add support for imx6dl based aristainetos2 board
U-Boot 2015.04-rc5-00066-g60f6ed4 (Apr 10 2015 - 08:46:27)
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
Reset cause: WDOG
Board: aristaitenos2
Watchdog enabled
I2C: ready
DRAM: 1 GiB
NAND: 1024 MiB
MMC: FSL_SDHC: 0
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lg4573 (480x800)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
=>
Signed-off-by: Heiko Schocher <h...@denx.de>
---
Changes in v2:
- add comment from Stefano Babic:
- adapt for i2c fixes suggested by Stefano Babic
- remove lgdisplay var
- remove CONFIG_PHY_MICREL_KSZ9031
- rename enable_spi to enable_spi_display
- rotate logo remains in board code
arch/arm/Kconfig | 5 +
board/aristainetos2/Kconfig | 12 +
board/aristainetos2/MAINTAINERS | 6 +
board/aristainetos2/Makefile | 12 +
board/aristainetos2/aristainetos2.c | 922 ++++++++++++++++++++++++++++++++++
board/aristainetos2/aristainetos2.cfg | 34 ++
board/aristainetos2/axi.cfg | 22 +
board/aristainetos2/clocks.cfg | 24 +
board/aristainetos2/ddr-setup.cfg | 59 +++
board/aristainetos2/nt5cc256m16cp.cfg | 60 +++
configs/aristainetos2_defconfig | 3 +
include/configs/aristainetos2.h | 352 +++++++++++++
12 files changed, 1511 insertions(+)
create mode 100644 board/aristainetos2/Kconfig
create mode 100644 board/aristainetos2/MAINTAINERS
create mode 100644 board/aristainetos2/Makefile
create mode 100644 board/aristainetos2/aristainetos2.c
create mode 100644 board/aristainetos2/aristainetos2.cfg
create mode 100644 board/aristainetos2/axi.cfg
create mode 100644 board/aristainetos2/clocks.cfg
create mode 100644 board/aristainetos2/ddr-setup.cfg
create mode 100644 board/aristainetos2/nt5cc256m16cp.cfg
create mode 100644 configs/aristainetos2_defconfig
create mode 100644 include/configs/aristainetos2.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 49bcad1..287a9ff 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -523,6 +523,10 @@ config TARGET_ARISTAINETOS
bool "Support aristainetos"
select CPU_V7
+config TARGET_ARISTAINETOS2
+ bool "Support aristainetos2"
+ select CPU_V7
+
config TARGET_MX6QARM2
bool "Support mx6qarm2"
select CPU_V7
@@ -856,6 +860,7 @@ source "arch/arm/cpu/armv8/Kconfig"
source "arch/arm/imx-common/Kconfig"
source "board/aristainetos/Kconfig"
+source "board/aristainetos2/Kconfig"
source "board/BuR/kwb/Kconfig"
source "board/BuR/tseries/Kconfig"
source "board/CarMediaLab/flea3/Kconfig"
diff --git a/board/aristainetos2/Kconfig b/board/aristainetos2/Kconfig
new file mode 100644
index 0000000..2cf13e4
--- /dev/null
+++ b/board/aristainetos2/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_ARISTAINETOS2
+
+config SYS_BOARD
+ default "aristainetos2"
+
+config SYS_SOC
+ default "mx6"
+
+config SYS_CONFIG_NAME
+ default "aristainetos2"
+
+endif
diff --git a/board/aristainetos2/MAINTAINERS b/board/aristainetos2/MAINTAINERS
new file mode 100644
index 0000000..d155f86
--- /dev/null
+++ b/board/aristainetos2/MAINTAINERS
@@ -0,0 +1,6 @@
+ARISTAINETOS BOARD
+M: Heiko Schocher <h...@denx.de>
+S: Maintained
+F: board/aristainetos2/
+F: include/configs/aristainetos2.h
+F: configs/aristainetos2_defconfig
diff --git a/board/aristainetos2/Makefile b/board/aristainetos2/Makefile
new file mode 100644
index 0000000..2513744
--- /dev/null
+++ b/board/aristainetos2/Makefile
@@ -0,0 +1,12 @@
+#
+# (C) Copyright 2015
+# Heiko Schocher, DENX Software Engineering, h...@denx.de.
