Dear Kuo-Jung Su,
> From: Kuo-Jung Su <dant...@faraday-tech.com>
>
> This patch add supports to both Faraday FUSBH200 and FOTG210,
> the differences between Faraday EHCI and standard EHCI as
> listed bellow:
>
> 1. The PORTSC starts at 0x30 instead of 0x44.
> 2. The CONFIGFLAG(0x40) is not only un-implemented, and
> also has its address removed.
> 3. Faraday EHCI is a TDI design, but it doesn't
> compatible with the general TDI implementation
> found at both U-Boot and Linux.
> 4. The ISOC descriptors differs from standard EHCI in
> several ways. Since U-boot doesn't support ISOC,
> we don't have to worry that.
>
> Signed-off-by: Kuo-Jung Su <dant...@faraday-tech.com>
> CC: Marek Vasut <ma...@denx.de>
> ---
> Changes for v4:
> - Use only macro constants and named bit/mask
> - Use weak-aliased functions for tdi implementation and
> also portsc registers to avoid poluting ehci.h with ifdefs
>
> Changes for v3:
> - Coding Style cleanup.
> - Drop bit fields from c struct.
> - Drop macros for wirtel()/readl(), call them directly.
> - Always insert a blank line between declarations and code.
> - Replace all the infinite wait loop with a timeout.
> - Add '__iomem' to all the declaration of HW register pointers.
>
> Changes for v2:
> - Coding Style cleanup.
> - Use readl(), writel(), clrsetbits_le32() to replace REG() macros.
> - Use structure based hardware registers to replace the macro constants.
> - Replace BIT() with BIT_MASK().
> - echi-faraday: Remove debug codes.
>
> common/usb_hub.c | 13 +-
> drivers/usb/host/Makefile | 1 +
> drivers/usb/host/ehci-faraday.c | 146 ++++++++++++++++
> drivers/usb/host/ehci-hcd.c | 104 ++++++++----
> include/usb/fotg210.h | 358
> +++++++++++++++++++++++++++++++++++++++ include/usb/fusbh200.h |
> 61 +++++++
> 6 files changed, 646 insertions(+), 37 deletions(-)
> create mode 100644 drivers/usb/host/ehci-faraday.c
> create mode 100644 include/usb/fotg210.h
> create mode 100644 include/usb/fusbh200.h
>
> diff --git a/common/usb_hub.c b/common/usb_hub.c
> index b5eeb62..3c6cb69 100644
Please split the EHCI changes from this patch.
> --- a/common/usb_hub.c
> +++ b/common/usb_hub.c
> @@ -419,6 +419,14 @@ static int usb_hub_configure(struct usb_device *dev)
> portstatus = le16_to_cpu(portsts->wPortStatus);
> portchange = le16_to_cpu(portsts->wPortChange);
>
> +#ifdef CONFIG_USB_EHCI_FARADAY
> + /* Faraday EHCI needs a long long delay here */
> + if (!portchange && !portstatus) {
> + if (get_timer(start) < 250)
> + continue;
> + }
> +#endif
I'd say just call a weak function here, in case some other non-EHCI compliant
controller happened to need this too. btw. does it need to be 250 ms or can you
poll for readiness somehow ?
> if ((portchange & USB_PORT_STAT_C_CONNECTION) ==
> (portstatus & USB_PORT_STAT_CONNECTION))
> break;
> @@ -441,7 +449,9 @@ static int usb_hub_configure(struct usb_device *dev)
> i + 1, portstatus);
> usb_clear_port_feature(dev, i + 1,
> USB_PORT_FEAT_C_ENABLE);
> -
> + /* The following hack causes a ghost device problem
> + * to Faraday EHCI */
Invalid multiline comment style (not that the one right below is a shining
example of a valid one :-( ).
/*
* This is how you
* do multiline comments.
*/
> +#ifndef CONFIG_USB_EHCI_FARADAY
> /* EM interference sometimes causes bad shielded USB
> * devices to be shutdown by the hub, this hack enables
> * them again. Works at least with mouse driver */
> @@ -453,6 +463,7 @@ static int usb_hub_configure(struct usb_device *dev)
> "re-enabling...\n", i + 1);
> usb_hub_port_connect_change(dev, i);
> }
> +#endif
> }
> if (portstatus & USB_PORT_STAT_SUSPEND) {
> USB_HUB_PRINTF("port %d suspend change\n", i + 1);
[...]
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
