Hi, Pavel.
It looks good to me.
If you're ok, can i suggest one thing?
On 09/05/2014 07:49 PM, Pavel Machek wrote:
>
> dw_mmc driver was responding to errors with debug(). Change that to
> prinf so that any errors are immediately obvious. Also adjust english
> in comments.
>
> Signed-off-by: Pavel Machek <pa...@denx.de>
>
> diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> index 0df30bc..4c16e7f 100644
> --- a/drivers/mmc/dw_mmc.c
> +++ b/drivers/mmc/dw_mmc.c
> @@ -177,14 +177,16 @@ static int dwmci_send_cmd(struct mmc *mmc, struct
> mmc_cmd *cmd,
> }
> }
>
> - if (i == retry)
> + if (i == retry) {
> + printf("dwmci_send_cmd: timeout..\n");
> return TIMEOUT;
> + }
>
> if (mask & DWMCI_INTMSK_RTO) {
> - debug("Response Timeout..\n");
> + printf("dwmci_send_cmd: Response Timeout..\n");
> return TIMEOUT;
> } else if (mask & DWMCI_INTMSK_RE) {
> - debug("Response Error..\n");
> + printf("dwmci_send_cmd: Response Error..\n");
> return -1;
> }
>
> @@ -204,7 +206,7 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd
> *cmd,
> do {
> mask = dwmci_readl(host, DWMCI_RINTSTS);
> if (mask & (DWMCI_DATA_ERR | DWMCI_DATA_TOUT)) {
> - debug("DATA ERROR!\n");
> + printf("dwmci_send_cmd: DATA ERROR!\n");
> return -1;
> }
> } while (!(mask & DWMCI_INTMSK_DTO));
> @@ -232,16 +234,16 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32
> freq)
> if ((freq == host->clock) || (freq == 0))
> return 0;
> /*
> - * If host->get_mmc_clk didn't define,
> + * If host->get_mmc_clk isn't defined,
> * then assume that host->bus_hz is source clock value.
> - * host->bus_hz should be set from user.
> + * host->bus_hz should be set by user.
> */
> if (host->get_mmc_clk)
> sclk = host->get_mmc_clk(host);
> else if (host->bus_hz)
> sclk = host->bus_hz;
> else {
> - printf("Didn't get source clock value..\n");
> + printf("dwmci_setup_bus: Didn't get source clock value..\n");
> return -EINVAL;
> }
>
> @@ -260,7 +262,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32
> freq)
> do {
> status = dwmci_readl(host, DWMCI_CMD);
> if (timeout-- < 0) {
> - printf("TIMEOUT error!!\n");
> + printf("dwmci_setup_bus: timeout!\n");
> return -ETIMEDOUT;
> }
> } while (status & DWMCI_CMD_START);
> @@ -275,7 +277,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32
> freq)
> do {
> status = dwmci_readl(host, DWMCI_CMD);
> if (timeout-- < 0) {
> - printf("TIMEOUT error!!\n");
> + printf("dwmci_setup_bus: timeout!\n");
According to your the main purpose, this patch is goal that noticed where/what
error is occurred.
Then i think good that add the "__LINE__".
Because there are same message like "dwmci_setup_bus: tiemout!\n" at some place.
Then i think we don't need to discuss about this patch with Marek. :)
Best Regards,
Jaehoon Chung
> return -ETIMEDOUT;
> }
> } while (status & DWMCI_CMD_START);
> @@ -290,7 +292,7 @@ static void dwmci_set_ios(struct mmc *mmc)
> struct dwmci_host *host = (struct dwmci_host *)mmc->priv;
> u32 ctype, regs;
>
> - debug("Buswidth = %d, clock: %d\n",mmc->bus_width, mmc->clock);
> + debug("Buswidth = %d, clock: %d\n", mmc->bus_width, mmc->clock);
>
> dwmci_setup_bus(host, mmc->clock);
> switch (mmc->bus_width) {
> @@ -329,7 +331,7 @@ static int dwmci_init(struct mmc *mmc)
> dwmci_writel(host, DWMCI_PWREN, 1);
>
> if (!dwmci_wait_reset(host, DWMCI_RESET_ALL)) {
> - debug("%s[%d] Fail-reset!!\n",__func__,__LINE__);
> + printf("%s[%d] Fail-reset!!\n", __func__, __LINE__);
> return -1;
> }
>
>
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
