Enhance the DesignWare I2C driver to support address length more
than 1 byte. This enhancement is required as some I2C slave
device such as EEPROM chip might have 16 bit address byte.

Signed-off-by: Chin Liang See <cl...@altera.com>
Cc: Alexey Brodkin <alexey.brod...@synopsys.com>
Cc: Tom Rini <tr...@ti.com>
cc: Armando Visconti <armando.visco...@st.com>
Cc: Stefan Roese <s...@denx.de>
Cc: Albert ARIBAUD <albert.u.b...@aribaud.net>
Cc: Heiko Schocher <h...@denx.de>
Cc: Vipin KUMAR <vipin.ku...@st.com>
Cc: Tom Rix <tom....@windriver.com>
Cc: Mischa Jonker <mjon...@synopsys.com>
---
 drivers/i2c/designware_i2c.c |   24 +++++++++---------------
 1 file changed, 9 insertions(+), 15 deletions(-)

diff --git a/drivers/i2c/designware_i2c.c b/drivers/i2c/designware_i2c.c
index cb2ac04..c0ac5f7 100644
--- a/drivers/i2c/designware_i2c.c
+++ b/drivers/i2c/designware_i2c.c
@@ -205,27 +205,21 @@ static int check_params(uint addr, int alen, uchar 
*buffer, int len)
                return 1;
        }
 
-       if (alen > 1) {
-               printf("addr len %d not supported\n", alen);
-               return 1;
-       }
-
-       if (addr + len > 256) {
-               printf("address out of range\n");
-               return 1;
-       }
-
        return 0;
 }
 
-static int i2c_xfer_init(uchar chip, uint addr)
+static int i2c_xfer_init(uchar chip, uint addr, int alen)
 {
        if (i2c_wait_for_bb())
                return 1;
 
        i2c_setaddress(chip);
-       writel(addr, &i2c_regs_p->ic_cmd_data);
-
+       while (alen) {
+               alen--;
+               /* high byte address going out first */
+               writel((addr >> (alen * 8)) & 0xff,
+                       &i2c_regs_p->ic_cmd_data);
+       }
        return 0;
 }
 
@@ -269,7 +263,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar 
*buffer, int len)
        if (check_params(addr, alen, buffer, len))
                return 1;
 
-       if (i2c_xfer_init(chip, addr))
+       if (i2c_xfer_init(chip, addr, alen))
                return 1;
 
        start_time_rx = get_timer(0);
@@ -310,7 +304,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar 
*buffer, int len)
        if (check_params(addr, alen, buffer, len))
                return 1;
 
-       if (i2c_xfer_init(chip, addr))
+       if (i2c_xfer_init(chip, addr, alen))
                return 1;
 
        start_time_tx = get_timer(0);
-- 
1.7.9.5


_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to