Hello all,
This is my first post here or any mailing list, so my apologies for any
mistakes.
I have added board support for the Embest Marsboard based on the imx6 dual
core chip. Embest do provide an old version of U-Boot ( 2009.08-svn8 ).
Using the current git master branch and the Wandboard and Boundry Nitrogen6x
and the original Marsboard files I have a working U-Boot. Both the eMMC and SD
card and SPI flash environment appear to be working. I seem to have problems
with networking, but have discovered the same problem with the original U-Boot
so could be my network cable.
Here are the changes from the current git master.
Date: Sat, 22 Feb 2014 12:48:06 +0000
Subject: [PATCH 1/3] add entry for Embest imx6 Marsboard
---
boards.cfg | 1 +
1 file changed, 1 insertion(+)
diff --git a/boards.cfg b/boards.cfg
index c90bb2b..d537b61 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -294,6 +294,7 @@ Active arm armv7 mx5 genesi
mx51_efikamx
Active arm armv7 mx5 genesi mx51_efikamx
mx51_efikasb
mx51_efikamx:MACH_TYPE=MACH_TYPE_MX51_EFIKASB,IMX_CONFIG=board/genesi/mx51_efikamx/imximage_sb.cfg
-
Active arm armv7 mx5 ttcontrol vision2
vision2
vision2:IMX_CONFIG=board/ttcontrol/vision2/imximage_hynix.cfg
Stefano Babic <sba...@denx.de>
Active arm armv7 mx6 - udoo
udoo_quad
udoo:IMX_CONFIG=board/udoo/udoo.cfg,MX6Q,DDR_MB=1024
Fabio Estevam <fabio.este...@freescale.com>
+Active arm armv7 mx6 embest mx6q_marsboard
mx6q_marsboard
mx6q_marsboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q.cfg,MX6Q,DDR_MB=1024
-
Active arm armv7 mx6 - wandboard
wandboard_dl
wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024
Fabio Estevam <fabio.este...@freescale.com>
Active arm armv7 mx6 - wandboard
wandboard_quad
wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q2g.cfg,MX6Q,DDR_MB=2048
Fabio Estevam <fabio.este...@freescale.com>
Active arm armv7 mx6 - wandboard
wandboard_solo
wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512
Fabio Estevam <fabio.este...@freescale.com>
--
1.8.3.2
Date: Mon, 10 Mar 2014 18:32:53 +0000
Subject: [PATCH 2/3] marsboard target files
---
board/embest/mx6q_marsboard/Makefile | 7 +
board/embest/mx6q_marsboard/mx6q_marsboard.c | 653
+++++++++++++++++++++++++++
include/configs/mx6q_marsboard.h | 418 +++++++++++++++++
3 files changed, 1078 insertions(+)
create mode 100644 board/embest/mx6q_marsboard/Makefile
create mode 100644 board/embest/mx6q_marsboard/mx6q_marsboard.c
create mode 100644 include/configs/mx6q_marsboard.h
diff --git a/board/embest/mx6q_marsboard/Makefile
b/board/embest/mx6q_marsboard/Makefile
new file mode 100644
index 0000000..c4eb0e9
--- /dev/null
+++ b/board/embest/mx6q_marsboard/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := mx6q_marsboard.o
diff --git a/board/embest/mx6q_marsboard/mx6q_marsboard.c
b/board/embest/mx6q_marsboard/mx6q_marsboard.c
new file mode 100644
index 0000000..5f39af8
--- /dev/null
+++ b/board/embest/mx6q_marsboard/mx6q_marsboard.c
@@ -0,0 +1,653 @@
+/*
+ * Copyright (C) 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sys_proto.h>
+#include <malloc.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/sata.h>
+#include <asm/imx-common/boot_mode.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <i2c.h>
+
+
+DECLARE_GLOBAL_DATA_PTR;
+#define GP_USB_OTG_PWR IMX_GPIO_NR(3, 22)