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <l...@denx.de>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := aristainetos2.o
diff --git a/board/aristainetos2/aristainetos2.c
b/board/aristainetos2/aristainetos2.c
new file mode 100644
index 0000000..3a7aac0
--- /dev/null
+++ b/board/aristainetos2/aristainetos2.c
@@ -0,0 +1,922 @@
+/*
+ * (C) Copyright 2015
+ * Heiko Schocher, DENX Software Engineering, h...@denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.este...@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <micrel.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <pwm.h>
+#include <spi.h>
+#include <video.h>
+#include <../drivers/video/ipu.h>
+#if defined(CONFIG_VIDEO_BMP_LOGO)
+ #include <bmp_logo.h>
+#endif
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC2_PAD_CTRL (PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+#define DISP_PAD_CTRL (0x10)
+
+#define ECSPI1_CS0 IMX_GPIO_NR(4, 9) /* 4.3 display controller */
+#define ECSPI4_CS0 IMX_GPIO_NR(3, 29)
+#define ECSPI4_CS1 IMX_GPIO_NR(5, 2) /* NOR boot flash */
+
+#define SOFT_RESET_GPIO IMX_GPIO_NR(7, 13)
+#define SD2_DRIVER_ENABLE IMX_GPIO_NR(7, 8)
+
+
+struct i2c_pads_info i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC,
+ .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC,
+ .gp = IMX_GPIO_NR(5, 27)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC,
+ .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
+ .gp = IMX_GPIO_NR(5, 26)
+ }
+};
+
+struct i2c_pads_info i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC,
+ .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC,
+ .gp = IMX_GPIO_NR(4, 12)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
+ .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC,
+ .gp = IMX_GPIO_NR(4, 13)
+ }
+};
+
+struct i2c_pads_info i2c_pad_info3 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC,
+ .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC,
+ .gp = IMX_GPIO_NR(1, 5)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
+ .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
+ .gp = IMX_GPIO_NR(1, 6)
+ }
+};
+
+struct i2c_pads_info i2c_pad_info4 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_GPIO_7__I2C4_SCL | PC,
+ .gpio_mode = MX6_PAD_GPIO_7__GPIO1_IO07 | PC,
+ .gp = IMX_GPIO_NR(1, 7)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_GPIO_8__I2C4_SDA | PC,
+ .gpio_mode = MX6_PAD_GPIO_8__GPIO1_IO08 | PC,
+ .gp = IMX_GPIO_NR(1, 8)
+ }
+};
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D19__UART1_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D20__UART1_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart2_pads[] = {
+ MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart3_pads[] = {
+ MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart4_pads[] = {
+ MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const gpio_pads[] = {
+ /* LED enable*/
+ MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* LED yellow */
+ MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* LED red */
+ MX6_PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* LED green */
+ MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* LED blue */
+ MX6_PAD_EIM_EB1__GPIO2_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* spi flash WP protect */
+ MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* spi CS 0 */
+ MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* spi bus #2 SS driver enable */
+ MX6_PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* RST_LOC# PHY reset input (has pull-down!)*/
+ MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* SD 2 level shifter output enable */
+ MX6_PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* SD1 card detect input */
+ MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* SD1 write protect input */
+ MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* SD2 card detect input */
+ MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* SD2 write protect input */
+ MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* Touchscreen IRQ */
+ MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const misc_pads[] = {
+ /* USB_OTG_ID = GPIO1_24*/
+ MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* H1 Power enable = GPIO1_0*/
+ MX6_PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* OTG Power enable = GPIO4_15*/
+ MX6_PAD_KEY_ROW4__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const enet_pads[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+}
+
+iomux_v3_cfg_t const usdhc1_pads[] = {
+ MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC2_PAD_CTRL),
+ MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC2_PAD_CTRL),
+ MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC2_PAD_CTRL),
+ MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC2_PAD_CTRL),
+ MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC2_PAD_CTRL),
+ MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC2_PAD_CTRL),
+ MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+ MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const ecspi4_pads[] = {
+ MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+/* only used for 4.3" display */
+static iomux_v3_cfg_t const display_pads[] = {
+ MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL),
+ MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15,
+ MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02,
+ MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03,
+ MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
+ MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
+ MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
+ MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
+ MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
+ MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
+ MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
+ MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
+ MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
+ MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
+ MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
+ MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
+ MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
+ MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
+ MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
+ MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
+ MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
+ MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
+ MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18,
+ MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19,
+ MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20,
+ MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21,
+ MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22,
+ MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23,
+};
+
+static iomux_v3_cfg_t const backlight_pads[] = {
+ /* backlight PWM brightness control */
+ MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* backlight enable */
+ MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* LCD power enable */
+ MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ if (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
+ return IMX_GPIO_NR(5, 2);
+
+ if (bus == 0 && cs == 0)
+ return IMX_GPIO_NR(4, 9);
+
+ return -1;
+}
+
+static void setup_spi(void)
+{
+ int i;
+
+ imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+ imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
+ for (i = 0; i < 4; i++)
+ enable_spi_clk(true, i);
+
+ gpio_direction_output(ECSPI1_CS0, 1);
+ gpio_direction_output(ECSPI4_CS1, 0);
+
+ /* set cs0 to high (second device on spi bus #4) */
+ gpio_direction_output(ECSPI4_CS0, 1);
+}
+
+static void setup_iomux_gpio(void)
+{
+ imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads));
+}
+
+static void setup_iomux_uart(void)
+{
+ switch (CONFIG_MXC_UART_BASE) {
+ case UART1_BASE:
+ imx_iomux_v3_setup_multiple_pads(uart1_pads,
+ ARRAY_SIZE(uart1_pads));
+ break;
+ case UART2_BASE:
+ imx_iomux_v3_setup_multiple_pads(uart2_pads,
+ ARRAY_SIZE(uart2_pads));
+ break;
+ case UART3_BASE:
+ imx_iomux_v3_setup_multiple_pads(uart3_pads,
+ ARRAY_SIZE(uart3_pads));
+ break;
+ case UART4_BASE:
+ imx_iomux_v3_setup_multiple_pads(uart4_pads,
+ ARRAY_SIZE(uart4_pads));
+ break;
+ }
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ {USDHC1_BASE_ADDR},
+ {USDHC2_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+
+#if defined(CONFIG_USE_SDHC2)
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]) |
+ fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
+#else
+ /*
+ * usdhc2 has a levelshifter on the carrier board Rev. DV1,
+ * that will automatically detect the driving direction.
+ * During initialisation this isn't working correctly,
+ * which causes DAT3 to be driven low towards the SD-card.
+ * This causes a SD-card enetring the SPI-Mode
+ * and therefore getting inaccessible until next power cycle.
+ * As workaround we drive the DAT3 line as GPIO and set it high.
+ * This makes usdhc2 unusable in u-boot, but works for the
+ * initialisation in Linux
+ */
+ imx_iomux_v3_setup_pad(MX6_PAD_SD2_DAT3__GPIO1_IO12 |
+ MUX_PAD_CTRL(NO_PAD_CTRL));
+ gpio_direction_output(IMX_GPIO_NR(1, 12) , 1);
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+#endif
+}
+#endif
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+ return 1;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ /* control data pad skew - devaddr = 0x02, register = 0x04 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+ /* rx data pad skew - devaddr = 0x02, register = 0x05 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+ /* tx data pad skew - devaddr = 0x02, register = 0x06 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+ /* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ setup_iomux_enet();
+ return cpu_eth_init(bis);
+}
+
+#if defined(CONFIG_VIDEO_IPUV3)
+
+#if defined(CONFIG_VIDEO_BMP_LOGO)
+static int rotate_logo_one(unsigned char *out, unsigned char *in)
+{
+ int i, j;
+
+ for (i = 0; i < BMP_LOGO_WIDTH; i++)
+ for (j = 0; j < BMP_LOGO_HEIGHT; j++)
+ out[j * BMP_LOGO_WIDTH + BMP_LOGO_HEIGHT - 1 - i] =
+ in[i * BMP_LOGO_WIDTH + j];
+ return 0;
+}
+
+/*
+ * Rotate the BMP_LOGO (only)
+ * Will only work, if the logo is square, as
+ * BMP_LOGO_HEIGHT and BMP_LOGO_WIDTH are defines, not variables
+ */
+void rotate_logo(int rotations)
+{
+ unsigned char out_logo[BMP_LOGO_WIDTH * BMP_LOGO_HEIGHT];
+ unsigned char *in_logo;
+ int i, j;
+
+ if (BMP_LOGO_WIDTH != BMP_LOGO_HEIGHT)
+ return;
+
+ in_logo = bmp_logo_bitmap;
+
+ /* one 90 degree rotation */
+ if (rotations == 1 || rotations == 2 || rotations == 3)
+ rotate_logo_one(out_logo, in_logo);
+
+ /* second 90 degree rotation */
+ if (rotations == 2 || rotations == 3)
+ rotate_logo_one(in_logo, out_logo);
+
+ /* third 90 degree rotation */
+ if (rotations == 3)
+ rotate_logo_one(out_logo, in_logo);
+
+ /* copy result back to original array */
+ if (rotations == 1 || rotations == 3)
+ for (i = 0; i < BMP_LOGO_WIDTH; i++)
+ for (j = 0; j < BMP_LOGO_HEIGHT; j++)
+ in_logo[i * BMP_LOGO_WIDTH + j] =
+ out_logo[i * BMP_LOGO_WIDTH + j];
+}
+#endif
+
+static void enable_display_power(void)
+{
+ imx_iomux_v3_setup_multiple_pads(backlight_pads,
+ ARRAY_SIZE(backlight_pads));
+
+ /* backlight enable */
+ gpio_direction_output(IMX_GPIO_NR(6, 31), 1);
+ /* LCD power enable */
+ gpio_direction_output(IMX_GPIO_NR(6, 15), 1);
+
+ /* enable backlight PWM 1 */
+ if (pwm_init(0, 0, 0))
+ goto error;
+ /* duty cycle 500ns, period: 3000ns */
+ if (pwm_config(0, 50000, 300000))
+ goto error;
+ if (pwm_enable(0))
+ goto error;
+ return;
+
+error:
+ puts("error init pwm for backlight\n");
+ return;
+}
+
+static void enable_lvds(struct display_info_t const *dev)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+ s32 timeout = 100000;
+
+ /* set PLL5 clock */
+ reg = readl(&ccm->analog_pll_video);
+ reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
+ writel(reg, &ccm->analog_pll_video);
+
+ /* set PLL5 to 232720000Hz */
+ reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x26);
+ reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
+ writel(reg, &ccm->analog_pll_video);
+
+ writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xC0238),
+ &ccm->analog_pll_video_num);
+ writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xF4240),
+ &ccm->analog_pll_video_denom);
+
+ reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+ writel(reg, &ccm->analog_pll_video);
+
+ while (timeout--)
+ if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+ break;
+ if (timeout < 0)
+ printf("Warning: video pll lock timeout!\n");
+
+ reg = readl(&ccm->analog_pll_video);
+ reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+ reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+ writel(reg, &ccm->analog_pll_video);
+
+ /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
+ reg = readl(&ccm->cs2cdr);
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+ reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+ | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+ writel(reg, &ccm->cs2cdr);
+
+ reg = readl(&ccm->cscmr2);
+ reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+ writel(reg, &ccm->cscmr2);
+
+ reg = readl(&ccm->chsccdr);
+ reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+ << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+ writel(reg, &ccm->chsccdr);
+
+ reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+ | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+ | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
+ | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+ | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+ | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+ | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+ writel(reg, &iomux->gpr[2]);
+
+ reg = readl(&iomux->gpr[3]);
+ reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+ | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+ << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+ writel(reg, &iomux->gpr[3]);
+
+ return;
+}
+
+static void enable_spi_display(struct display_info_t const *dev)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+ s32 timeout = 100000;
+
+#if defined(CONFIG_VIDEO_BMP_LOGO)
+ rotate_logo(3); /* portrait display in landscape mode */
+#endif
+
+ /*
+ * set ldb clock to 28341000 Hz calculated through the formula:
+ * (XRES + LEFT_M + RIGHT_M + HSYNC_LEN) *
+ * (YRES + UPPER_M + LOWER_M + VSYNC_LEN) * REFRESH)
+ * see:
+ * https://community.freescale.com/thread/308170
+ */
+ ipu_set_ldb_clock(28341000);
+
+ reg = readl(&ccm->cs2cdr);
+
+ /* select pll 5 clock */
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+ writel(reg, &ccm->cs2cdr);
+
+ /* set PLL5 to 197994996Hz */
+ reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x21);
+ reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
+ writel(reg, &ccm->analog_pll_video);
+
+ writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xfbf4),
+ &ccm->analog_pll_video_num);
+ writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xf4240),
+ &ccm->analog_pll_video_denom);
+
+ reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+ writel(reg, &ccm->analog_pll_video);
+
+ while (timeout--)
+ if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+ break;
+ if (timeout < 0)
+ printf("Warning: video pll lock timeout!\n");
+
+ reg = readl(&ccm->analog_pll_video);
+ reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+ reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+ writel(reg, &ccm->analog_pll_video);
+
+ /* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
+ reg = readl(&ccm->cs2cdr);
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+ | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+ reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+ | (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+ writel(reg, &ccm->cs2cdr);
+
+ reg = readl(&ccm->cscmr2);
+ reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+ writel(reg, &ccm->cscmr2);
+
+ reg = readl(&ccm->chsccdr);
+ reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+ << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+ reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK;
+ reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET);
+ reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK;
+ reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+ writel(reg, &ccm->chsccdr);
+
+ reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+ | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+ | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
+ | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+ | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+ | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+ | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+ writel(reg, &iomux->gpr[2]);
+
+ reg = readl(&iomux->gpr[3]);
+ reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+ | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+ << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+ writel(reg, &iomux->gpr[3]);
+
+ imx_iomux_v3_setup_multiple_pads(
+ display_pads,
+ ARRAY_SIZE(display_pads));
+
+ return;
+}
+
+struct display_info_t const displays[] = {{
+ .bus = -1,
+ .addr = 0,
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .detect = NULL,
+ .enable = enable_lvds,
+ .mode = {
+ .name = "lb07wv8",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 30066,
+ .left_margin = 88,
+ .right_margin = 88,
+ .upper_margin = 20,
+ .lower_margin = 20,
+ .hsync_len = 80,
+ .vsync_len = 5,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED
+} }, {
+ .bus = -1,
+ .addr = 0,
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .detect = NULL,
+ .enable = enable_spi_display,
+ .mode = {
+ .name = "lg4573",
+ .refresh = 60,
+ .xres = 480,
+ .yres = 800,
+ .pixclock = 37037,
+ .left_margin = 59,
+ .right_margin = 10,
+ .upper_margin = 15,
+ .lower_margin = 15,
+ .hsync_len = 10,
+ .vsync_len = 15,
+ .sync = FB_SYNC_EXT | FB_SYNC_HOR_HIGH_ACT |
+ FB_SYNC_VERT_HIGH_ACT,
+ .vmode = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+ enable_ipu_clock();
+ enable_display_power();
+}
+
+/* no console on this board */
+int board_cfb_skip(void)
+{
+ return 1;
+}
+#endif
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ setup_iomux_gpio();
+
+ gpio_direction_output(SOFT_RESET_GPIO, 1);
+ gpio_direction_output(SD2_DRIVER_ENABLE, 1);
+
+#if defined(CONFIG_VIDEO_IPUV3)
+ setup_display();
+#endif
+ return 0;
+}
+
+iomux_v3_cfg_t nfc_pads[] = {
+ MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_CS1__NAND_CE1_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD4_DAT0__NAND_DQS | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_gpmi_nand(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* config gpmi nand iomux */
+ imx_iomux_v3_setup_multiple_pads(nfc_pads,
+ ARRAY_SIZE(nfc_pads));
+
+ /* gate ENFC_CLK_ROOT clock first,before clk source switch */
+ clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+ /* config gpmi and bch clock to 100 MHz */
+ clrsetbits_le32(&mxc_ccm->cs2cdr,
+ MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+ MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
+
+ /* enable ENFC_CLK_ROOT clock */
+ setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+ /* enable gpmi and bch clock gating */
+ setbits_le32(&mxc_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
+
+ /* enable apbh clock gating */
+ setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+
+int board_init(void)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ setup_spi();
+
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
+ &i2c_pad_info1);
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
+ &i2c_pad_info2);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
+ &i2c_pad_info3);
+ setup_i2c(3, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
+ &i2c_pad_info4);
+
+ /* SPI NOR Flash read only */
+ gpio_request(CONFIG_GPIO_ENABLE_SPI_FLASH, "ena_spi_nor");
+ gpio_direction_output(CONFIG_GPIO_ENABLE_SPI_FLASH, 0);
+ gpio_free(CONFIG_GPIO_ENABLE_SPI_FLASH);
+
+ /* enable all LEDs */
+ gpio_request(IMX_GPIO_NR(2, 13), "LED ena"); /* 25 */
+ gpio_direction_output(IMX_GPIO_NR(1, 25), 0);
+
+ /* switch off Status LEDs */
+ gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */
+ gpio_direction_output(IMX_GPIO_NR(6, 16), 1);
+ gpio_request(IMX_GPIO_NR(2, 28), "LED red"); /* 60 */
+ gpio_direction_output(IMX_GPIO_NR(2, 28), 1);
+ gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */
+ gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
+ gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */
+ gpio_direction_output(IMX_GPIO_NR(2, 29), 1);
+
+ setup_gpmi_nand();
+
+ /* ENET_RX_ER for USB_OTG_ID */
+ clrsetbits_le32(&iomux->gpr[1], IOMUXC_GPR1_USB_OTG_ID_SEL_MASK, 0);
+ imx_iomux_v3_setup_multiple_pads(misc_pads, ARRAY_SIZE(misc_pads));
+
+ /* enable spi bus #2 SS drivers */
+ gpio_direction_output(IMX_GPIO_NR(6, 6), 1);
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ char *my_bootdelay;
+ char bootmode = 0;
+ char const *panel = getenv("panel");
+
+ /*
+ * Check the boot-source. If booting from NOR Flash,
+ * disable bootdelay
+ */
+ gpio_request(IMX_GPIO_NR(7, 6), "bootsel0");
+ gpio_direction_input(IMX_GPIO_NR(7, 6));
+ gpio_request(IMX_GPIO_NR(7, 7), "bootsel1");
+ gpio_direction_input(IMX_GPIO_NR(7, 7));
+ gpio_request(IMX_GPIO_NR(7, 1), "bootsel2");
+ gpio_direction_input(IMX_GPIO_NR(7, 1));
+ bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 6)) ? 1 : 0) << 0;
+ bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 7)) ? 1 : 0) << 1;
+ bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 1)) ? 1 : 0) << 2;
+
+ if (bootmode == 7) {
+ my_bootdelay = getenv("nor_bootdelay");
+ if (my_bootdelay != NULL)
+ setenv("bootdelay", my_bootdelay);
+ else
+ setenv("bootdelay", "-2");
+ }
+
+ /* if we have the lg panel, we can initialze it now */
+ if (panel)
+ if (!strcmp(panel, displays[1].mode.name))
+ lg4573_spi_startup(0, 0, 10000000, SPI_MODE_0);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: aristaitenos2\n");
+ return 0;
+}
+
+#ifdef CONFIG_USB_EHCI_MX6
+int board_ehci_hcd_init(int port)
+{
+ int ret;
+
+ ret = gpio_request(ARISTAINETOS2_USB_H1_PWR, "usb-h1-pwr");
+ if (!ret)
+ gpio_direction_output(ARISTAINETOS2_USB_H1_PWR, 1);
+ ret = gpio_request(ARISTAINETOS2_USB_OTG_PWR, "usb-OTG-pwr");
+ if (!ret)
+ gpio_direction_output(ARISTAINETOS2_USB_OTG_PWR, 1);
+ return 0;
+}
+
+int board_ehci_power(int port, int on)
+{
+ if (port)
+ gpio_set_value(ARISTAINETOS2_USB_OTG_PWR, on);
+ else
+ gpio_set_value(ARISTAINETOS2_USB_H1_PWR, on);
+ return 0;
+}
+#endif
diff --git a/board/aristainetos2/aristainetos2.cfg
b/board/aristainetos2/aristainetos2.cfg
new file mode 100644
index 0000000..a66bc1c
--- /dev/null
+++ b/board/aristainetos2/aristainetos2.cfg
@@ -0,0 +1,34 @@
+/*
+ * (C) Copyright 2014
+ * Heiko Schocher, DENX Software Engineering, h...@denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd
+ */
+BOOT_FROM spi
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch/mx6-ddr.h"
+#include "asm/arch/iomux.h"
+#include "asm/arch/crm_regs.h"
+
+#include "ddr-setup.cfg"
+#include "nt5cc256m16cp.cfg"
+#include "clocks.cfg"
+#include "axi.cfg"
diff --git a/board/aristainetos2/axi.cfg b/board/aristainetos2/axi.cfg
new file mode 100644
index 0000000..0bb816c
--- /dev/null
+++ b/board/aristainetos2/axi.cfg
@@ -0,0 +1,22 @@
+/*
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
+
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
+DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
diff --git a/board/aristainetos2/clocks.cfg b/board/aristainetos2/clocks.cfg
new file mode 100644
index 0000000..987d9a4
--- /dev/null
+++ b/board/aristainetos2/clocks.cfg
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+/* set the default clock gate to save power */
+DATA 4, CCM_CCGR0, 0x00c03f3f
+DATA 4, CCM_CCGR1, 0x0030fcff
+DATA 4, CCM_CCGR2, 0x0fffcfc0
+DATA 4, CCM_CCGR3, 0x3ff0300f
+DATA 4, CCM_CCGR4, 0xfffff300
+DATA 4, CCM_CCGR5, 0x0f0000c3
+DATA 4, CCM_CCGR6, 0x00000fff
diff --git a/board/aristainetos2/ddr-setup.cfg
b/board/aristainetos2/ddr-setup.cfg
new file mode 100644
index 0000000..3d5d894
--- /dev/null
+++ b/board/aristainetos2/ddr-setup.cfg
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+/* DDR IO TYPE */
+DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000C0000
+DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000
+/* Clock */
+DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000030
+/* Address */
+DATA 4, MX6_IOM_DRAM_CAS, 0x00000030
+DATA 4, MX6_IOM_DRAM_RAS, 0x00000030
+DATA 4, MX6_IOM_GRP_ADDDS, 0x00000030
+/* Control */
+DATA 4, MX6_IOM_DRAM_RESET, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000
+DATA 4, MX6_IOM_DRAM_SDODT0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDODT1, 0x00000030
+DATA 4, MX6_IOM_GRP_CTLDS, 0x00000030
+/* Data Strobe */
+DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000
+DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS4, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS5, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS6, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS7, 0x00000028
+DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000
+DATA 4, MX6_IOM_GRP_B0DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B1DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B2DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B3DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B4DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B5DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B6DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B7DS, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM0, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM1, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM2, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM3, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM4, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM5, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM6, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM7, 0x00000028
diff --git a/board/aristainetos2/nt5cc256m16cp.cfg
b/board/aristainetos2/nt5cc256m16cp.cfg
new file mode 100644
index 0000000..2ff41e9
--- /dev/null
+++ b/board/aristainetos2/nt5cc256m16cp.cfg
@@ -0,0 +1,60 @@
+/*
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+/* ZQ Calibration */
+DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xa1390003
+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
+/*
+ * DQS gating, read delay, write delay calibration values
+ */
+DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x42190217
+DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x017B017B
+DATA 4, MX6_MMDC_P1_MPDGCTRL0, 0x4176017B
+DATA 4, MX6_MMDC_P1_MPDGCTRL1, 0x015F016C
+DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x4C4C4D4C
+DATA 4, MX6_MMDC_P1_MPRDDLCTL, 0x4A4D4C48
+DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x3F3F3F40
+DATA 4, MX6_MMDC_P1_MPWRDLCTL, 0x3538382E
+/* read data bit delay */
+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
+/* Complete calibration by forced measurment */
+DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
+DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800
+/* in DDR3, 64-bit mode, only MMDC0 is initiated */
+DATA 4, MX6_MMDC_P0_MDPDC, 0x00020025
+DATA 4, MX6_MMDC_P0_MDOTC, 0x00333030
+DATA 4, MX6_MMDC_P0_MDCFG0, 0x676B5313
+DATA 4, MX6_MMDC_P0_MDCFG1, 0xB66E8B63
+DATA 4, MX6_MMDC_P0_MDCFG2, 0x01FF00DB
+DATA 4, MX6_MMDC_P0_MDMISC, 0x00001740
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
+DATA 4, MX6_MMDC_P0_MDRWD, 0x000026d2
+DATA 4, MX6_MMDC_P0_MDOR, 0x006B1023
+DATA 4, MX6_MMDC_P0_MDASP, 0x00000027
+DATA 4, MX6_MMDC_P0_MDCTL, 0x84190000
+
+DATA 4, MX6_MMDC_P0_MDSCR, 0x04008032
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00048031
+DATA 4, MX6_MMDC_P0_MDSCR, 0x05208030
+DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
+
+/* final ddr setup */
+DATA 4, MX6_MMDC_P0_MDREF, 0x00005800
+DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00011117
+DATA 4, MX6_MMDC_P1_MPODTCTRL, 0x00011117
+DATA 4, MX6_MMDC_P0_MDPDC, 0x00025565
+DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
diff --git a/configs/aristainetos2_defconfig b/configs/aristainetos2_defconfig
new file mode 100644
index 0000000..26292fd
--- /dev/null
+++ b/configs/aristainetos2_defconfig
@@ -0,0 +1,3 @@
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos2/aristainetos2.cfg,MX6DL"
+CONFIG_ARM=y
+CONFIG_TARGET_ARISTAINETOS2=y
diff --git a/include/configs/aristainetos2.h b/include/configs/aristainetos2.h
new file mode 100644
index 0000000..3c1203b
--- /dev/null
+++ b/include/configs/aristainetos2.h
@@ -0,0 +1,352 @@
+/*
+ * (C) Copyright 2015
+ * Heiko Schocher, DENX Software Engineering, h...@denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6DL aristainetos2 board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef __ARISTAINETOS2_CONFIG_H
+#define __ARISTAINETOS2_CONFIG_H
+
+#define CONFIG_MX6
+
+#include "mx6_common.h"
+#include <linux/sizes.h>
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+#define CONFIG_MACH_TYPE 4501
+#define CONFIG_MMCROOT "/dev/mmcblk0p1"
+#define CONFIG_HOSTNAME aristainetos2
+#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (64 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART2_BASE
+#define CONFIG_CONSOLE_DEV "ttymxc1"
+
+#define CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 0
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9031
+
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_MTD
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_MXC_SPI
+#define CONFIG_SF_DEFAULT_BUS 3
+#define CONFIG_SF_DEFAULT_CS 1
+#define CONFIG_SF_DEFAULT_SPEED 20000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_SETEXPR
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY 3
+
+#define CONFIG_LOADADDR 0x12000000
+#define CONFIG_SYS_TEXT_BASE 0x17800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=u-boot.scr\0" \
+ "fit_file=/boot/system.itb\0" \
+ "loadaddr=0x12000000\0" \
+ "fit_addr_r=0x14000000\0" \
+ "uboot=/boot/u-boot.imx\0" \
+ "uboot_sz=d0000\0" \
+ "rescue_sys_addr=f0000\0" \
+ "rescue_sys_length=f10000\0" \
+ "board_type=aristainetos2_7@1\0" \
+ "panel=lb07wv8\0" \
+ "splashpos=m,m\0" \
+ "console=" CONFIG_CONSOLE_DEV "\0" \
+ "nor_bootdelay=-2\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "mtdids=nand0=gpmi-nand,nor0=spi3.1\0" \
+ "mtdparts=mtdparts=spi3.1:832k(u-boot),64k(env),64k(env-red)," \
+ "-(rescue-system);gpmi-nand:-(ubi)\0" \
