I am trying to upgrade U-Boot on a Glomation GESBC-9G20 (a derivative of the Atmel AT91SAM9G20-EK) to a version that supports UBIFS. The latest U-Boot does not work. (See also my report on the Glomation user forum, http://glomation.net/smf/index.php/topic,1389.0.html.)
The GESBC-9G20 comes with a patched U-Boot 1.3.4. I built U-Boot 1.3.4 with Glomation patches using both the Glomation ARM cross development tool chain and the Code Sourcery 2013.05 ARM EABI cross development tool chain. Both work fine. I built the latest U-Boot release (2013.04) and the U-Boot git tree (2013.07 preview) version using the Code Sourcery tool chain (the Glomation tool chain is too old). Neither work. They both hang at: ˇRomBOOT Start AT91Bootstrap... In topic http://glomation.net/smf/index.php/topic,1382.0.html, it says the latest U-Boot supports the AT91SAM9G20. That seems to be true for an Atmel AT91SAM9G20-EK. But, U-Boot built for an AT91SAM9G20-EK does not seem to work on my GESBC-9G20. Glomation's response about the differences: The GESBC-9G20 is a slimmed down version of the Atmel AT91SAM9G20-ek (the earlier version with 1 SD card slot). The audio, serial EEPROM, etc were omitted. The binary code (bootstrap, U-Boot, kernel) from Atmel can run directly on the GESBC-9G20. As far as I can tell from the SAM-BA download log file, U-Boot fits in its flash partition: <snip> -I- === Erase all the NAND flash blocs and test the erasing === -I- GENERIC::EraseAll -I- === Load the bootstrap: nandflash_at91sam9-ek in the first sector === GENERIC::SendFile nandflash_at91sam9g20ek.bin at address 0x0 -I- File size : 0x1078 byte(s) -I- Complete 0% -I- Writing: 0x1078 bytes at 0x0 (buffer addr : 0x20003E38) -I- 0x1078 bytes written by applet -I- === Load the u-boot in the next sectors === -I- Send File u-boot-2013.07-git.bin at address 0x00020000 GENERIC::SendFile u-boot-2013.07-git.bin at address 0x20000 -I- File size : 0x3E054 byte(s) -I- Complete 0% -I- Writing: 0x20000 bytes at 0x20000 (buffer addr : 0x20003E38) -I- 0x20000 bytes written by applet -I- Complete 51% -I- Writing: 0x1E054 bytes at 0x40000 (buffer addr : 0x20003E38) -I- 0x1E054 bytes written by applet -I- === Load the u-boot environment variables === -I- Send File ubootEnvtFileNandFlash.bin at address 0x00060000 GENERIC::SendFile ubootEnvtFileNandFlash.bin at address 0x60000 -I- File size : 0x20000 byte(s) -I- Complete 0% -I- Writing: 0x20000 bytes at 0x60000 (buffer addr : 0x20003E38) -I- 0x20000 bytes written by applet -I- === Load the Kernel image === -I- Send File uImage-3.2.6 at address 0x00100000 GENERIC::SendFile uImage-3.2.6 at address 0x100000 <snip> -I- === Load the linux file system === -I- Send File 9260rootfs.img at address 0x00400000 GENERIC::SendFile 9260rootfs.img at address 0x400000 <snip> I could use some guidance to track down the problem. Larry Baker US Geological Survey 650-329-5608 ba...@usgs.gov Below are the steps I followed (plus, I ran SAM-BA under Windows 8 to write the bootstrap, u-boot, kernel, and rootfs to flash memory): • Download and build U-Boot 1.3.4 with Glomation patches using the Glomation ARM cross development tool chain. $ mkdir -p /opt/gesbc-9g20/u-boot $ cd /opt/gesbc-9g20/u-boot $ wget http://ftp.denx.de/pub/u-boot/u-boot-1.3.4.tar.bz2 Download u-boot-1.3.4-exp.5.diff from the Glomation user forum topic, reply #1, at http://glomation.net/smf/index.php/topic,1389.0.html $ tar -xjf u-boot-1.3.4.tar.bz2 $ cd u-boot-1.3.4 $ patch -p1 < ../u-boot-1.3.4-exp.5.diff $ make ARCH=arm CROSS_COMPILE=arm-unknown-linux-gnu- at91sam9g20ek_nandflash_config $ make ARCH=arm CROSS_COMPILE=arm-unknown-linux-gnu- $ cp u-boot.bin /opt/gesbc-9g20/u-boot-1.3.4.bin • Repeat the build using the Code Sourcery ARM cross development tool chain. $ cd /opt/gesbc-9g20/u-boot/u-boot-1.3.4 $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- distclean $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- at91sam9g20ek_nandflash_config $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- $ cp u-boot.bin /opt/gesbc-9g20/u-boot-1.3.4.bin • Download and build the latest U-Boot stable release using the Code Sourcery ARM cross development tool chain. $ cd /opt/u-boot $ wget http://ftp.denx.de/pub/u-boot/u-boot-latest.tar.bz2 $ tar -xjf u-boot-latest.tar.bz2 $ cd u-boot-2013.04 $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- distclean $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- at91sam9g20ek_nandflash_config $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- $ cp u-boot.bin /opt/gesbc-9g20/u-boot-2013.04.bin • Download and build the latest U-Boot development tree using the Code Sourcery ARM cross development tool chain. $ cd /opt/u-boot $ git clone git://git.denx.de/u-boot.git $ cd u-boot $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- distclean $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- at91sam9g20ek_nandflash_config $ make ARCH=arm CROSS_COMPILE=arm-none-eabi- $ cp u-boot.bin /opt/gesbc-9g20/u-boot-2013.07-git.bin _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
