Hi Naveen,
On Tue, Mar 12, 2013 at 3:58 AM, Naveen Krishna Chatradhi <
ch.nav...@samsung.com> wrote:
> Add support for hsi2c controller available on exynos5420.
>
> Note: driver currently supports only fast speed mode 100kbps
>
> Signed-off-by: Naveen Krishna Chatradhi <ch.nav...@samsung.com>
> Signed-off-by: R. Chandrasekar <rc.se...@samsung.com>
>
I just commented on the Linux driver, so some comments may apply here also.
> ---
> drivers/i2c/s3c24x0_i2c.c | 389
> ++++++++++++++++++++++++++++++++++++++++++---
> drivers/i2c/s3c24x0_i2c.h | 33 ++++
> 2 files changed, 397 insertions(+), 25 deletions(-)
>
> diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
> index 769a2ba..3117ab7 100644
> --- a/drivers/i2c/s3c24x0_i2c.c
> +++ b/drivers/i2c/s3c24x0_i2c.c
> @@ -32,6 +32,7 @@
> #include <asm/arch/clk.h>
> #include <asm/arch/cpu.h>
> #include <asm/arch/pinmux.h>
> +#include <asm/arch/clock.h>
> #else
> #include <asm/arch/s3c24x0_cpu.h>
> #endif
> @@ -50,6 +51,60 @@
> #define I2C_NOK_LA 3 /* Lost arbitration */
> #define I2C_NOK_TOUT 4 /* time out */
>
> +/* HSI2C specific register description */
> +
> +/* I2C_CTL Register bits */
> +#define HSI2C_FUNC_MODE_I2C (1u << 0)
> +#define HSI2C_MASTER (1u << 3)
> +#define HSI2C_RXCHON (1u << 6) /* Write/Send */
> +#define HSI2C_TXCHON (1u << 7) /* Read/Receive */
> +#define HSI2C_SW_RST (1u << 31)
> +
> +/* I2C_FIFO_CTL Register bits */
> +#define HSI2C_RXFIFO_EN (1u << 0)
> +#define HSI2C_TXFIFO_EN (1u << 1)
> +#define HSI2C_TXFIFO_TRIGGER_LEVEL (0x20 << 16)
> +#define HSI2C_RXFIFO_TRIGGER_LEVEL (0x20 << 4)
> +
> +/* I2C_TRAILING_CTL Register bits */
> +#define HSI2C_TRAILING_COUNT (0xff)
> +
> +/* I2C_INT_EN Register bits */
> +#define HSI2C_INT_TX_ALMOSTEMPTY_EN (1u << 0)
> +#define HSI2C_INT_RX_ALMOSTFULL_EN (1u << 1)
> +#define HSI2C_INT_TRAILING_EN (1u << 6)
> +#define HSI2C_INT_I2C_EN (1u << 9)
> +
> +/* I2C_CONF Register bits */
> +#define HSI2C_AUTO_MODE (1u << 31)
> +#define HSI2C_10BIT_ADDR_MODE (1u << 30)
> +#define HSI2C_HS_MODE (1u << 29)
> +
> +/* I2C_AUTO_CONF Register bits */
> +#define HSI2C_READ_WRITE (1u << 16)
> +#define HSI2C_STOP_AFTER_TRANS (1u << 17)
> +#define HSI2C_MASTER_RUN (1u << 31)
> +
> +/* I2C_TIMEOUT Register bits */
> +#define HSI2C_TIMEOUT_EN (1u << 31)
> +
> +/* I2C_TRANS_STATUS register bits */
> +#define HSI2C_MASTER_BUSY (1u << 17)
> +#define HSI2C_SLAVE_BUSY (1u << 16)
> +#define HSI2C_NO_DEV (1u << 3)
> +#define HSI2C_NO_DEV_ACK (1u << 2)
> +#define HSI2C_TRANS_ABORT (1u << 1)
> +#define HSI2C_TRANS_DONE (1u << 0)
> +#define HSI2C_TIMEOUT_AUTO (0u << 0)
> +
> +#define HSI2C_SLV_ADDR_MAS(x) ((x & 0x3ff) << 10)
> +
> +/* Controller operating frequency, timing values for operation
> + * are calculated against this frequency
> + */
> +#define HSI2C_FS_TX_CLOCK 1000000
> +
> +/* S3C I2C Controller bits */
> #define I2CSTAT_BSY 0x20 /* Busy bit */
> #define I2CSTAT_NACK 0x01 /* Nack bit */
> #define I2CCON_ACKGEN 0x80 /* Acknowledge generation */
> @@ -61,6 +116,7 @@
>
> #define I2C_TIMEOUT 1 /* 1 second */
>
> +#define HSI2C_TIMEOUT 100
>
> /*
> * For SPL boot some boards need i2c before SDRAM is initialised so force
> @@ -120,9 +176,23 @@ static int WaitForXfer(struct s3c24x0_i2c *i2c)
> return (readl(&i2c->iiccon) & I2CCON_IRPND) ? I2C_OK :
> I2C_NOK_TOUT;
> }
>
> -static int IsACK(struct s3c24x0_i2c *i2c)
> +static int hsi2c_wait_for_irq(struct exynos5_hsi2c *i2c)
> {
> - return !(readl(&i2c->iicstat) & I2CSTAT_NACK);
> + int i = HSI2C_TIMEOUT * 10;
> + int ret = I2C_NOK_TOUT;
> +
> + while (i > 0) {
> + /* wait for a while and retry */
> + udelay(50);
> + if (readl(&i2c->usi_int_stat) &
> + (HSI2C_INT_I2C_EN | HSI2C_INT_TX_ALMOSTEMPTY_EN)) {
> + ret = I2C_OK;
> + break;
> + }
> + i--;
>
Please can we use the get_timer() method for timeouts instead of udelay()?