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define BUTTON_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define WEAK_PULLUP (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_SRE_SLOW)
+
+#define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_HYS | PAD_CTL_SRE_SLOW)
+
+#define OUTPUT_40OHM (PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm)
+
+
+
+#ifdef CONFIG_ARCH_MMU
+#include <asm/mmu.h>
+#include <asm/arch/mmu.h>
+#endif
+
+
+#ifdef CONFIG_IMX_UDC
+#include <usb/imx_udc.h>
+#endif
+
+#ifdef CONFIG_ANDROID_RECOVERY
+#include "../common/recovery.h"
+#include <part.h>
+#include <ext2fs.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <ubi_uboot.h>
+#include <jffs2/load_kernel.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static u32 system_rev;
+//static enum boot_device boot_dev;
+
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+ /* 4 bit bus width */
+ {"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+ {"mmc1", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+ {NULL, 0},
+};
+#endif
+
+u32 get_board_rev(void)
+{
+
+ system_rev = 0x63000;
+
+ return system_rev;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = ((ulong)CONFIG_DDR_MB * 1024 * 1024);
+
+ return 0;
+}
+
+iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart2_pads[] = {
+ MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+struct i2c_pads_info i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC,
+ .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC,
+ .gp = IMX_GPIO_NR(1, 5)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | PC,
+ .gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | PC,
+ .gp = IMX_GPIO_NR(7, 11)
+ }
+};
+
+
+static void setup_iomux_uart(void)
+{
+
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+ imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+
+ /* UART1 TXD */
+ //mxc_iomux_v3_setup_pad(MX6Q_PAD_SD3_DAT6__UART1_TXD);
+
+ /* UART1 RXD */
+ //mxc_iomux_v3_setup_pad(MX6Q_PAD_SD3_DAT7__UART1_RXD);
+
+ /* UART2 TXD */
+ //mxc_iomux_v3_setup_pad(MX6Q_PAD_EIM_D26__UART2_TXD);
+
+ /* UART2 RXD */
+ //mxc_iomux_v3_setup_pad(MX6Q_PAD_EIM_D27__UART2_RXD);
+}
+
+
+#ifdef CONFIG_MXC_SPI
+iomux_v3_cfg_t const ecspi1_pads[] = {
+ /* SS1 */
+ MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+
+void setup_spi(void)
+{
+ imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
+ ARRAY_SIZE(ecspi1_pads));
+}
+#endif
+
+
+#ifdef CONFIG_MXC_SPI_not_used
+s32 spi_get_cfg(struct imx_spi_dev_t *dev)
+{
+ switch (dev->slave.cs) {
+ case 0:
+ /* SPI-NOR */
+ dev->base = ECSPI1_BASE_ADDR;
+ dev->freq = 25000000;
+ dev->ss_pol = IMX_SPI_ACTIVE_LOW;
+ dev->ss = 0;
+ dev->fifo_sz = 64 * 4;
+ dev->us_delay = 0;
+ break;
+ case 1:
+ /* SPI-NOR */
+ dev->base = ECSPI1_BASE_ADDR;
+ dev->freq = 25000000;
+ dev->ss_pol = IMX_SPI_ACTIVE_LOW;
+ dev->ss = 1;
+ dev->fifo_sz = 64 * 4;
+ dev->us_delay = 0;
+ break;
+ default:
+ printf("Invalid Bus ID!\n");
+ }
+
+ return 0;
+}
+
+void spi_io_init(struct imx_spi_dev_t *dev)
+{
+ switch (dev->base) {
+ case ECSPI1_BASE_ADDR:
+ /* SCLK */
+ mxc_iomux_v3_setup_pad(MX6Q_PAD_EIM_D16__ECSPI1_SCLK);
+
+ /* MISO */
+ mxc_iomux_v3_setup_pad(MX6Q_PAD_EIM_D17__ECSPI1_MISO);
+
+ /* MOSI */
+ mxc_iomux_v3_setup_pad(MX6Q_PAD_EIM_D18__ECSPI1_MOSI);
+
+ if (dev->ss == 1)
+ mxc_iomux_v3_setup_pad(MX6Q_PAD_EIM_D19__ECSPI1_SS1);
+ else if(dev->ss == 0)
+ mxc_iomux_v3_setup_pad(MX6Q_PAD_EIM_EB2__ECSPI1_SS0);
+ break;
+ case ECSPI2_BASE_ADDR:
+ case ECSPI3_BASE_ADDR:
+ /* ecspi2-3 fall through */
+ break;
+ default:
+ break;
+ }
+}
+#endif
+
+
+iomux_v3_cfg_t const enet_pads1[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+
+ MX6_PAD_GPIO_0__CCM_CLKO1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+
+ /* pin 42 PHY nRST */
+ MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
+
+};
+
+iomux_v3_cfg_t const enet_pads2[] = {
+ MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+ /* phy reset: gpio3-31 */
+ gpio_direction_output(IMX_GPIO_NR(3,31), 0);
+
+ gpio_direction_output(IMX_GPIO_NR(6, 30), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
+ gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
+ imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
+ gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
+
+ udelay(1000 * 10);
+
+ gpio_direction_output(IMX_GPIO_NR(3,31), 1);
+
+ imx_iomux_v3_setup_multiple_pads(enet_pads2,ARRAY_SIZE(enet_pads2));
+
+
+
+
+}
+
+int board_eth_init(bd_t *bis)
+{
+ uint32_t base = IMX_FEC_BASE;
+ struct mii_dev *bus = NULL;
+ struct phy_device *phydev = NULL;
+ int ret;
+
+ setup_iomux_enet();
+
+#ifdef CONFIG_FEC_MXC
+ bus = fec_get_miibus(base, -1);
+ if (!bus)
+ return 0;
+ /* scan phy 4,5,6,7 */
+ phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII);
+ if (!phydev) {
+ free(bus);
+ return 0;
+ }
+ printf("using phy at %d\n", phydev->addr);
+ ret = fec_probe(bis, -1, base, bus, phydev);
+ if (ret) {
+ printf("FEC MXC: %s:failed\n", __func__);
+ free(phydev);
+ free(bus);
+ }
+#endif
+
+#ifdef CONFIG_CI_UDC
+ /* For otg ethernet*/
+ usb_eth_initialize(bis);
+#endif
+ return 0;
+}
+
+#ifdef CONFIG_CMD_MMC
+
+struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ {USDHC2_BASE_ADDR},
+ {USDHC3_BASE_ADDR},
+};
+
+#ifdef CONFIG_DYNAMIC_MMC_DEVNO
+int get_mmc_env_devno(void)
+{
+ uint soc_sbmr = readl(SRC_BASE_ADDR + 0x4);
+
+ /* BOOT_CFG2[3] and BOOT_CFG2[4] */
+ return (soc_sbmr & 0x00001800) >> 11;
+}
+#endif
+
+iomux_v3_cfg_t mx6q_usdhc1_pads[] = {
+ MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+iomux_v3_cfg_t mx6q_usdhc2_pads[] = {
+ MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t mx6q_usdhc3_pads[] = {
+ MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+iomux_v3_cfg_t mx6q_usdhc4_pads[] = {
+ MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret;
+
+ if (cfg->esdhc_base == USDHC2_BASE_ADDR) {
+ gpio_direction_input(IMX_GPIO_NR(1, 4));
+ ret = !gpio_get_value(IMX_GPIO_NR(1, 4));
+ } else {
+ // eMMC has no CD
+ ret = 1;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ s32 status = 0;
+ u32 index = 0;
+
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+ usdhc_cfg[0].max_bus_width = 4;
+ usdhc_cfg[1].max_bus_width = 4;
+
+ for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; index++) {
+ switch (index) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(
+ mx6q_usdhc2_pads, ARRAY_SIZE(mx6q_usdhc2_pads));
+
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(
+ mx6q_usdhc3_pads, ARRAY_SIZE(mx6q_usdhc3_pads));
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) then supported by the board (%d)\n",
+ index + 1, CONFIG_SYS_FSL_USDHC_NUM);
+ return status;
+ }
+ status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+ }
+
+ return status;
+}
+
+
+/* For DDR mode operation, provide target delay parameter for each SD port.
+ * Use cfg->esdhc_base to distinguish the SD port #. The delay for each port
+ * is dependent on signal layout for that particular port. If the following
+ * CONFIG is not defined, then the default target delay value will be used.
+ */
+#ifdef CONFIG_GET_DDR_TARGET_DELAY
+u32 get_ddr_delay(struct fsl_esdhc_cfg *cfg)
+{
+ /* No delay required */
+ return 0;
+}
+#endif
+
+#endif
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+ gpio_direction_output(GP_USB_OTG_PWR, 1); /* OTG power off - was 0 here
*/
+
+ return 0;
+}
+
+int board_init(void)
+{
+ struct iomuxc_base_regs *const iomuxc_regs
+ = (struct iomuxc_base_regs *)IOMUXC_BASE_ADDR;
+
+ clrsetbits_le32(&iomuxc_regs->gpr[1],
+ IOMUXC_GPR1_OTG_ID_MASK,
+ IOMUXC_GPR1_OTG_ID_GPIO1);
+
+
+ /* board id for linux */
+ gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
+
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+
+
+#ifdef CONFIG_MXC_SPI
+ setup_spi();
+#endif
+
+#ifdef CONFIG_I2C_MXC
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+#endif
+
+ return 0;
+}
+
+#ifdef CONFIG_ANDROID_RECOVERY
+struct reco_envs supported_reco_envs[BOOT_DEV_NUM] = {
+ {
+ .cmd = NULL,
+ .args = NULL,
+ },
+ {
+ .cmd = NULL,
+ .args = NULL,
+ },
+ {
+ .cmd = NULL,
+ .args = NULL,
+ },
+ {
+ .cmd = NULL,
+ .args = NULL,
+ },
+ {
+ .cmd = CONFIG_ANDROID_RECOVERY_BOOTCMD_MMC,
+ .args = CONFIG_ANDROID_RECOVERY_BOOTARGS_MMC,
+ },
+ {
+ .cmd = CONFIG_ANDROID_RECOVERY_BOOTCMD_MMC,
+ .args = CONFIG_ANDROID_RECOVERY_BOOTARGS_MMC,
+ },
+ {
+ .cmd = CONFIG_ANDROID_RECOVERY_BOOTCMD_MMC,
+ .args = CONFIG_ANDROID_RECOVERY_BOOTARGS_MMC,
+ },
+ {
+ .cmd = CONFIG_ANDROID_RECOVERY_BOOTCMD_MMC,
+ .args = CONFIG_ANDROID_RECOVERY_BOOTARGS_MMC,
+ },
+ {
+ .cmd = NULL,
+ .args = NULL,
+ },
+};
+
+int check_recovery_cmd_file(void)
+{
+ int button_pressed = 0;
+ int recovery_mode = 0;
+ u32 reg;
+
+ recovery_mode = check_and_clean_recovery_flag();
+
+ /* Check Recovery Combo Button press or not. */
+ mxc_iomux_v3_setup_pad(MX6Q_PAD_GPIO_19__GPIO_4_5);
+ reg = readl(GPIO4_BASE_ADDR + GPIO_GDIR);
+ reg &= ~(1<<5);
+ writel(reg, GPIO4_BASE_ADDR + GPIO_GDIR);
+ reg = readl(GPIO4_BASE_ADDR + GPIO_PSR);
+ if (!(reg & (1 << 5))) { /* VOL_DN key is low assert */
+ button_pressed = 1;
+ printf("Recovery key pressed\n");
+ }
+
+ return recovery_mode || button_pressed;
+}
+#endif
+
+int board_late_init(void)
+{
+ return 0;
+}
+
+
+int checkboard(void)
+{
+ puts("Board: MX6Q-MARSBOARD\n");
+
+ /*
+ switch (__REG(SRC_BASE_ADDR + 0x8)) {
+ case 0x0001:
+ printf("POR");
+ break;
+ case 0x0009:
+ printf("RST");
+ break;
+ case 0x0010:
+ case 0x0011:
+ printf("WDOG");
+ break;
+ default:
+ printf("unknown");
+ }
+ printf("]\n");
+ */
+
+ /*
+ printf("Boot Device: ");
+ switch (get_boot_device()) {
+ case WEIM_NOR_BOOT:
+ printf("NOR\n");
+ break;
+ case ONE_NAND_BOOT:
+ printf("ONE NAND\n");
+ break;
+ case PATA_BOOT:
+ printf("PATA\n");
+ break;
+ case SATA_BOOT:
+ printf("SATA\n");
+ break;
+ case I2C_BOOT:
+ printf("I2C\n");
+ break;
+ case SPI_NOR_BOOT:
+ printf("SPI NOR\n");
+ break;
+ case SD_BOOT:
+ printf("SD\n");
+ break;
+ case MMC_BOOT:
+ printf("MMC\n");
+ break;
+ case NAND_BOOT:
+ printf("NAND\n");
+ break;
+ case UNKNOWN_BOOT:
+ default:
+ printf("UNKNOWN\n");
+ break;
+ }
+ */
+ return 0;
+}
+
+#ifdef CONFIG_IMX_UDC
+
+void udc_pins_setting(void)
+{
+#define GPIO_3_22_BIT_MASK (1<<22)
+ u32 reg;
+ mxc_iomux_v3_setup_pad(MX6Q_PAD_GPIO_1__USBOTG_ID);
+ /* USB_OTG_PWR */
+ mxc_iomux_v3_setup_pad(MX6Q_PAD_EIM_D22__GPIO_3_22);
+
+ reg = readl(GPIO3_BASE_ADDR + GPIO_GDIR);
+ /* set gpio_3_22 as output */
+ reg |= GPIO_3_22_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_GDIR);
+
+ /* set USB_OTG_PWR to 0 */
+ reg = readl(GPIO3_BASE_ADDR + GPIO_DR);
+ reg &= ~GPIO_3_22_BIT_MASK;
+ writel(reg, GPIO3_BASE_ADDR + GPIO_DR);
+
+ mxc_iomux_set_gpr_register(1, 13, 1, 1);
+}
+#endif
diff --git a/include/configs/mx6q_marsboard.h b/include/configs/mx6q_marsboard.h
new file mode 100644
index 0000000..80f02a4
--- /dev/null
+++ b/include/configs/mx6q_marsboard.h
@@ -0,0 +1,418 @@
+/*
+ * Copyright (C) 2012-2013 Embest Tech, Inc.
