Hi Simon,
I just submitted a new version of the patch, actually, when I tried to
use the GPIO on the header I saw a typo in the code.
To test it, you have to define these nodes in the device tree (should be
there by default or not?):
soc_gpio_s5_0@0 {
gpio-offset = <0x80 0>;
pad-offset = <0x1d0>;
mode-gpio;
output-value = <0>;
direction = <PIN_OUTPUT>;
};
soc_gpio_s5_1@0 {
gpio-offset = <0x80 1>;
pad-offset = <0x210>;
mode-gpio;
output-value = <0>;
direction = <PIN_OUTPUT>;
};
soc_gpio_s5_2@0 {
gpio-offset = <0x80 2>;
pad-offset = <0x1e0>;
mode-gpio;
output-value = <0>;
direction = <PIN_OUTPUT>;
};
And after, you can use the GPIO commands:
=> gpio set E0
gpio: pin E0 (gpio 128) value is 1
=> gpio clear E0
gpio: pin E0 (gpio 128) value is 0
=> gpio set E2
gpio: pin E2 (gpio 130) value is 1
=> gpio clear E2
gpio: pin E2 (gpio 130) value is 0
E0 E1 and E2 correspond to the GPIO0 1 and 2.
Regards,
Gabriel
On 05/20/2015 07:21 AM, Simon Glass wrote:
Hi Gabriel,
I have two patches in patchwork:
http://patchwork.ozlabs.org/patch/471146/
http://patchwork.ozlabs.org/patch/471147/
Are they the correct ones? Also do you know how to use the gpio
command to toggle a bin on the Minnowboard MAX header? I'd like to try
that.
Regards,
Simon
On 12 May 2015 at 00:20, gabriel huau <cont...@huau-gabriel.fr> wrote:
Please ignore this email/patch, I put the wrong message id ...
On 05/11/2015 11:12 PM, Gabriel Huau wrote:
Signed-off-by: Gabriel Huau <cont...@huau-gabriel.fr>
Acked-by: Simon Glass <s...@chromium.org>
---
Changes in v3:
- Rebase to the origin/master
Changes in v2:
- Fix ordering of include header
board/intel/minnowmax/minnowmax.c | 9 +++++++++
include/configs/minnowmax.h | 1 +
2 files changed, 10 insertions(+)
diff --git a/board/intel/minnowmax/minnowmax.c
b/board/intel/minnowmax/minnowmax.c
index 1f5549a..383cae0 100644
--- a/board/intel/minnowmax/minnowmax.c
+++ b/board/intel/minnowmax/minnowmax.c
@@ -5,6 +5,7 @@
*/
#include <common.h>
+#include <asm/gpio.h>
#include <asm/ibmpc.h>
#include <asm/pnp_def.h>
#include <netdev.h>
@@ -12,6 +13,14 @@
#define SERIAL_DEV PNP_DEV(0x2e, 4)
+int arch_early_init_r(void)
+{
+ /* do the pin-muxing */
+ gpio_ich6_pinctrl_init();
+
+ return 0;
+}
+
int board_early_init_f(void)
{
lpc47m_enable_serial(SERIAL_DEV, UART0_BASE, UART0_IRQ);
diff --git a/include/configs/minnowmax.h b/include/configs/minnowmax.h
index eb35a50..547765d 100644
--- a/include/configs/minnowmax.h
+++ b/include/configs/minnowmax.h
@@ -15,6 +15,7 @@
#define CONFIG_SYS_MONITOR_LEN (1 << 20)
#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_ARCH_EARLY_INIT_R
#define CONFIG_X86_SERIAL
#define CONFIG_SMSC_LPC47M
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot