Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
Set the board name appropriately for the board revision that
is detected.
Update the findfdt macro to load the a4 device tree binary.
Signed-off-by: Dan Murphy <dmur...@ti.com>
---
v2 - Fix checkpatch warnings - http://patchwork.ozlabs.org/patch/250854/
board/ti/panda/panda.c | 75 +++++++++++++++++++++++++++++++++++++---
include/configs/omap4_common.h | 2 +
2 files changed, 72 insertions(+), 5 deletions(-)
diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c
index 2bbe392..1a54be1 100644
--- a/board/ti/panda/panda.c
+++ b/board/ti/panda/panda.c
@@ -37,6 +37,11 @@
#endif
#define PANDA_ULPI_PHY_TYPE_GPIO 182
+#define PANDA_BOARD_ID_1_GPIO 101
+#define PANDA_ES_BOARD_ID_1_GPIO 48
+#define PANDA_BOARD_ID_2_GPIO 171
+#define PANDA_ES_BOARD_ID_3_GPIO 3
+#define PANDA_ES_BOARD_ID_4_GPIO 2
DECLARE_GLOBAL_DATA_PTR;
@@ -66,6 +71,70 @@ int board_eth_init(bd_t *bis)
return 0;
}
+/*
+* Routine: get_board_revision
+* Description: Detect if we are running on a panda revision A1-A6,
+* or an ES panda board. This can be done by reading
+* the level of GPIOs and checking the processor revisions.
+* This should result in:
+* Panda 4430:
+* GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
+* GPIO171, GPIO101, GPIO182: 1 0 1 => A6
+* Panda ES:
+* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
+* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
+*/
+int get_board_revision(void)
+{
+ int board_id0, board_id1, board_id2;
+ int board_id3, board_id4;
+ int board_id;
+
+ int processor_rev = omap_revision();
+
+ /* Setup the mux for the common board ID pins */
+ writew((IEN | M3), CONTROL_PADCONF_CORE + UNIPRO_TX0); /* gpio 171 */
+ writew((IEN | M3), CONTROL_PADCONF_CORE + FREF_CLK2_OUT); /* gpio 182 */
+
+ board_id0 = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
+ board_id2 = gpio_get_value(PANDA_BOARD_ID_2_GPIO);
+
+ if ((processor_rev >= OMAP4460_ES1_0 &&
+ processor_rev <= OMAP4460_ES1_1)) {
+ /* Setup the mux for the ES specific board ID pins */
+ /* gpio 101 */
+ writew((IEN | M3), CONTROL_PADCONF_CORE + GPMC_A24);
+ /* gpio 2 */
+ writew((IEN | M3), CONTROL_PADCONF_CORE + UNIPRO_RY0);
+ /* gpio 3 */
+ writew((IEN | M3), CONTROL_PADCONF_CORE + UNIPRO_RX1);
+
+ board_id1 = gpio_get_value(PANDA_ES_BOARD_ID_1_GPIO);
+ board_id3 = gpio_get_value(PANDA_ES_BOARD_ID_3_GPIO);
+ board_id4 = gpio_get_value(PANDA_ES_BOARD_ID_4_GPIO);
+
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es"));
+#endif
+ board_id = ((board_id4 << 4) | (board_id3 << 3) |
+ (board_id2 << 2) | (board_id1 << 1) | (board_id0));
+ } else {
+ /* Setup the mux for the Ax specific board ID pins */
+ /* gpio 101 */
+ writew((IEN | M3), CONTROL_PADCONF_CORE + FREF_CLK2_OUT);
+
+ board_id1 = gpio_get_value(PANDA_BOARD_ID_1_GPIO);
+ board_id = ((board_id2 << 2) | (board_id1 << 1) | (board_id0));
+
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ if ((board_id >= 0x3) && (processor_rev == OMAP4430_ES2_3))
+ setenv("board_name", strcat(CONFIG_SYS_BOARD, "-a4"));
+#endif
+ }
+
+ return board_id;
+}
+
/**
* @brief misc_init_r - Configure Panda board specific configurations
* such as power configurations, ethernet initialization as phase2 of
@@ -82,11 +151,7 @@ int misc_init_r(void)
if (omap_revision() == OMAP4430_ES1_0)
return 0;
-#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- if (omap_revision() >= OMAP4460_ES1_0 ||
- omap_revision() <= OMAP4460_ES1_1)
- setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es"));
-#endif
+ get_board_revision();
gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO);
phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO);
diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h
index d6448b0..cf41d9c 100644
--- a/include/configs/omap4_common.h
+++ b/include/configs/omap4_common.h
@@ -181,6 +181,8 @@
"setenv fdtfile omap4-sdp.dtb; fi; " \
"if test $board_name = panda; then " \
"setenv fdtfile omap4-panda.dtb; fi;" \
+ "if test $board_name = panda-a4; then " \
+ "setenv fdtfile omap4-panda-a4.dtb; fi;" \
"if test $board_name = panda-es; then " \
"setenv fdtfile omap4-panda-es.dtb; fi; \0" \
"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
--
1.7.5.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
