On 08/28/2013 07:04 AM, Valentin Longchamp wrote: > This patch introduces the support for Keymile's kmp204x reference > design. This design is based on Freescale's P2040/P2041 SoC. > > The peripherals used by this design are: > - DDR3 RAM with SPD support > - SPI NOR Flash as boot medium > - NAND Flash > - 2 PCIe busses (hosts 1 and 3) > - 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5) > - 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt > FPGA > - 2 HW I2C busses > - last but not least, the mandatory serial port > > The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb > support and was changed according to our design (that means essentially > removing what is not present on the designs and a few adaptations). > > There is currently only one prototype board that is based on this design > and this patch also introduces it. The board is called kmlion1. > > Signed-off-by: Stefan Bigler <stefan.big...@keymile.com> > Signed-off-by: Valentin Longchamp <valentin.longch...@keymile.com> > --- > Changes in v2: > - Remove patch "5/8 fsl: do not define FSL_SRIO_PCIE_BOOT_MASTER for all > P2041 systems" from the series as it is not needed with current u-boot. > - fix the defines used in kmp204x/law.c for the lbus local address > windows. > - fix the header files to include Freescale's copyrights > - integrate Scott's feedback > > MAINTAINERS | 1 + > board/keymile/kmp204x/Makefile | 48 ++++ > board/keymile/kmp204x/ddr.c | 80 ++++++ > board/keymile/kmp204x/eth.c | 87 +++++++ > board/keymile/kmp204x/kmp204x.c | 285 +++++++++++++++++++++ > board/keymile/kmp204x/kmp204x.h | 31 +++ > board/keymile/kmp204x/law.c | 56 +++++ > board/keymile/kmp204x/pbi.cfg | 51 ++++ > board/keymile/kmp204x/pci.c | 51 ++++ > board/keymile/kmp204x/rcw_kmp204x.cfg | 11 + > board/keymile/kmp204x/tlb.c | 126 ++++++++++ > boards.cfg | 1 + > include/configs/km/kmp204x-common.h | 462 > ++++++++++++++++++++++++++++++++++ > include/configs/kmp204x.h | 84 +++++++ > 14 files changed, 1374 insertions(+) > create mode 100644 board/keymile/kmp204x/Makefile > create mode 100644 board/keymile/kmp204x/ddr.c > create mode 100644 board/keymile/kmp204x/eth.c > create mode 100644 board/keymile/kmp204x/kmp204x.c > create mode 100644 board/keymile/kmp204x/kmp204x.h > create mode 100644 board/keymile/kmp204x/law.c > create mode 100644 board/keymile/kmp204x/pbi.cfg > create mode 100644 board/keymile/kmp204x/pci.c > create mode 100644 board/keymile/kmp204x/rcw_kmp204x.cfg > create mode 100644 board/keymile/kmp204x/tlb.c > create mode 100644 include/configs/km/kmp204x-common.h > create mode 100644 include/configs/kmp204x.h > > diff --git a/MAINTAINERS b/MAINTAINERS > index 081cf96..fff77f0 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -778,6 +778,7 @@ Valentin Longchamp <valentin.longch...@keymile.com> > mgcoge3un ARM926EJS (Kirkwood SoC) > kmcoge5un ARM926EJS (Kirkwood SoC) > portl2 ARM926EJS (Kirkwood SoC) > + kmcoge4 MPC85xx (P2041 SoC) >
Do you mean "kmlion1" instead of "kmcoge4" here? See below boards.cfg file. <snip> > --- a/boards.cfg > +++ b/boards.cfg > @@ -744,6 +744,7 @@ tuge1 powerpc mpc83xx > km83xx keymile > tuxx1 powerpc mpc83xx km83xx > keymile - tuxx1:TUXX1 > kmopti2 powerpc mpc83xx km83xx > keymile - tuxx1:KMOPTI2 > kmsupx5 powerpc mpc83xx km83xx > keymile - tuxx1:KMSUPX5 > +kmlion1 powerpc mpc85xx kmp204x > keymile - kmp204x:KMLION1 > sbc8548 powerpc mpc85xx sbc8548 - > - sbc8548 > sbc8548_PCI_33 powerpc mpc85xx sbc8548 - > - sbc8548:PCI,33 > sbc8548_PCI_33_PCIE powerpc mpc85xx sbc8548 - > - sbc8548:PCI,33,PCIE No need to resend this patch. I need to fix it for the new boards.cfg format anyway. Just need your confirmation. York _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
