From: yassin <yassinjaf...@gmail.com> Signed-off-by: Roy Spliet <r.spl...@ultimaker.com> --- drivers/mtd/nand/nand_base.c | 101 ++++++++++++++++++++++++++----------------- 1 file changed, 61 insertions(+), 40 deletions(-)
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index 1c514a0..83586cc 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -4114,47 +4114,15 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips, } EXPORT_SYMBOL(nand_scan_ident); - -/** - * nand_scan_tail - [NAND Interface] Scan for the NAND device - * @mtd: MTD device structure - * - * This is the second phase of the normal nand_scan() function. It fills out - * all the uninitialized function pointers with the defaults and scans for a - * bad block table if appropriate. +/* + * Initialize ECC struct: + * - fill ECC struct with default function/values when these ones are undefined + * - fill ECC infos based on MTD device */ -int nand_scan_tail(struct mtd_info *mtd) +static int nand_ecc_ctrl_init(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc) { int i; - struct nand_chip *chip = mtd->priv; - struct nand_ecc_ctrl *ecc = &chip->ecc; - struct nand_buffers *nbuf; - /* New bad blocks should be marked in OOB, flash-based BBT, or both */ - BUG_ON((chip->bbt_options & NAND_BBT_NO_OOB_BBM) && - !(chip->bbt_options & NAND_BBT_USE_FLASH)); - - if (!(chip->options & NAND_OWN_BUFFERS)) { -#ifndef __UBOOT__ - nbuf = kzalloc(sizeof(*nbuf) + mtd->writesize - + mtd->oobsize * 3, GFP_KERNEL); - if (!nbuf) - return -ENOMEM; - nbuf->ecccalc = (uint8_t *)(nbuf + 1); - nbuf->ecccode = nbuf->ecccalc + mtd->oobsize; - nbuf->databuf = nbuf->ecccode + mtd->oobsize; -#else - nbuf = kzalloc(sizeof(struct nand_buffers), GFP_KERNEL); -#endif - - chip->buffers = nbuf; - } else { - if (!chip->buffers) - return -ENOMEM; - } - - /* Set the internal oob buffer location, just after the page data */ - chip->oob_poi = chip->buffers->databuf + mtd->writesize; /* * If no default placement scheme is given, select an appropriate one. @@ -4180,9 +4148,6 @@ int nand_scan_tail(struct mtd_info *mtd) } } - if (!chip->write_page) - chip->write_page = nand_write_page; - /* * Check ECC mode, default to software if 3byte/512byte hardware ECC is * selected and we have 256 byte pagesize fallback to software ECC @@ -4349,6 +4314,62 @@ int nand_scan_tail(struct mtd_info *mtd) } ecc->total = ecc->steps * ecc->bytes; + return 0; +} + +/** + * nand_scan_tail - [NAND Interface] Scan for the NAND device + * @mtd: MTD device structure + * + * This is the second phase of the normal nand_scan() function. It fills out + * all the uninitialized function pointers with the defaults and scans for a + * bad block table if appropriate. + */ +int nand_scan_tail(struct mtd_info *mtd) +{ + int ret; + struct nand_chip *chip = mtd->priv; + struct nand_ecc_ctrl *ecc = &chip->ecc; + struct nand_buffers *nbuf; + + /* New bad blocks should be marked in OOB, flash-based BBT, or both */ + BUG_ON((chip->bbt_options & NAND_BBT_NO_OOB_BBM) && + !(chip->bbt_options & NAND_BBT_USE_FLASH)); + + if (!(chip->options & NAND_OWN_BUFFERS)) { +#ifndef __UBOOT__ + nbuf = kzalloc(sizeof(*nbuf) + mtd->writesize + + mtd->oobsize * 3, GFP_KERNEL); + if (!nbuf) + return -ENOMEM; + nbuf->ecccalc = (uint8_t *)(nbuf + 1); + nbuf->ecccode = nbuf->ecccalc + mtd->oobsize; + nbuf->databuf = nbuf->ecccode + mtd->oobsize; +#else + nbuf = kzalloc(sizeof(struct nand_buffers), GFP_KERNEL); +#endif + + chip->buffers = nbuf; + } else { + if (!chip->buffers) + return -ENOMEM; + } + + /* Set the internal oob buffer location, just after the page data */ + chip->oob_poi = chip->buffers->databuf + mtd->writesize; + + if (!chip->write_page) + chip->write_page = nand_write_page; + + /* Initialize ECC struct */ + ret = nand_ecc_ctrl_init(mtd, ecc); + if (ret) { + if (!(chip->options & NAND_OWN_BUFFERS)) + kfree(chip->buffers); + + return ret; + } + /* Allow subpage writes up to ecc.steps. Not possible for MLC flash */ if (!(chip->options & NAND_NO_SUBPAGE_WRITE) && nand_is_slc(chip)) { switch (ecc->steps) { -- 2.4.2 -- IMAGINE IT >> MAKE IT Meet us online at Twitter <http://twitter.com/ultimaker>, Facebook <http://facebook.com/ultimaker>, Google+ <http://google.com/+Ultimaker> www.ultimaker.com _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot