[U-Boot] [PATCH v3] T2080QDS/PCIe: Soft Reset PCIe on T2080QDS for down-training issue

[Zhao Qiang]

T2080QDS PEX1/Slot#1 will down-train from x4 to x2,
with SRDS_PRTCL_S1 = 0x66 and SRDS_PRTCL_S2 = 0x15.
Soft reset PCIe can fix this issue.

Signed-off-by: Zhao Qiang <b45...@freescale.com>
---
changes for v2
        - modify the commit message
changes for v3
        - use CONFIG_FSL_PCIE_RESET instead of CONFIG_FSL_PCIE_T2080QDS_RESET

 drivers/pci/fsl_pci_init.c | 15 +++++++++++++++
 include/configs/T208xQDS.h |  1 +
 2 files changed, 16 insertions(+)

diff --git a/drivers/pci/fsl_pci_init.c b/drivers/pci/fsl_pci_init.c
index 231b075..152045e 100644
--- a/drivers/pci/fsl_pci_init.c
+++ b/drivers/pci/fsl_pci_init.c
@@ -444,6 +444,21 @@ void fsl_pci_init(struct pci_controller *hose, struct 
fsl_pci_info *pci_info)
                        ltssm = (in_be32(&pci->pex_csr0)
                                & PEX_CSR0_LTSSM_MASK) >> PEX_CSR0_LTSSM_SHIFT;
                        enabled = (ltssm == 0x11) ? 1 : 0;
+#ifdef CONFIG_FSL_PCIE_RESET
+                       int i;
+                       /* assert PCIe reset */
+                       setbits_be32(&pci->pdb_stat, 0x08000000);
+                       (void) in_be32(&pci->pdb_stat);
+                       udelay(1000);
+                       /* clear PCIe reset */
+                       clrbits_be32(&pci->pdb_stat, 0x08000000);
+                       asm("sync;isync");
+                       for (i = 0; i < 100 && ltssm < PCI_LTSSM_L0; i++) {
+                               pci_hose_read_config_word(hose, dev, PCI_LTSSM,
+                                                         &ltssm);
+                               udelay(1000);
+                       }
+#endif
                } else {
                /* pci_hose_read_config_word(hose, dev, PCI_LTSSM, &ltssm); */
                /* enabled = ltssm >= PCI_LTSSM_L0; */
diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index 395472b..839896a 100644
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -558,6 +558,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_PCIE2           /* PCIE controler 2 */
 #define CONFIG_PCIE3           /* PCIE controler 3 */
 #define CONFIG_PCIE4           /* PCIE controler 4 */
+#define CONFIG_FSL_PCIE_RESET
 #define CONFIG_FSL_PCI_INIT    /* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT   /* enable 64-bit PCI resources */
 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
-- 
2.1.0.27.g96db324

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot