Drop the _cyclone5 suffix from socfpga_cyclone5.c since this file
will contain Arria 5 support as well.
Signed-off-by: Marek Vasut <ma...@denx.de>
Cc: Chin Liang See <cl...@opensource.altera.com>
Acked-by: Dinh Nguyen <dingu...@opensource.altera.com>
Acked-by: Pavel Machek <pa...@denx.de>
Reviewed-by: Stefan Roese <s...@denx.de>
Cc: Vince Bridgers <vbrid...@opensource.altera.com>
---
board/altera/socfpga/Makefile | 2 +-
board/altera/socfpga/socfpga.c | 100 ++++++++++++++++++++++++++++++++
board/altera/socfpga/socfpga_cyclone5.c | 100 --------------------------------
3 files changed, 101 insertions(+), 101 deletions(-)
create mode 100644 board/altera/socfpga/socfpga.c
delete mode 100644 board/altera/socfpga/socfpga_cyclone5.c
diff --git a/board/altera/socfpga/Makefile b/board/altera/socfpga/Makefile
index 44baa00..c867f73 100644
--- a/board/altera/socfpga/Makefile
+++ b/board/altera/socfpga/Makefile
@@ -6,5 +6,5 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y := socfpga_cyclone5.o
+obj-y := socfpga.o
obj-$(CONFIG_SPL_BUILD) += pinmux_config.o iocsr_config.o
diff --git a/board/altera/socfpga/socfpga.c b/board/altera/socfpga/socfpga.c
new file mode 100644
index 0000000..459d82f
--- /dev/null
+++ b/board/altera/socfpga/socfpga.c
@@ -0,0 +1,100 @@
+/*
+ * Copyright (C) 2012 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/reset_manager.h>
+#include <asm/io.h>
+
+#include <usb.h>
+#include <usb/s3c_udc.h>
+#include <usb_mass_storage.h>
+
+#include <micrel.h>
+#include <netdev.h>
+#include <phy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Print Board information
+ */
+int checkboard(void)
+{
+ puts("BOARD: Altera SoCFPGA Cyclone5 Board\n");
+ return 0;
+}
+
+/*
+ * Initialization function which happen at early stage of c code
+ */
+int board_early_init_f(void)
+{
+ return 0;
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+int board_init(void)
+{
+ /* Address of boot parameters for ATAG (if ATAG is used) */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ return 0;
+}
+
+/*
+ * PHY configuration
+ */
+#ifdef CONFIG_PHY_MICREL_KSZ9021
+int board_phy_config(struct phy_device *phydev)
+{
+ int ret;
+ /*
+ * These skew settings for the KSZ9021 ethernet phy is required for
ethernet
+ * to work reliably on most flavors of cyclone5 boards.
+ */
+ ret = ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
+ 0x0);
+ if (ret)
+ return ret;
+
+ ret = ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
+ 0x0);
+ if (ret)
+ return ret;
+
+ ret = ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
+ 0xf0f0);
+ if (ret)
+ return ret;
+
+ if (phydev->drv->config)
+ return phydev->drv->config(phydev);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_USB_GADGET
+struct s3c_plat_otg_data socfpga_otg_data = {
+ .regs_otg = CONFIG_USB_DWC2_REG_ADDR,
+ .usb_gusbcfg = 0x1417,
+};
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+ return s3c_udc_probe(&socfpga_otg_data);
+}
+
+int g_dnl_board_usb_cable_connected(void)
+{
+ return 1;
+}
+#endif
diff --git a/board/altera/socfpga/socfpga_cyclone5.c
b/board/altera/socfpga/socfpga_cyclone5.c
deleted file mode 100644
index 459d82f..0000000
--- a/board/altera/socfpga/socfpga_cyclone5.c
+++ /dev/null
@@ -1,100 +0,0 @@
-/*
- * Copyright (C) 2012 Altera Corporation <www.altera.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/arch/reset_manager.h>
-#include <asm/io.h>
-
-#include <usb.h>
-#include <usb/s3c_udc.h>
-#include <usb_mass_storage.h>
-
-#include <micrel.h>
-#include <netdev.h>
-#include <phy.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * Print Board information
- */
-int checkboard(void)
-{
- puts("BOARD: Altera SoCFPGA Cyclone5 Board\n");
- return 0;
-}
-
-/*
- * Initialization function which happen at early stage of c code
- */
-int board_early_init_f(void)
-{
- return 0;
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-int board_init(void)
-{
- /* Address of boot parameters for ATAG (if ATAG is used) */
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
- return 0;
-}
-
-/*
- * PHY configuration
- */
-#ifdef CONFIG_PHY_MICREL_KSZ9021
-int board_phy_config(struct phy_device *phydev)
-{
- int ret;
- /*
- * These skew settings for the KSZ9021 ethernet phy is required for
ethernet
- * to work reliably on most flavors of cyclone5 boards.
- */
- ret = ksz9021_phy_extended_write(phydev,
- MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
- 0x0);
- if (ret)
- return ret;
-
- ret = ksz9021_phy_extended_write(phydev,
- MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
- 0x0);
- if (ret)
- return ret;
-
- ret = ksz9021_phy_extended_write(phydev,
- MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
- 0xf0f0);
- if (ret)
- return ret;
-
- if (phydev->drv->config)
- return phydev->drv->config(phydev);
-
- return 0;
-}
-#endif
-
-#ifdef CONFIG_USB_GADGET
-struct s3c_plat_otg_data socfpga_otg_data = {
- .regs_otg = CONFIG_USB_DWC2_REG_ADDR,
- .usb_gusbcfg = 0x1417,
-};
-
-int board_usb_init(int index, enum usb_init_type init)
-{
- return s3c_udc_probe(&socfpga_otg_data);
-}
-
-int g_dnl_board_usb_cable_connected(void)
-{
- return 1;
-}
-#endif
--
2.1.3
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
