This sub-command adds support for the RPMB partition of an eMMC: * mmc rpmb key <address of the authentication key> Programs the authentication key in the eMMC This key can not be overwritten. * mmc rpmb read <address> <block> <#count> [address of key] Reads <#count> blocks of 256 bytes in the RPMB partition beginning at block number <block>. If the optionnal address of the authentication key is provided, the Message Authentication Code (MAC) is verified on each block. * mmc rpmb write <address> <block> <#count> <address of key> Writes <#count> blocks of 256 bytes in the RPMB partition beginning at block number <block>. The datas are signed with the key provided. * mmc rpmb counter Returns the 'Write counter' of the RPMB partition.
The sub-command is conditional on compilation flag CONFIG_SUPPORT_EMMC_RPMB Signed-off-by: Pierre Aubert <[email protected]> CC: Pantelis Antoniou <[email protected]> --- README | 10 ++++ common/cmd_mmc.c | 123 +++++++++++++++++++++++++++++++++++++++++++++++++++++- 2 files changed, 132 insertions(+), 1 deletions(-) diff --git a/README b/README index 52a92e7..518e209 100644 --- a/README +++ b/README @@ -1493,6 +1493,16 @@ The following options need to be configured: CONFIG_SH_MMCIF_CLK Define the clock frequency for MMCIF + CONFIG_GENERIC_MMC + Enable the generic MMC driver + + CONFIG_SUPPORT_EMMC_BOOT + Enable some additional features of the eMMC boot partitions. + + CONFIG_SUPPORT_EMMC_RPMB + Enable the commands for reading, writing and programming the + key for the Replay Protection Memory Block partition in eMMC. + - USB Device Firmware Update (DFU) class support: CONFIG_DFU_FUNCTION This enables the USB portion of the DFU USB class diff --git a/common/cmd_mmc.c b/common/cmd_mmc.c index c1916c9..da8a243 100644 --- a/common/cmd_mmc.c +++ b/common/cmd_mmc.c @@ -130,7 +130,118 @@ U_BOOT_CMD( "display MMC info", "- display info of the current MMC device" ); +#ifdef CONFIG_SUPPORT_EMMC_RPMB +static int confirm_key_prog(void) +{ + puts("Warning: Programming authentication key can be done only once !\n" + " Use this command only if you are sure of what you are doing,\n" + "Really perform the key programming? <y/N> "); + if (confirm_yesno()) + return 1; + + puts("Authentication key programming aborted\n"); + return 0; +} +static int do_mmcrpmb(int argc, char * const argv[]) +{ + enum rpmb_state { + RPMB_INVALID, + RPMB_READ, + RPMB_WRITE, + RPMB_KEY, + RPMB_COUNTER, + } state; + struct mmc *mmc = find_mmc_device(curr_device); + void *key_addr; + char original_part; + int ret; + + state = RPMB_INVALID; + if (argc == 4 && strcmp(argv[2], "key") == 0) + state = RPMB_KEY; + if ((argc == 6 || argc == 7) && strcmp(argv[2], "read") == 0) + state = RPMB_READ; + else if (argc == 7 && strcmp(argv[2], "write") == 0) + state = RPMB_WRITE; + else if (argc == 3 && strcmp(argv[2], "counter") == 0) + state = RPMB_COUNTER; + + if (state == RPMB_INVALID) + return CMD_RET_USAGE; + if (!mmc) { + printf("no mmc device at slot %x\n", curr_device); + return CMD_RET_FAILURE; + } + mmc_init(mmc); + if (!(mmc->version & MMC_VERSION_MMC)) { + printf("It is not a EMMC device\n"); + return CMD_RET_FAILURE; + } + if (mmc->version < MMC_VERSION_4_41) { + printf("RPMB not supported before version 4.41\n"); + return CMD_RET_FAILURE; + } + /* Switch to the RPMB partition */ + original_part = mmc->part_num; + if (mmc->part_num != MMC_PART_RPMB) { + if (mmc_switch_part(curr_device, MMC_PART_RPMB) != 0) + return CMD_RET_FAILURE; + mmc->part_num = MMC_PART_RPMB; + } + ret = CMD_RET_SUCCESS; + if (state == RPMB_KEY) { + key_addr = (void *)simple_strtoul(argv[3], NULL, 16); + if (!confirm_key_prog()) + return CMD_RET_FAILURE; + if (mmc_rpmb_set_key(mmc, key_addr)) { + printf("ERROR - Key already programmed ?\n"); + ret = CMD_RET_FAILURE; + } + } else if (state == RPMB_COUNTER) { + unsigned long counter; + + if (mmc_rpmb_get_counter(mmc, &counter)) + ret = CMD_RET_FAILURE; + else + printf("Write counter= %lx\n", counter); + } else { + u16 blk, cnt; + void *addr; + int n; + + addr = (void *)simple_strtoul(argv[3], NULL, 16); + blk = simple_strtoul(argv[4], NULL, 16); + cnt = simple_strtoul(argv[5], NULL, 16); + + if (state == RPMB_READ) { + key_addr = (argc == 7) ? + (void *)simple_strtoul(argv[6], + NULL, 16) : + NULL; + n = mmc_rpmb_read(mmc, addr, blk, cnt, + key_addr); + } else { + key_addr = (void *)simple_strtoul(argv[6], + NULL, 16); + n = mmc_rpmb_write(mmc, addr, blk, cnt, + key_addr); + } + printf("%d RPMB blocks %s: %s\n", + n, argv[2], (n == cnt) ? "OK" : "ERROR"); + if (n != cnt) + ret = CMD_RET_FAILURE; + } + + /* Return to orginal partition */ + if (mmc->part_num != original_part) { + if (mmc_switch_part(curr_device, original_part) != 0) + return CMD_RET_FAILURE; + mmc->part_num = original_part; + } + return ret; +} +#endif static int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { enum mmc_state state; @@ -365,6 +476,10 @@ static int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) return mmc_set_rst_n_function(mmc, enable); #endif /* CONFIG_SUPPORT_EMMC_BOOT */ +#ifdef CONFIG_SUPPORT_EMMC_RPMB + } else if (strcmp(argv[1], "rpmb") == 0) { + return do_mmcrpmb(argc, argv); +#endif /* CONFIG_SUPPORT_EMMC_RPMB */ } else if (argc == 3 && strcmp(argv[1], "setdsr") == 0) { @@ -454,7 +569,7 @@ static int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) } U_BOOT_CMD( - mmc, 6, 1, do_mmcops, + mmc, 7, 1, do_mmcops, "MMC sub system", "read addr blk# cnt\n" "mmc write addr blk# cnt\n" @@ -474,6 +589,12 @@ U_BOOT_CMD( " - Change the RST_n_FUNCTION field of the specified device\n" " WARNING: This is a write-once field and 0 / 1 / 2 are the only valid values.\n" #endif +#ifdef CONFIG_SUPPORT_EMMC_RPMB + "mmc rpmb read addr blk# cnt [address of auth-key] - block size is 256 bytes\n" + "mmc rpmb write addr blk# cnt <address of auth-key> - block size is 256 bytes\n" + "mmc rpmb key <address of auth-key> - program the RPMB authentication key.\n" + "mmc rpmb counter - read the value of the write counter\n" +#endif "mmc setdsr - set DSR register value\n" ); #endif /* !CONFIG_GENERIC_MMC */ -- 1.7.6.5 _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
