This patch introduces CONFIG_SYS_NAND_DEVICE_WIDTH to specify bus-width of NAND
device
CONFIG_SYS_NAND_DEVICE_WIDTH == 16: NAND device with x16 bus-width
CONFIG_SYS_NAND_DEVICE_WIDTH == 8: NAND device with x8 bus-width
Need for a separate CONFIG_SYS_NAND_xx arise from following requirements:
(1) SPL NAND drivers does not have framework to parse ONFI parameter page.
(2) GPMC controller needs to know about the bus-width of device connected to it
on board.
But as GPMC controller is initialized before the NAND device is probed, and
there is no way of re-configuring the GPMC controller based on-chip ONFI
parameters.
if !defined (CONFIG_SYS_NAND_SELF_INIT)
|- board_nand_init()
|- nand_scan()
|- nand_scan_ident()
|- nand_scan_tail()
(3) Non-ONFI compliant devices need some mechanism to specify device bus-width
to driver.
Signed-off-by: Pekon Gupta <pe...@ti.com>
---
doc/README.nand | 9 +++++++++
drivers/mtd/nand/omap_gpmc.c | 13 +++++++++----
include/configs/am335x_evm.h | 1 +
include/configs/am335x_igep0033.h | 1 +
include/configs/am3517_crane.h | 1 +
include/configs/am3517_evm.h | 1 +
include/configs/cm_t335.h | 1 +
include/configs/cm_t35.h | 1 +
include/configs/devkit8000.h | 1 +
include/configs/dig297.h | 1 +
include/configs/mcx.h | 1 +
include/configs/omap3_beagle.h | 1 +
include/configs/omap3_evm_common.h | 2 +-
include/configs/omap3_igep00x0.h | 1 +
include/configs/omap3_logic.h | 1 +
include/configs/omap3_overo.h | 1 +
include/configs/omap3_pandora.h | 2 +-
include/configs/omap3_zoom1.h | 1 +
include/configs/pengwyn.h | 1 +
include/configs/siemens-am33x-common.h | 1 +
include/configs/tam3517-common.h | 1 +
include/configs/tao3530.h | 1 +
include/configs/tricorder.h | 1 +
include/configs/tseries.h | 1 +
24 files changed, 40 insertions(+), 6 deletions(-)
diff --git a/doc/README.nand b/doc/README.nand
index b91f198..90d857e 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -190,6 +190,15 @@ Configuration Options:
This is used by SoC platforms which do not have built-in ELM
hardware engine required for BCH ECC correction.
+ CONFIG_SYS_NAND_DEVICE_WIDTH
+ Specifies bus-width of the default NAND device connected to SoC.
+ This config is useful for driver which cannot self initialize or
+ parse ONFI parameter (like SPL drivers), or for supporting non-ONFI
+ compliant devices.
+ This config can take following values:
+ - 8: x8 NAND devices is connected
+ - 16: x16 NAND device is connected
+
Platform specific options
=========================
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index 881a636..2933bb9 100644
--- a/drivers/mtd/nand/omap_gpmc.c
+++ b/drivers/mtd/nand/omap_gpmc.c
@@ -805,13 +805,18 @@ int board_nand_init(struct nand_chip *nand)
nand->priv = &bch_priv;
nand->cmd_ctrl = omap_nand_hwcontrol;
nand->options |= NAND_NO_PADDING | NAND_CACHEPRG;
- /* If we are 16 bit dev, our gpmc config tells us that */
- if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000)
- nand->options |= NAND_BUSWIDTH_16;
-
nand->chip_delay = 100;
nand->ecc.layout = &omap_ecclayout;
+ /* configure driver and controller based on NAND device bus-width */
+ gpmc_config = readl(&gpmc_cfg->cs[cs].config1);
+ if (CONFIG_SYS_NAND_DEVICE_WIDTH == 16) {
+ nand->options |= NAND_BUSWIDTH_16;
+ writel(gpmc_config | (0x1 << 12), &gpmc_cfg->cs[cs].config1);
+ } else {
+ nand->options &= ~NAND_BUSWIDTH_16;
+ writel(gpmc_config & ~(0x1 << 12), &gpmc_cfg->cs[cs].config1);
+ }
/* select ECC scheme */
#if defined(CONFIG_NAND_OMAP_ECCSCHEME)
err = omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME,
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 884a42b..c95c925 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -229,6 +229,7 @@
#ifdef CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
diff --git a/include/configs/am335x_igep0033.h
b/include/configs/am335x_igep0033.h
index c17327f..0563935 100644
--- a/include/configs/am335x_igep0033.h
+++ b/include/configs/am335x_igep0033.h
@@ -245,6 +245,7 @@
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h
index 4407b45..bc38f40 100644
--- a/include/configs/am3517_crane.h
+++ b/include/configs/am3517_crane.h
@@ -329,6 +329,7 @@
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h
index 0102ff5..c57fcdd 100644
--- a/include/configs/am3517_evm.h
+++ b/include/configs/am3517_evm.h
@@ -338,6 +338,7 @@
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
diff --git a/include/configs/cm_t335.h b/include/configs/cm_t335.h
index 26b615b..158cf8f 100644