+ *
+ * Configuration settings for the MX6Q Marsboard.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "mx6_common.h"
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+#include <asm/sizes.h>
+
+ /* High Level Configuration Options */
+#define CONFIG_ARMV7 /* This is armv7 Cortex-A9 CPU core */
+#define CONFIG_MXC
+#define CONFIG_MX6
+#define CONFIG_MX6Q_MARSBOARD
+#define CONFIG_FLASH_HEADER
+#define CONFIG_FLASH_HEADER_OFFSET 0x400
+#define CONFIG_MX6_CLK32 32768
+
+
+#define MACH_TYPE_MX6Q_MARSBOARD 3770
+#define CONFIG_MACH_TYPE MACH_TYPE_MX6Q_MARSBOARD
+
+#define CONFIG_SKIP_RELOCATE_UBOOT
+
+#define CONFIG_ARCH_CPU_INIT
+#undef CONFIG_ARCH_MMU /* disable MMU first */
+#define CONFIG_L2_OFF /* disable L2 cache first*/
+
+#define CONFIG_MX6_HCLK_FREQ 24000000
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_SYS_64BIT_VSPRINTF
+
+#define BOARD_LATE_INIT
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_REVISION_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (2 * 1024 * 1024)
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Hardware drivers
+ */
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+//#define CONFIG_CI_UDC
+#define CONFIG_USBD_HS
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_CDC
+#define CONFIG_NETCONSOLE
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART2_BASE
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
+
+/***********************************************************
+ * Command definition
+ ***********************************************************/
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 6
+#define CONFIG_PHYLIB
+
+#define CONFIG_NET_RETRY_COUNT 100
+#define CONFIG_NET_MULTI 1
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_DNS
+
+
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IMXOTP
+
+
+/* Enable below configure when supporting nand */
+
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_SF
+//#define CONFIG_CMD_ENV
+#define CONFIG_CMD_REGUL
+
+#define CONFIG_CMD_CLOCK
+#define CONFIG_REF_CLK_FREQ CONFIG_MX6_HCLK_FREQ
+
+#define CONFIG_CMD_SATA
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_IMX_DOWNLOAD_MODE
+
+#define CONFIG_BOOTDELAY 3
+
+#define CONFIG_PRIME "FEC0"
+
+#define CONFIG_LOADADDR 0x12000000 /* loadaddr env var */
+//#define CONFIG_RD_LOADADDR 0x11000000
+#define CONFIG_SYS_TEXT_BASE 0x17800000 // ??
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "console=ttymxc1\0" \
+ "splashpos=m,m\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_file=imx6q-marsboard.dtb\0" \
+ "fdt_addr=0x18000000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "mmcdev=0\0" \
+ "mmcpart=1\0" \
+ "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
+ "update_sd_firmware_filename=u-boot.imx\0" \
+ "update_sd_firmware=" \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "if mmc dev ${mmcdev}; then " \
+ "if ${get_cmd} ${update_sd_firmware_filename}; then " \
+ "setexpr fw_sz ${filesize} / 0x200; " \
+ "setexpr fw_sz ${fw_sz} + 1; " \
+ "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
+ "fi; " \
+ "fi\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "MX6Q MARSBOARD U-Boot > "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x10010000
+
+#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+#define CONFIG_FEC0_IOBASE ENET_BASE_ADDR
+#define CONFIG_FEC0_PINMUX -1
+#define CONFIG_FEC0_MIIBASE -1
+#define CONFIG_GET_FEC_MAC_ADDR_FROM_IIM
+
+#define CONFIG_MXC_FEC
+#define CONFIG_FEC0_PHY_ADDR 4
+#define CONFIG_ETH_PRIME
+#define CONFIG_RMII
+#define CONFIG_PHY_MICREL_KSZ9021
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NET
+//#define CONFIG_IPADDR 192.168.1.103
+