+ "addmisc=setenv bootargs ${bootargs} net.ifnames=0 consoleblank=0\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "set_fit_default=fdt addr ${fit_addr_r};fdt set /configurations " \
+ "default ${board_type}\0" \
+ "get_env=mw ${loadaddr} 0 0x20000;" \
+ "mmc rescan;" \
+ "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} env.txt;" \
+ "env import -t ${loadaddr}\0" \
+ "default_env=mw ${loadaddr} 0 0x20000;" \
+ "env export -t ${loadaddr} serial# ethaddr eth1addr " \
+ "board_type panel;" \
+ "env default -a;" \
+ "env import -t ${loadaddr}\0" \
+ "loadbootscript=" \
+ "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "mmcpart=1\0" \
+ "mmcdev=0\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs addmtd addmisc set_fit_default;" \
+ "bootm ${fit_addr_r}\0" \
+ "mmc_load_fit=ext2load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
+ "${fit_file}\0" \
+ "mmc_load_uboot=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
+ "${uboot}\0" \
+ "mmc_upd_uboot=mw.b ${loadaddr} 0xff ${uboot_sz};" \
+ "setexpr cmp_buf ${loadaddr} + ${uboot_sz};" \
+ "setexpr uboot_maxsize ${uboot_sz} - 400;" \
+ "mw.b ${cmp_buf} 0x00 ${uboot_sz};" \
+ "run mmc_load_uboot;sf probe;sf erase 0 ${uboot_sz};" \
+ "sf write ${loadaddr} 400 ${filesize};" \
+ "sf read ${cmp_buf} 400 ${uboot_sz};" \
+ "cmp.b ${loadaddr} ${cmp_buf} ${uboot_maxsize}\0" \
+ "ubiargs=setenv bootargs console=${console},${baudrate} " \
+ "ubi.mtd=0,4096 root=ubi0:rootfs rootfstype=ubifs\0 " \
+ "ubiboot=echo Booting from ubi ...; " \
+ "run ubiargs addmtd addmisc set_fit_default;" \
+ "bootm ${fit_addr_r}\0" \
+ "ubifs_load_fit=sf probe;ubi part ubi 4096;ubifsmount ubi:rootfs;" \
+ "ubifsload ${fit_addr_r} /boot/system.itb; " \
+ "imi ${fit_addr_r}\0 " \
+ "rescueargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/ram rw\0 " \
+ "rescueboot=echo Booting rescue system from NOR ...; " \
+ "run rescueargs addmtd addmisc set_fit_default;" \
+ "bootm ${fit_addr_r}\0" \
+ "rescue_load_fit=sf probe;sf read ${fit_addr_r} ${rescue_sys_addr} " \
+ "${rescue_sys_length}; imi ${fit_addr_r}\0 "
+
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev};" \
+ "if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run mmc_load_fit; then " \
+ "run mmcboot; " \
+ "else " \
+ "if run ubifs_load_fit; then " \
+ "run ubiboot; " \
+ "else " \
+ "if run rescue_load_fit; then " \
+ "run rescueboot; " \
+ "else " \
+ "echo RESCUE SYSTEM BOOT " \
+ "FAILURE;" \
+ "fi; " \
+ "fi; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "if run ubifs_load_fit; then " \
+ "run ubiboot; " \
+ "else " \
+ "if run rescue_load_fit; then " \
+ "run rescueboot; " \
+ "else " \
+ "echo RESCUE SYSTEM BOOT FAILURE;" \
+ "fi; " \
+ "fi; " \
+ "fi"
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x100000)
+#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE (12 * 1024)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SECT_SIZE (0x010000)
+#define CONFIG_ENV_OFFSET (0x0d0000)
+#define CONFIG_ENV_OFFSET_REDUND (0x0e0000)
+
+#define CONFIG_OF_LIBFDT
+
+#define CONFIG_CMD_CACHE
+
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 0x7f
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x00} }
+
+#define CONFIG_CMD_GPIO
+#define CONFIG_GPIO_ENABLE_SPI_FLASH IMX_GPIO_NR(2, 15)
+
+/* NAND stuff */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* RTC */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_RTC_BUS_NUM 2
+#define CONFIG_RTC_M41T11
+#define CONFIG_CMD_DATE
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_FAT
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+
+#define ARISTAINETOS2_USB_OTG_PWR IMX_GPIO_NR(4, 15)
+#define ARISTAINETOS2_USB_H1_PWR IMX_GPIO_NR(1, 0)
+
+/* UBI support */
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+
+#define CONFIG_MTD_UBI_FASTMAP
+#define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT 1
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+
+#define CONFIG_FIT
+
+/* Framebuffer */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+/* check this console not needed, after test remove it */
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK 198000000
+#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_SYS_LDB_CLOCK 33246000
+#define CONFIG_LG4573
+
+#define CONFIG_CMD_BMP
+
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK 66000000
+
+#endif /* __ARISTAINETOS2_CONFIG_H */
--
2.1.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
