Dear Thierry Reding,
> On Sun, Jun 16, 2013 at 10:48:45PM +0200, Marek Vasut wrote:
> > Dear Thierry Reding,
> >
> > > On Sat, Jun 15, 2013 at 11:28:25PM +0200, Marek Vasut wrote:
> > > > Dear Thierry Reding,
> > > >
> > > > > On Fri, Jun 14, 2013 at 06:41:40PM +0800, Jim Lin wrote:
> > > > > [...]
> > > > >
> > > > > > diff --git a/board/nvidia/dts/tegra30-beaver.dts
> > > > > > b/board/nvidia/dts/tegra30-beaver.dts
> > > > >
> > > > > [...]
> > > > >
> > > > > > @@ -68,4 +69,9 @@
> > > > > >
> > > > > > status = "okay";
> > > > > > bus-width = <8>;
> > > > > >
> > > > > > };
> > > > > >
> > > > > > +
> > > > > > + usb@7d008000 {
> > > > > > + nvidia,vbus-gpio = <&gpio 61 3>; /* PH5,
> >
> > USB13_VBUS_PULLUP */
> >
> > > > > This doesn't work for me on Beaver. I need to turn the above line
> > > > > into
> > > > >
> > > > > this:
> > > > > nvidia,vbus-gpio = <&gpio 236 0>; /* PDD4 */
> > > > >
> > > > > PDD4 is the correct GPIO according to the schematics and the pin is
> > > > > high-active. Also as far as I can tell, 3 is not a meaningful value
> > > > > for the U-Boot GPIO bindings. Only the value 1 (low-active) is
> > > > > used.
> > > > >
> > > > > With that change applied on top of your patches I can see that a
> > > > > USB flash drive connected to USB3 is indeed powered. However I
> > > > > noticed
> > > > >
> > > > > something strange. When I try to use USB, I get this:
> > > > > Tegra30 (Beaver) # usb start
> > > > > (Re)start USB...
> > > > > USB0: set_host_mode: GPIO 236 high
> > > > > USB EHCI 1.00
> > > > > scanning bus 0 for devices... 1 USB Device(s) found
> > > > >
> > > > > scanning usb for storage devices... 0 Storage Device(s)
> > > > > found scanning usb for ethernet devices... 0 Ethernet
> > > > > Device(s) found
> > > > >
> > > > > So no storage device is detected, even though a USB flash drive is
> > > > > connected and powered properly. If I repeat the same command,
> > > > > however,
> > > > >
> > > > > the storage device is detected:
> > > > > Tegra30 (Beaver) # usb reset
> > > > > (Re)start USB...
> > > > > USB0: set_host_mode: GPIO 236 high
> > > > > USB EHCI 1.00
> > > > > scanning bus 0 for devices... 2 USB Device(s) found
> > > > >
> > > > > scanning usb for storage devices... 1 Storage Device(s)
> > > > > found scanning usb for ethernet devices... 0 Ethernet
> > > > > Device(s) found
> > > > >
> > > > > Any idea what might be going on here?
> > > >
> > > > Try waiting a little after setting the GPIO maybe? The drive might
> > > > need some time to settle.
> > >
> > > I can make it work on the first invocation of "usb start" by adding a
> > > rather long mdelay() at the very end of ehci_hcd_init() in the Tegra
> > > EHCI driver. The magic value seems to be 853 ms. 852 ms wasn't enough
> > > in any of the test runs. 853 ms always worked.
> > >
> > > However 850+ ms seems like a very long time for the device to settle,
> > > and keeping it in the driver probably isn't a good idea. Furthermore I
> > > cannot reproduce the same issue with a newer flash drive, which works
> > > fine with no additional delays.
> >
> > Try reverting 020bbcb "usb: hub: Power-cycle on root-hub ports" ...
> > there's a thread in the ML that it caused issues.
>
> I reverted the following two patches:
>
> 0bf796f usb: hub: Parallelize power-cycling of root-hub ports
> 020bbcb usb: hub: Power-cycle on root-hub ports
>
> because it wasn't trivial to revert only 020bbcb alone. However it
> didn't change anything regarding the problem I was seeing.
>
> Thierry
Ok, this looks ugly and calls for a bisect. Can you check it ? I'll try to test
if USB works for me on some EHCI-enabled device.
Best regards,
Marek Vasut
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
