0x1ff;
+
+ /*
+ * now we only use single measure, every time we read
+ * the temperature, we will power on/down anadig thermal
+ * module
+ */
+ writel(TEMPMON_HW_ANADIG_TEMPSENSE1_POWER_DOWN_MASK,
&ccm_anatop->tempsense1_clr);
+ writel(PMU_REF_REFTOP_SELFBIASOFF_MASK, &ccm_anatop->ref_set);
+
+ /* write measure freq */
+ reg = readl(&ccm_anatop->tempsense1);
+ reg &= ~TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_FREQ_MASK;
+ reg |= TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_FREQ(MEASURE_FREQ);
+ writel(reg, &ccm_anatop->tempsense1);
+
+ writel(TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_TEMP_MASK,
&ccm_anatop->tempsense1_clr);
+ writel(TEMPMON_HW_ANADIG_TEMPSENSE1_FINISHED_MASK,
&ccm_anatop->tempsense1_clr);
+ writel(TEMPMON_HW_ANADIG_TEMPSENSE1_MEASURE_TEMP_MASK,
&ccm_anatop->tempsense1_set);
+
+ start = get_timer(0);
+ /* Wait max 100ms */
+ do {
+ /*
+ * Since we can not rely on finish bit, use 1ms delay to get
+ * temperature. From RM, 17us is enough to get data, but
+ * to gurantee to get the data, delay 100ms here.
+ */
+ reg = readl(&ccm_anatop->tempsense1);
+ tmp = (reg & TEMPMON_HW_ANADIG_TEMPSENSE1_TEMP_VALUE_MASK)
+ >> TEMPMON_HW_ANADIG_TEMPSENSE1_TEMP_VALUE_SHIFT;
+ } while (get_timer(0) < (start + 100));
+
+ writel(TEMPMON_HW_ANADIG_TEMPSENSE1_FINISHED_MASK,
&ccm_anatop->tempsense1_clr);
+
+ /* power down anatop thermal sensor */
+ writel(TEMPMON_HW_ANADIG_TEMPSENSE1_POWER_DOWN_MASK,
&ccm_anatop->tempsense1_set);
+ writel(PMU_REF_REFTOP_SELFBIASOFF_MASK, &ccm_anatop->ref_clr);
+
+ /* Single point */
+ temperature = tmp - (te1 - raw_25c);
+
+ return temperature;
+}
+#endif
+
int imx_thermal_get_temp(struct udevice *dev, int *temp)
{
struct thermal_data *priv = dev_get_priv(dev);
@@ -161,15 +235,27 @@ static int imx_thermal_probe(struct udevice *dev)
/* Read Temperature calibration data fuse */
fuse_read(pdata->fuse_bank, pdata->fuse_word, &fuse);
+#if defined(CONFIG_MX6)
/* Check for valid fuse */
if (fuse == 0 || fuse == ~0) {
printf("CPU: Thermal invalid data, fuse: 0x%x\n", fuse);
return -EPERM;
}
+#elif defined(CONFIG_MX7)
+ /* No Calibration data in FUSE? */
+ if ((fuse & 0x3ffff) == 0) {
+ printf("CPU: Thermal invalid data, fuse: 0x%x\n", fuse);
+ return -EPERM;
+ }
+#else
+#error "Not support thermal driver"
+#endif
+#if defined(CONFIG_MX6)
/* set critical cooling temp */
get_cpu_temp_grade(&priv->minc, &priv->maxc);
priv->critical = priv->maxc - TEMPERATURE_HOT_DELTA;
+#endif
priv->fuse = fuse;
enable_thermal_clk();
diff --git a/include/configs/embestmx6boards.h
b/include/configs/embestmx6boards.h
index 12744a6..58cee96 100644
--- a/include/configs/embestmx6boards.h
+++ b/include/configs/embestmx6boards.h
@@ -19,7 +19,7 @@
#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
-#define CONFIG_IMX6_THERMAL
+#define CONFIG_IMX_THERMAL
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h
index df1ff43..240b109 100644
--- a/include/configs/gw_ventana.h
+++ b/include/configs/gw_ventana.h
@@ -57,7 +57,7 @@
#define CONFIG_CMD_GPIO
/* Thermal */
-#define CONFIG_IMX6_THERMAL
+#define CONFIG_IMX_THERMAL
/* Serial */
#define CONFIG_MXC_UART
diff --git a/include/configs/mx6cuboxi.h b/include/configs/mx6cuboxi.h
index 634a09f..6e89dd1 100644
--- a/include/configs/mx6cuboxi.h
+++ b/include/configs/mx6cuboxi.h
@@ -14,7 +14,7 @@
#define CONFIG_SPL_MMC_SUPPORT
#include "imx6_spl.h"
-#define CONFIG_IMX6_THERMAL
+#define CONFIG_IMX_THERMAL
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
#define CONFIG_BOARD_EARLY_INIT_F
diff --git a/include/configs/mx6sabre_common.h
b/include/configs/mx6sabre_common.h
index e42dfc9..4f1be15 100644
--- a/include/configs/mx6sabre_common.h
+++ b/include/configs/mx6sabre_common.h
@@ -11,7 +11,7 @@
#include "mx6_common.h"
-#define CONFIG_IMX6_THERMAL
+#define CONFIG_IMX_THERMAL
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h
index 3cecd94..58e59d8 100644
--- a/include/configs/mx6slevk.h
+++ b/include/configs/mx6slevk.h
@@ -190,6 +190,6 @@
#define CONFIG_SYS_MMC_ENV_DEV 1 /* SDHC2*/
#endif
-#define CONFIG_IMX6_THERMAL
+#define CONFIG_IMX_THERMAL
#endif /* __CONFIG_H */
diff --git a/include/configs/mx6sxsabresd.h b/include/configs/mx6sxsabresd.h
index 848bdcd..381eaa2 100644
--- a/include/configs/mx6sxsabresd.h
+++ b/include/configs/mx6sxsabresd.h
@@ -176,7 +176,7 @@
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(2, 1)
#endif
-#define CONFIG_IMX6_THERMAL
+#define CONFIG_IMX_THERMAL
#define CONFIG_CMD_TIME
diff --git a/include/configs/tbs2910.h b/include/configs/tbs2910.h
index 5bc1209..7c61cb9 100644
--- a/include/configs/tbs2910.h
+++ b/include/configs/tbs2910.h
@@ -21,7 +21,7 @@
#define CONFIG_SYS_PROMPT "Matrix U-Boot> "
#define CONFIG_SYS_HZ 1000
-#define CONFIG_IMX6_THERMAL
+#define CONFIG_IMX_THERMAL
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
--
2.1.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