> + }
> +
> + return ret;
> }
>
> static void ReadWriteByte(struct s3c24x0_i2c *i2c)
> @@ -130,6 +200,22 @@ static void ReadWriteByte(struct s3c24x0_i2c *i2c)
> writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon);
> }
>
> +static void hsi2c_clear_irqpd(struct exynos5_hsi2c *i2c)
> +{
> + writel(readl(&i2c->usi_int_stat), &i2c->usi_int_stat);
> +}
> +
> +static int hsi2c_isack(struct exynos5_hsi2c *i2c)
> +{
> + return readl(&i2c->usi_trans_status) &
> + (HSI2C_NO_DEV | HSI2C_NO_DEV_ACK);
> +}
> +
> +static int IsACK(struct s3c24x0_i2c *i2c)
>
There are two functions - hsi2c_isack() and IsAck(). What is the difference?
> +{
> + return !(readl(&i2c->iicstat) & I2CSTAT_NACK);
> +}
> +
> static struct s3c24x0_i2c *get_base_i2c(void)
> {
> #ifdef CONFIG_EXYNOS4
> @@ -147,6 +233,18 @@ static struct s3c24x0_i2c *get_base_i2c(void)
> #endif
> }
>
> +static struct exynos5_hsi2c *get_base_hsi2c(void)
> +{
> + struct exynos5_hsi2c *i2c = NULL;
> + int bus = g_current_bus;
> +
> + if (proid_is_exynos5420())
> + i2c = (struct exynos5_hsi2c *)(EXYNOS5420_I2C_BASE +
> + ((bus) * EXYNOS5_I2C_SPACING));
> +
> + return i2c;
> +}
>
This should come from the device tree information that you are decoding
(the ->reg property).
> +
> static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd)
> {
> ulong freq, pres = 16, div;
> @@ -174,6 +272,74 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c, int
> speed, int slaveadd)
> writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat);
> }
>
> +static void hsi2c_ch_init(struct exynos5_hsi2c *i2c, int speed)
> +{
> + u32 i2c_timeout;
> + ulong clkin = get_i2c_clk();
> + u32 i2c_timing_s1;
> + u32 i2c_timing_s2;
> + u32 i2c_timing_s3;
> + u32 i2c_timing_sla;
> + unsigned int op_clk = HSI2C_FS_TX_CLOCK;
> + unsigned int n_clkdiv;
> + unsigned int t_start_su, t_start_hd;
> + unsigned int t_stop_su;
> + unsigned int t_data_su, t_data_hd;
> + unsigned int t_scl_l, t_scl_h;
> + unsigned int t_sr_release;
> + unsigned int t_ftl_cycle;
> + unsigned int i = 0, utemp0 = 0, utemp1 = 0, utemp2 = 0;
> +
> + /* FPCLK / FI2C =
> + * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
> + * uTemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2)
> + * uTemp1 = (TSCLK_L + TSCLK_H + 2)
> + * uTemp2 = TSCLK_L + TSCLK_H
> + */
> + t_ftl_cycle = (readl(&i2c->usi_conf) >> 16) & 0x7;
> + utemp0 = (clkin / op_clk) - 8 - 2 * t_ftl_cycle;
> +
> + /* CLK_DIV max is 256 */
> + for (i = 0; i < 256; i++) {
> + utemp1 = utemp0 / (i + 1);
> + /* SCLK_L/H max is 256 / 2 */
> + if (utemp1 < 128) {
> + utemp2 = utemp1 - 2;
> + break;
> + }
> + }
> +
> + n_clkdiv = i;
> + t_scl_l = utemp2 / 2;
> + t_scl_h = utemp2 / 2;
> + t_start_su = t_scl_l;
> + t_start_hd = t_scl_l;
> + t_stop_su = t_scl_l;
> + t_data_su = t_scl_l / 2;
> + t_data_hd = t_scl_l / 2;
> + t_sr_release = utemp2;
> +
> + i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su <<
> 8;
> + i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0;
> + i2c_timing_s3 = n_clkdiv << 16 | t_sr_release << 0;