+/*The IP ADDRESS of SERVERIP*/
+//#define CONFIG_SERVERIP _SERVER_IP_ADDR_
+
+//#define CONFIG_NETMASK 255.255.255.0
+
+/*
+ * OCOTP Configs
+ */
+#ifdef CONFIG_CMD_IMXOTP
+ #define CONFIG_IMX_OTP
+ #define IMX_OTP_BASE OCOTP_BASE_ADDR
+ #define IMX_OTP_ADDR_MAX 0x7F
+ #define IMX_OTP_DATA_ERROR_VAL 0xBADABADA
+#endif
+
+/*
+ * I2C Configs
+ */
+#ifdef CONFIG_CMD_I2C
+ #define CONFIG_SYS_I2C
+ #define CONFIG_SYS_I2C_MXC
+ #define CONFIG_SYS_I2C_PORT I2C3_BASE_ADDR
+ #define CONFIG_SYS_I2C_SPEED 100000
+ #define CONFIG_SYS_I2C_SLAVE 0x1f
+#endif
+
+/*
+ * SPI Configs
+ */
+#ifdef CONFIG_CMD_SF
+ #define CONFIG_SPI_FLASH
+ #define CONFIG_SPI_FLASH_SST
+ #define CONFIG_MXC_SPI
+ #define CONFIG_SF_DEFAULT_BUS 0
+ #define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(2, 30)<<8))
+ #define CONFIG_SF_DEFAULT_SPEED 25000000
+ #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
+#endif
+
+/* Regulator Configs */
+#ifdef CONFIG_CMD_REGUL
+ #define CONFIG_ANATOP_REGULATOR
+ #define CONFIG_CORE_REGULATOR_NAME "vdd1p1"
+ #define CONFIG_PERIPH_REGULATOR_NAME "vdd1p1"
+#endif
+
+/*
+ * MMC Configs
+ */
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+#ifdef CONFIG_MX6Q
+#define CONFIG_CMD_SATA
+#endif
+
+/*
+ * SATA Configs
+ */
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 1
+#define CONFIG_DWC_AHSATA_PORT_ID 0
+#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+
+/*-----------------------------------------------------------------------
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */
+
+/*-----------------------------------------------------------------------
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+/*
+#define PHYS_SDRAM_1 CSD0_DDR_BASE_ADDR
+#define PHYS_SDRAM_1_SIZE (1u * 1024 * 1024 * 1024)
+#define iomem_valid_addr(addr, size) \
+ (addr >= PHYS_SDRAM_1 && addr <= (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE))
+*/
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CONFIG_SYS_NO_FLASH
+
+/* Monitor at beginning of flash */
+/* #define CONFIG_FSL_ENV_IN_MMC */
+/* #define CONFIG_FSL_ENV_IN_SATA */
+#define CONFIG_FSL_ENV_IN_SF
+
+#define CONFIG_ENV_SECT_SIZE (8 * 1024)
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+
+#if defined(CONFIG_FSL_ENV_IN_NAND)
+ #define CONFIG_ENV_IS_IN_NAND 1
+ #define CONFIG_ENV_OFFSET 0x100000
+#elif defined(CONFIG_FSL_ENV_IN_MMC)
+ #define CONFIG_ENV_IS_IN_MMC 1
+ #define CONFIG_ENV_OFFSET (768 * 1024)
+#elif defined(CONFIG_FSL_ENV_IN_SATA)
+ #define CONFIG_ENV_IS_IN_SATA 1
+ #define CONFIG_SATA_ENV_DEV 0
+ #define CONFIG_ENV_OFFSET (768 * 1024)
+#elif defined(CONFIG_FSL_ENV_IN_SF)
+ #define CONFIG_ENV_IS_IN_SPI_FLASH
+ #define CONFIG_ENV_OFFSET (768 * 1024)
+ #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
+ #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
+ #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+ #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+
+#else
+ #define CONFIG_ENV_IS_NOWHERE 1
+#endif
+#endif /* __CONFIG_H */
--
1.8.3.2
Date: Mon, 10 Mar 2014 18:48:16 +0000
Subject: [PATCH 3/3] sizes.h include path moved
---
include/configs/mx6q_marsboard.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/include/configs/mx6q_marsboard.h b/include/configs/mx6q_marsboard.h
index 80f02a4..d84fa1c 100644
--- a/include/configs/mx6q_marsboard.h
+++ b/include/configs/mx6q_marsboard.h
@@ -25,7 +25,7 @@
#include "mx6_common.h"
#include <asm/arch/imx-regs.h>
#include <asm/imx-common/gpio.h>
-#include <asm/sizes.h>
+#include <linux/sizes.h>
/* High Level Configuration Options */
#define CONFIG_ARMV7 /* This is armv7 Cortex-A9 CPU core */
--
1.8.3.2
Ben
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
