I have this u-boot code from vizio router I can successfully compile this for AP94 target However in u-boot, network doesn't work at all Network has static IP by default and ping host in console : Using eth0 device ping failed: host 192.168.1.1 is not alive Check mii dump below, I don't see anything wrong Please help me Below link to download source http://www.mediafire.com/download/m53wqcov9v9pxhk/u-boot-1.1.4.zip
0. (1000) -- PHY control register -- (8000:0000) 0.15 = 0 reset (4000:0000) 0.14 = 0 loopback (2040:0000) 0. 6,13 = b00 speed selection = 10 Mbps (1000:1000) 0.12 = 1 A/N enable (0800:0000) 0.11 = 0 power-down (0400:0000) 0.10 = 0 isolate (0200:0000) 0. 9 = 0 restart A/N (0100:0000) 0. 8 = 0 duplex = half (0080:0000) 0. 7 = 0 collision test enable (003f:0000) 0. 5- 0 = 0 (reserved) 1. (7949) -- PHY status register -- (8000:0000) 1.15 = 0 100BASE-T4 able (4000:4000) 1.14 = 1 100BASE-X full duplex able (2000:2000) 1.13 = 1 100BASE-X half duplex able (1000:1000) 1.12 = 1 10 Mbps full duplex able (0800:0800) 1.11 = 1 10 Mbps half duplex able (0400:0000) 1.10 = 0 100BASE-T2 full duplex able (0200:0000) 1. 9 = 0 100BASE-T2 half duplex able (0100:0100) 1. 8 = 1 extended status (0080:0000) 1. 7 = 0 (reserved) (0040:0040) 1. 6 = 1 MF preamble suppression (0020:0000) 1. 5 = 0 A/N complete (0010:0000) 1. 4 = 0 remote fault (0008:0008) 1. 3 = 1 A/N able (0004:0000) 1. 2 = 0 link status (0002:0000) 1. 1 = 0 jabber detect (0001:0001) 1. 0 = 1 extended capabilities 2. (004d) -- PHY ID 1 register -- (ffff:004d) 2.15- 0 = 77 OUI portion 3. (d043) -- PHY ID 2 register -- (fc00:d000) 3.15-10 = 52 OUI portion (03f0:0040) 3. 9- 4 = 4 manufacturer part number (000f:0003) 3. 3- 0 = 3 manufacturer rev. number 4. (01e1) -- Autonegotiation advertisement register -- (8000:0000) 4.15 = 0 next page able (4000:0000) 4.14 = 0 reserved (2000:0000) 4.13 = 0 remote fault (1000:0000) 4.12 = 0 reserved (0800:0000) 4.11 = 0 asymmetric pause (0400:0000) 4.10 = 0 pause enable (0200:0000) 4. 9 = 0 100BASE-T4 able (0100:0100) 4. 8 = 1 100BASE-TX full duplex able (0080:0080) 4. 7 = 1 100BASE-TX able (0040:0040) 4. 6 = 1 10BASE-T full duplex able (0020:0020) 4. 5 = 1 10BASE-T able (001f:0001) 4. 4- 0 = 1 selector = IEEE 802.3 5. (0000) -- Autonegotiation partner abilities register -- (8000:0000) 5.15 = 0 next page able (4000:0000) 5.14 = 0 acknowledge (2000:0000) 5.13 = 0 remote fault (1000:0000) 5.12 = 0 (reserved) (0800:0000) 5.11 = 0 asymmetric pause able (0400:0000) 5.10 = 0 pause able (0200:0000) 5. 9 = 0 100BASE-T4 able (0100:0000) 5. 8 = 0 100BASE-X full duplex able (0080:0000) 5. 7 = 0 100BASE-TX able (0040:0000) 5. 6 = 0 10BASE-T full duplex able (0020:0000) 5. 5 = 0 10BASE-T able (001f:0000) 5. 4- 0 = 0 selector = ???
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