--- a/include/configs/cm_t335.h
+++ b/include/configs/cm_t335.h
@@ -142,6 +142,7 @@
#define CONFIG_CMD_NAND
#define GPMC_NAND_ECC_LP_x8_LAYOUT
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define MTDIDS_DEFAULT "nand0=nand"
#define MTDPARTS_DEFAULT "mtdparts=nand:2m(spl)," \
"1m(u-boot),1m(u-boot-env)," \
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index cfc4f9b..8bff334 100644
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -150,6 +150,7 @@
* Board NAND Info.
*/
#define CONFIG_SYS_NAND_QUIET_TEST
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index 16a00eb..8929bce 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -314,6 +314,7 @@
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
diff --git a/include/configs/dig297.h b/include/configs/dig297.h
index af6f56b..527f9c4 100644
--- a/include/configs/dig297.h
+++ b/include/configs/dig297.h
@@ -138,6 +138,7 @@
* Board NAND Info.
*/
#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
index 47244c0..3804ad4 100644
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@@ -382,6 +382,7 @@
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 0b57421..b31e907 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -422,6 +422,7 @@
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
diff --git a/include/configs/omap3_evm_common.h
b/include/configs/omap3_evm_common.h
index 7f3424b..8cf0dd0 100644
--- a/include/configs/omap3_evm_common.h
+++ b/include/configs/omap3_evm_common.h
@@ -120,7 +120,7 @@
/* Max number of NAND devices */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
/* Timeout values (in ticks) */
#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index d56d5b0..8b8583a 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -187,6 +187,7 @@
/* NAND boot config */
#ifdef CONFIG_NAND
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index 0d03c75..e4c09ff 100644
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -141,6 +141,7 @@
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_JFFS2_NAND
/* nand device jffs2 lives on */
#define CONFIG_JFFS2_DEV "nand0"
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 007e27f..66e753d 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -312,6 +312,7 @@
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index da67787..f6cd9b0 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -133,7 +133,7 @@
/* at CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
-
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#ifdef CONFIG_CMD_NAND
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_PARTITIONS
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index f0fa96e..29de928 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -140,6 +140,7 @@
/* CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_JFFS2_NAND
/* nand device jffs2 lives on */
#define CONFIG_JFFS2_DEV "nand0"
diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h
index fc25966..0a0c77f 100644
--- a/include/configs/pengwyn.h
+++ b/include/configs/pengwyn.h
@@ -127,6 +127,7 @@
#define CONFIG_CMD_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
diff --git a/include/configs/siemens-am33x-common.h
b/include/configs/siemens-am33x-common.h
index 721c4e6..3920671 100644
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -178,6 +178,7 @@
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
CONFIG_SYS_NAND_PAGE_SIZE)
diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index 3522c1a..04c4b70 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -249,6 +249,7 @@
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h
index 9c04c23..7dee34e 100644
--- a/include/configs/tao3530.h
+++ b/include/configs/tao3530.h
@@ -141,6 +141,7 @@
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 16
/* Environment information */
#define CONFIG_BOOTDELAY 3
diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index 62f97d2..4f5d066 100644
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -359,6 +359,7 @@
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
/* NAND boot config */
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
diff --git a/include/configs/tseries.h b/include/configs/tseries.h
index 8fb87ac..4c5f11a 100644
--- a/include/configs/tseries.h
+++ b/include/configs/tseries.h
@@ -158,6 +158,7 @@
#define CONFIG_NAND_OMAP_ELM
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
+#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
--
1.8.5.1.163.gd7aced9
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
