Hi Simon,
On Mon, May 4, 2015 at 12:30 PM, Simon Glass <s...@chromium.org> wrote:
> This command was missed in the conversion. Add it back for driver model.
>
> Signed-off-by: Simon Glass <s...@chromium.org>
> ---
Reviewed-by: Joe Hershberger <joe.hershber...@ni.com>
>
> common/cmd_i2c.c | 63
> +++++++++++++++++++++++++++++++++++++++++++++++++-------
> 1 file changed, 55 insertions(+), 8 deletions(-)
>
> diff --git a/common/cmd_i2c.c b/common/cmd_i2c.c
> index ad38cbf..1bc0db8 100644
> --- a/common/cmd_i2c.c
> +++ b/common/cmd_i2c.c
> @@ -1623,6 +1623,27 @@ int do_edid(cmd_tbl_t *cmdtp, int flag, int argc, char
> *const argv[])
> }
> #endif /* CONFIG_I2C_EDID */
>
> +#ifdef CONFIG_DM_I2C
> +static void show_bus(struct udevice *bus)
> +{
> + struct udevice *dev;
> +
> + printf("Bus %d:\t%s", bus->req_seq, bus->name);
> + if (device_active(bus))
> + printf(" (active %d)", bus->seq);
> + printf("\n");
> + for (device_find_first_child(bus, &dev);
> + dev;
> + device_find_next_child(&dev)) {
> + struct dm_i2c_chip *chip = dev_get_parent_platdata(dev);
> +
> + printf(" %02x: %s, offset len %x, flags %x\n",
> + chip->chip_addr, dev->name, chip->offset_len,
> + chip->flags);
> + }
> +}
> +#endif
> +
> /**
> * do_i2c_show_bus() - Handle the "i2c bus" command-line command
> * @cmdtp: Command data struct pointer
> @@ -1632,20 +1653,30 @@ int do_edid(cmd_tbl_t *cmdtp, int flag, int argc,
> char *const argv[])
> *
> * Returns zero always.
> */
> -#if defined(CONFIG_SYS_I2C)
> +#if defined(CONFIG_SYS_I2C) || defined(CONFIG_DM_I2C)
> static int do_i2c_show_bus(cmd_tbl_t *cmdtp, int flag, int argc,
> char * const argv[])
> {
> - int i;
> -#ifndef CONFIG_SYS_I2C_DIRECT_BUS
> - int j;
> -#endif
> -
> if (argc == 1) {
> /* show all busses */
> +#ifdef CONFIG_DM_I2C
> + struct udevice *bus;
> + struct uclass *uc;
> + int ret;
> +
> + ret = uclass_get(UCLASS_I2C, &uc);
> + if (ret)
> + return CMD_RET_FAILURE;
> + uclass_foreach_dev(bus, uc)
> + show_bus(bus);
> +#else
> + int i;
> +
> for (i = 0; i < CONFIG_SYS_NUM_I2C_BUSES; i++) {
> printf("Bus %d:\t%s", i, I2C_ADAP_NR(i)->name);
> #ifndef CONFIG_SYS_I2C_DIRECT_BUS
> + int j;
> +
> for (j = 0; j < CONFIG_SYS_I2C_MAX_HOPS; j++) {
> if (i2c_bus[i].next_hop[j].chip == 0)
> break;
> @@ -1657,15 +1688,30 @@ static int do_i2c_show_bus(cmd_tbl_t *cmdtp, int
> flag, int argc,
> #endif
> printf("\n");
> }
> +#endif
> } else {
> + int i;
> +
> /* show specific bus */
> i = simple_strtoul(argv[1], NULL, 10);
> +#ifdef CONFIG_DM_I2C
> + struct udevice *bus;
> + int ret;
> +
> + ret = uclass_get_device_by_seq(UCLASS_I2C, i, &bus);
> + if (ret) {
> + printf("Invalid bus %d: err=%d\n", i, ret);
> + return CMD_RET_FAILURE;
> + }
> + show_bus(bus);
> +#else
> if (i >= CONFIG_SYS_NUM_I2C_BUSES) {
> printf("Invalid bus %d\n", i);
> return -1;
> }
> printf("Bus %d:\t%s", i, I2C_ADAP_NR(i)->name);
> #ifndef CONFIG_SYS_I2C_DIRECT_BUS
> + int j;
> for (j = 0; j < CONFIG_SYS_I2C_MAX_HOPS; j++) {
> if (i2c_bus[i].next_hop[j].chip == 0)
> break;
> @@ -1676,6 +1722,7 @@ static int do_i2c_show_bus(cmd_tbl_t *cmdtp, int flag,
> int argc,
> }
> #endif
> printf("\n");
> +#endif
> }
>
> return 0;
> @@ -1835,7 +1882,7 @@ static int do_i2c_reset(cmd_tbl_t * cmdtp, int flag,
> int argc, char * const argv
> }
>
> static cmd_tbl_t cmd_i2c_sub[] = {
> -#if defined(CONFIG_SYS_I2C)
> +#if defined(CONFIG_SYS_I2C) || defined(CONFIG_DM_I2C)
It's too bad we are already on a 3rd model for I2C and the 1st is
still kicking around. We have the same problem on the Ethernet phy
drivers as soon as I add DM support. I intend to address that one at
some point before too long... maybe even before I add DM support.
Maybe we need a deadline for this in I2C like we had for common board?
> U_BOOT_CMD_MKENT(bus, 1, 1, do_i2c_show_bus, "", ""),
> #endif
> U_BOOT_CMD_MKENT(crc32, 3, 1, do_i2c_crc, "", ""),
> @@ -1902,7 +1949,7 @@ static int do_i2c(cmd_tbl_t * cmdtp, int flag, int
> argc, char * const argv[])
> /***************************************************/
> #ifdef CONFIG_SYS_LONGHELP
> static char i2c_help_text[] =
> -#if defined(CONFIG_SYS_I2C)
> +#if defined(CONFIG_SYS_I2C) || defined(CONFIG_DM_I2C)
> "bus [muxtype:muxaddr:muxchannel] - show I2C bus info\n"
> #endif
> "crc32 chip address[.0, .1, .2] count - compute CRC32 checksum\n"
> --
> 2.2.0.rc0.207.ga3a616c
Cheers,
-Joe
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
