Hi Jagan,
On Wed, Apr 22, 2015 at 3:03 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote:
> Hi Bin,
>
> On 22 April 2015 at 12:14, Bin Meng <bmeng...@gmail.com> wrote:
>> Hi Jagan,
>>
>> On Tue, Apr 21, 2015 at 8:47 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote:
>>> Hi Bin,
>>>
>>> On 20 April 2015 at 15:02, Bin Meng <bmeng...@gmail.com> wrote:
>>>> Hi Jagan,
>>>>
>>>> On Fri, Apr 17, 2015 at 4:48 PM, Jagan Teki <jagannadh.t...@gmail.com>
>>>> wrote:
>>>>> Hi Bin,
>>>>>
>>>>> On 17 April 2015 at 07:14, Bin Meng <bmeng...@gmail.com> wrote:
>>>>>> Hi Jagan,
>>>>>>
>>>>>> On Fri, Apr 17, 2015 at 2:09 AM, Jagan Teki <jagannadh.t...@gmail.com>
>>>>>> wrote:
>>>>>>> Hi Bin,
>>>>>>>
>>>>>>> I think you have a different interpretation of sector size here-
>>>>>>>
>>>>>>> /* The size listed here is what works with SPINOR_OP_SE, which isn't
>>>>>>> * necessarily called a "sector" by the vendor.
>>>>>>> */
>>>>>>> Say for example SST25VF040B has 8 sectors of which each sector size is
>>>>>>> 64 * 1024 out of this we can use 4K sector erase or 32K sector erase or
>>>>>>> 64K sector erase through flags.
>>>>>>>
>>>>>>> Linux does follow the same-
>>>>>>> /* SST -- large erase sizes are "overlays", "sectors" are 4K */
>>>>>>> { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K |
>>>>>>> SST_WRITE) },
>>>>>>> { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K |
>>>>>>> SST_WRITE) },
>>>>>>> { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K |
>>>>>>> SST_WRITE) },
>>>>>>> { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K |
>>>>>>> SST_WRITE) },
>>>>>>>
>>>>>>> Please check it.
>>>>>>
>>>>>>
>>>>>> Yes, I know this pretty well. And I want to change this behavior, as
>>>>>> my cover letter says.
>>>>>>
>>>>>> Currently the 'sf erase' command operates on a 64KB granularity, while
>>>>>> the actual erase command is 4KB granularity, which is inconsistent and
>>>>>> causes confusion.
>>>>>
>>>>> It never related to 'sf erase' instead based on the 'params->flags'
>>>>> sf_probe will decide which erase_cmd with erase_size will use.
>>>>
>>>> No, it is related. See cmd_sf.c:
>>>
>>> I'm not getting your point- how could it erase use 64K sector size
>>> instead of 4K.
>>
>> It indeed erases 64K sector size. You need check the logic in
>> spi_flash_validate_params().
>
> We're assigning erase_size to sector_size only when SECT_4K and SECT_32K
> and for these erase_size becomes direct values, please check this.
You previous email already said: the 'sf erase' command depends on
*flash->sector_size*
> /* Compute erase sector and command */
> if (params->flags & SECT_4K) {
> flash->erase_cmd = CMD_ERASE_4K;
> flash->erase_size = 4096;
> } else if (params->flags & SECT_32K) {
> flash->erase_cmd = CMD_ERASE_32K;
> flash->erase_size = 32768;
> } else {
> flash->erase_cmd = CMD_ERASE_64K;
> flash->erase_size = flash->sector_size;
> }
Here the codes says: *flash->erase_size*
So when I give a 'sf erase 0 100' it erase 64KB even if you have SECT_4K.
>>
>>> Suppose the sector size is 4K
>>>
>>> flash->sector_size = 0x1000
>>> 1. erase 4K len flash (it's total erase length)
>>>
>>> # sf erase 0x0 0x1000
>>>
>>> len_arg = simple_strtoul(arg, &ep, 16);
>>> gives - 0x1000
>>>
>>> *len becomes 0x1000
>>>
>>> 2. erase 4K+1 len flash
>>>
>>> # sf erase 0x0 +0x1001
>>>
>>> len_arg = simple_strtoul(arg, &ep, 16);
>>> gives - 0x1001
>>>
>>> *len becomes 0x2000
>>>
>>> All the way when it goes to sf_ops.c erase will take by means of
>>> erase_size which is assigned in sf_probe.c based on flags like 4K
>>> 32K or 64K.
>
> thanks!
> --
Regards,
Bin
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
