Instead of duplicating HDMI setup code for every mx6 board, factor out the
common code
Signed-off-by: Pardeep Kumar Singla <b45...@freescale.com>
---
arch/arm/cpu/armv7/mx6/soc.c | 51 ++++++++++++++
arch/arm/include/asm/arch-mx6/mxc_hdmi.h | 6 ++
arch/arm/include/asm/arch-mx6/sys_proto.h | 13 ++++
board/boundary/nitrogen6x/nitrogen6x.c | 57 +---------------
board/freescale/mx6qsabrelite/mx6qsabrelite.c | 60 ++--------------
board/wandboard/wandboard.c | 91 ++++++-------------------
include/configs/mx6qsabrelite.h | 8 ++-
include/configs/nitrogen6x.h | 2 +-
include/configs/wandboard.h | 1 +
9 files changed, 106 insertions(+), 183 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index fc436fb..6e79310 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -32,6 +32,8 @@
#include <asm/imx-common/boot_mode.h>
#include <asm/imx-common/dma.h>
#include <stdbool.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
struct scu_regs {
u32 ctrl;
@@ -228,3 +230,52 @@ const struct boot_mode soc_boot_modes[] = {
void s_init(void)
{
}
+
+#ifdef CONFIG_IMX_HDMI
+void imx_enable_hdmi_phy(struct display_info_t const *dev)
+{
+ struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+ u8 reg;
+ reg = readb(&hdmi->phy_conf0);
+ reg |= HDMI_PHY_CONF0_PDZ_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ udelay(3000);
+ reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ udelay(3000);
+ reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
+}
+
+void imx_setup_hdmi(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+ int reg;
+
+ /* Turn on IPU clock */
+ reg = readl(&mxc_ccm->CCGR3);
+ reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET;
+ writel(reg, &mxc_ccm->CCGR3);
+
+ /* Turn on HDMI PHY clock */
+ reg = readl(&mxc_ccm->CCGR2);
+ reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK|
+ MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
+ writel(reg, &mxc_ccm->CCGR2);
+ /* clear HDMI PHY reset */
+ writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
+ reg = readl(&mxc_ccm->chsccdr);
+ reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK|
+ MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK|
+ MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
+ reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+ << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)|
+ (CHSCCDR_PODF_DIVIDE_BY_3
+ << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
+ |(CHSCCDR_IPU_PRE_CLK_540M_PFD
+ << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+ writel(reg, &mxc_ccm->chsccdr);
+}
+#endif
diff --git a/arch/arm/include/asm/arch-mx6/mxc_hdmi.h
b/arch/arm/include/asm/arch-mx6/mxc_hdmi.h
index 9dccb3f..9e2074b 100644
--- a/arch/arm/include/asm/arch-mx6/mxc_hdmi.h
+++ b/arch/arm/include/asm/arch-mx6/mxc_hdmi.h
@@ -21,6 +21,12 @@
#ifndef __MXC_HDMI_H__
#define __MXC_HDMI_H__
+#ifdef CONFIG_IMX_HDMI
+#include<asm/arch/sys_proto.h>
+void imx_enable_hdmi_phy(struct display_info_t const *dev);
+void imx_setup_hdmi(void);
+#endif
+
/*
* Hdmi controller registers
*/
diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h
b/arch/arm/include/asm/arch-mx6/sys_proto.h
index 38e4e51..9fb539b 100644
--- a/arch/arm/include/asm/arch-mx6/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx6/sys_proto.h
@@ -25,6 +25,9 @@
#define _SYS_PROTO_H_
#include <asm/imx-common/regs-common.h>
+#include<linux/list.h>
+#include <linux/fb.h>
+#include <i2c.h>
#define MXC_CPU_MX51 0x51
#define MXC_CPU_MX53 0x53
@@ -34,6 +37,16 @@
#define MXC_CPU_MX6Q 0x63
#define is_soc_rev(rev) ((get_cpu_rev() & 0xFF) - rev)
+
+struct display_info_t {
+ int bus;
+ int addr;
+ int pixfmt;
+ int (*detect)(struct display_info_t const *dev);
+ void (*enable)(struct display_info_t const *dev);
+ struct fb_videomode mode;
+};
+
u32 get_cpu_rev(void);
const char *get_imx_type(u32 imxtype);
unsigned imx_ddr_size(void);
diff --git a/board/boundary/nitrogen6x/nitrogen6x.c
b/board/boundary/nitrogen6x/nitrogen6x.c
index 8f0f9b8..d97d47a 100644
--- a/board/boundary/nitrogen6x/nitrogen6x.c
+++ b/board/boundary/nitrogen6x/nitrogen6x.c
@@ -464,40 +464,12 @@ static iomux_v3_cfg_t const rgb_pads[] = {
MX6_PAD_DISP0_DAT23__IPU1_DISP0_DAT_23,
};
-struct display_info_t {
- int bus;
- int addr;
- int pixfmt;
- int (*detect)(struct display_info_t const *dev);
- void (*enable)(struct display_info_t const *dev);
- struct fb_videomode mode;
-};
-
-
static int detect_hdmi(struct display_info_t const *dev)
{
struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
return readb(&hdmi->phy_stat0) & HDMI_PHY_HPD;
}
-static void enable_hdmi(struct display_info_t const *dev)
-{
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
- u8 reg;
- printf("%s: setup HDMI monitor\n", __func__);
- reg = readb(&hdmi->phy_conf0);
- reg |= HDMI_PHY_CONF0_PDZ_MASK;
- writeb(reg, &hdmi->phy_conf0);
-
- udelay(3000);
- reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
- writeb(reg, &hdmi->phy_conf0);
- udelay(3000);
- reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
- writeb(reg, &hdmi->phy_conf0);
- writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
-}
-
static int detect_i2c(struct display_info_t const *dev)
{
return ((0 == i2c_set_bus_num(dev->bus))
@@ -528,7 +500,7 @@ static struct display_info_t const displays[] = {{
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_hdmi,
- .enable = enable_hdmi,
+ .enable = imx_enable_hdmi_phy,
.mode = {
.name = "HDMI",
.refresh = 60,
@@ -653,25 +625,14 @@ static void setup_display(void)
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-
int reg;
+ imx_setup_hdmi();
/* Turn on LDB0,IPU,IPU DI0 clocks */
reg = __raw_readl(&mxc_ccm->CCGR3);
- reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET
- |MXC_CCM_CCGR3_LDB_DI0_MASK;
+ reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
writel(reg, &mxc_ccm->CCGR3);
- /* Turn on HDMI PHY clock */
- reg = __raw_readl(&mxc_ccm->CCGR2);
- reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK
- |MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
- writel(reg, &mxc_ccm->CCGR2);
-
- /* clear HDMI PHY reset */
- writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
-
/* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */
writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr);
writel(0x13<<ANATOP_PFD_480_PFD1_FRAC_SHIFT, &anatop->pfd_480_set);
@@ -688,18 +649,6 @@ static void setup_display(void)
reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
writel(reg, &mxc_ccm->cscmr2);
- reg = readl(&mxc_ccm->chsccdr);
- reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
- |MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
- |MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
- reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
- |(CHSCCDR_PODF_DIVIDE_BY_3
- <<MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
- |(CHSCCDR_IPU_PRE_CLK_540M_PFD
- <<MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
- writel(reg, &mxc_ccm->chsccdr);
-
reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
|IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
|IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
index 862bc30..21b6bb6 100644
--- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
+++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
@@ -42,7 +42,7 @@
#include <asm/arch/crm_regs.h>
#include <asm/arch/mxc_hdmi.h>
#include <i2c.h>
-
+#include<asm/arch/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
@@ -436,40 +436,12 @@ static iomux_v3_cfg_t const rgb_pads[] = {
MX6_PAD_DISP0_DAT23__IPU1_DISP0_DAT_23,
};
-struct display_info_t {
- int bus;
- int addr;
- int pixfmt;
- int (*detect)(struct display_info_t const *dev);
- void (*enable)(struct display_info_t const *dev);
- struct fb_videomode mode;
-};
-
-
static int detect_hdmi(struct display_info_t const *dev)
{
struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
return readb(&hdmi->phy_stat0) & HDMI_PHY_HPD;
}
-static void enable_hdmi(struct display_info_t const *dev)
-{
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
- u8 reg;
- printf("%s: setup HDMI monitor\n", __func__);
- reg = readb(&hdmi->phy_conf0);
- reg |= HDMI_PHY_CONF0_PDZ_MASK;
- writeb(reg, &hdmi->phy_conf0);
-
- udelay(3000);
- reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
- writeb(reg, &hdmi->phy_conf0);
- udelay(3000);
- reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
- writeb(reg, &hdmi->phy_conf0);
- writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
-}
-
static int detect_i2c(struct display_info_t const *dev)
{
return ((0 == i2c_set_bus_num(dev->bus))
@@ -500,7 +472,7 @@ static struct display_info_t const displays[] = {{
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_hdmi,
- .enable = enable_hdmi,
+ .enable = imx_enable_hdmi_phy,
.mode = {
.name = "HDMI",
.refresh = 60,
@@ -625,25 +597,15 @@ static void setup_display(void)
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
-
int reg;
+ imx_setup_hdmi();
+
/* Turn on LDB0,IPU,IPU DI0 clocks */
reg = __raw_readl(&mxc_ccm->CCGR3);
- reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET
- |MXC_CCM_CCGR3_LDB_DI0_MASK;
+ reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
writel(reg, &mxc_ccm->CCGR3);
- /* Turn on HDMI PHY clock */
- reg = __raw_readl(&mxc_ccm->CCGR2);
- reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK
- |MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
- writel(reg, &mxc_ccm->CCGR2);
-
- /* clear HDMI PHY reset */
- writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
-
/* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */
writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr);
writel(0x13<<ANATOP_PFD_480_PFD1_FRAC_SHIFT, &anatop->pfd_480_set);
@@ -660,18 +622,6 @@ static void setup_display(void)
reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
writel(reg, &mxc_ccm->cscmr2);
- reg = readl(&mxc_ccm->chsccdr);
- reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
- |MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
- |MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
- reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
- |(CHSCCDR_PODF_DIVIDE_BY_3
- <<MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
- |(CHSCCDR_IPU_PRE_CLK_540M_PFD
- <<MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
- writel(reg, &mxc_ccm->chsccdr);
-
reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
|IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
|IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index 43c02ac..4957303 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -28,7 +28,6 @@
#include <miiphy.h>
#include <netdev.h>
#include <linux/fb.h>
-
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
@@ -211,85 +210,37 @@ int board_phy_config(struct phy_device *phydev)
}
#if defined(CONFIG_VIDEO_IPUV3)
-static void enable_hdmi(void)
-{
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
- u8 reg;
- reg = readb(&hdmi->phy_conf0);
- reg |= HDMI_PHY_CONF0_PDZ_MASK;
- writeb(reg, &hdmi->phy_conf0);
-
- udelay(3000);
- reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
- writeb(reg, &hdmi->phy_conf0);
- udelay(3000);
- reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
- writeb(reg, &hdmi->phy_conf0);
- writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
-}
-
-static struct fb_videomode const hdmi = {
- .name = "HDMI",
- .refresh = 60,
- .xres = 1024,
- .yres = 768,
- .pixclock = 15385,
- .left_margin = 220,
- .right_margin = 40,
- .upper_margin = 21,
- .lower_margin = 7,
- .hsync_len = 60,
- .vsync_len = 10,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-};
+static struct display_info_t const displays = {
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .enable = imx_enable_hdmi_phy,
+ .mode = {
+ .name = "HDMI",
+ .refresh = 60,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 15385,
+ .left_margin = 220,
+ .right_margin = 40,
+ .upper_margin = 21,
+ .lower_margin = 7,
+ .hsync_len = 60,
+ .vsync_len = 10,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED
+} };
int board_video_skip(void)
{
int ret;
- ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24);
+ ret = ipuv3_fb_init(&displays.mode, 0, displays.pixfmt);
if (ret)
printf("HDMI cannot be configured: %d\n", ret);
-
- enable_hdmi();
+ displays.enable(&displays);
return ret;
}
-
-static void setup_display(void)
-{
- struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
- int reg;
-
- /* Turn on IPU clock */
- reg = readl(&mxc_ccm->CCGR3);
- reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET;
- writel(reg, &mxc_ccm->CCGR3);
-
- /* Turn on HDMI PHY clock */
- reg = readl(&mxc_ccm->CCGR2);
- reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK
- | MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
- writel(reg, &mxc_ccm->CCGR2);
-
- /* clear HDMI PHY reset */
- writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
-
- reg = readl(&mxc_ccm->chsccdr);
- reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK
- | MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK
- | MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
- reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)
- | (CHSCCDR_PODF_DIVIDE_BY_3
- << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
- | (CHSCCDR_IPU_PRE_CLK_540M_PFD
- << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
- writel(reg, &mxc_ccm->chsccdr);
-}
#endif /* CONFIG_VIDEO_IPUV3 */
int board_eth_init(bd_t *bis)
@@ -309,7 +260,7 @@ int board_early_init_f(void)
{
setup_iomux_uart();
#if defined(CONFIG_VIDEO_IPUV3)
- setup_display();
+ imx_setup_hdmi();
#endif
return 0;
}
diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h
index c7db81d..4549f24 100644
--- a/include/configs/mx6qsabrelite.h
+++ b/include/configs/mx6qsabrelite.h
@@ -26,6 +26,7 @@
#define CONFIG_MX6Q
#include "mx6_common.h"
+#include<asm/sizes.h>
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
@@ -35,14 +36,14 @@
#include <asm/arch/imx-regs.h>
#include <asm/imx-common/gpio.h>
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
+
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
-
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_MISC_INIT_R
#define CONFIG_MXC_GPIO
@@ -141,6 +142,7 @@
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_LOGO
#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_IMX_HDMI
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h
index 74df66c..5a4d06e 100644
--- a/include/configs/nitrogen6x.h
+++ b/include/configs/nitrogen6x.h
@@ -154,7 +154,7 @@
#define CONFIG_IPUV3_CLK 260000000
#define CONFIG_CMD_HDMIDETECT
#define CONFIG_CONSOLE_MUX
-
+#define CONFIG_IMX_HDMI
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
index ee6bf21..9282e23 100644
--- a/include/configs/wandboard.h
+++ b/include/configs/wandboard.h
@@ -100,6 +100,7 @@
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_IMX_HDMI
#if defined(CONFIG_MX6DL)
#define CONFIG_DEFAULT_FDT_FILE "imx6dl-wandboard.dtb"
--
1.7.9.5
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