> + i2c_timing_sla = t_data_hd << 0;
> +
> + writel(HSI2C_TRAILING_COUNT, &i2c->usi_trailing_ctl);
> +
> + /* Clear to enable Timeout */
> + i2c_timeout = readl(&i2c->usi_timeout);
> + i2c_timeout &= ~HSI2C_TIMEOUT_EN;
> + writel(i2c_timeout, &i2c->usi_timeout);
> +
> + writel(readl(&i2c->usi_conf) | HSI2C_AUTO_MODE, &i2c->usi_conf);
> +
> + /* Currently operating in Fast speed mode. */
> + writel(i2c_timing_s1, &i2c->usi_timing_fs1);
> + writel(i2c_timing_s2, &i2c->usi_timing_fs2);
> + writel(i2c_timing_s3, &i2c->usi_timing_fs3);
> + writel(i2c_timing_sla, &i2c->usi_timing_sla);
> +}
> +
> /*
> * MULTI BUS I2C support
> */
> @@ -181,16 +347,18 @@ static void i2c_ch_init(struct s3c24x0_i2c *i2c, int
> speed, int slaveadd)
> #ifdef CONFIG_I2C_MULTI_BUS
> int i2c_set_bus_num(unsigned int bus)
> {
> - struct s3c24x0_i2c *i2c;
> -
> if ((bus < 0) || (bus >= CONFIG_MAX_I2C_NUM)) {
> debug("Bad bus: %d\n", bus);
> return -1;
> }
>
> g_current_bus = bus;
> - i2c = get_base_i2c();
> - i2c_ch_init(i2c, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> + if (proid_is_exynos5420() && (bus > 3)) {
> + hsi2c_ch_init(get_base_hsi2c(),
> + CONFIG_SYS_I2C_SPEED);
> + } else
> + i2c_ch_init(get_base_i2c(), CONFIG_SYS_I2C_SPEED,
> + CONFIG_SYS_I2C_SLAVE);
>
> return 0;
> }
> @@ -269,24 +437,182 @@ void i2c_init(int speed, int slaveadd)
> }
>
> /*
> + * Send a STOP event and wait for it to have completed
> + *
> + * @param mode If it is a master transmitter or receiver
> + * @return I2C_OK if the line became idle before timeout I2C_NOK_TOUT
> otherwise
> + */
> +static int hsi2c_send_stop(struct exynos5_hsi2c *i2c, int result)
> +{
> + int timeout;
> + int ret = I2C_NOK_TOUT;
> +
> + /* Wait for the STOP to send and the bus to go idle */
> + for (timeout = HSI2C_TIMEOUT; timeout > 0; timeout -= 5) {
> + if (!(readl(&i2c->usi_trans_status) & HSI2C_MASTER_BUSY)) {
> + ret = I2C_OK;
> + goto out;
> + }
> + udelay(5);
> + }
> + out:
> + /* Setting the STOP event to fire */
> + writel(HSI2C_FUNC_MODE_I2C, &i2c->usi_ctl);
> + writel(0x0, &i2c->usi_int_en);
> +
> + return (result == I2C_OK) ? ret : result;
> +}
> +
> +static int hsi2c_write(unsigned char chip,
> + unsigned char addr[],
> + unsigned char alen,
> + unsigned char data[],
> + unsigned short len)
> +{
> + struct exynos5_hsi2c *i2c = get_base_hsi2c();
> + int i = 0, result = I2C_OK;
> + u32 i2c_auto_conf;
> + u32 stat;
> +
> + /* Check I2C bus idle */
> + i = HSI2C_TIMEOUT * 20;
> + while ((readl(&i2c->usi_trans_status) & HSI2C_MASTER_BUSY)
> + && (i > 0)) {
> + udelay(50);
> + i--;
> + }
>
It seems like perhaps you should have a function to wait until not busy and
call it from the above function, and here.
> +
> + stat = readl(&i2c->usi_trans_status);
> +
> + if (stat & HSI2C_MASTER_BUSY) {
> + debug("%s: bus busy\n", __func__);
> + return I2C_NOK_TOUT;
> + }
> + /* Disable TXFIFO and RXFIFO */
> + writel(0, &i2c->usi_fifo_ctl);
> +
> + /* chip address */
> + writel(HSI2C_SLV_ADDR_MAS(chip), &i2c->i2c_addr);
> +
> + /* Enable interrupts */
> + writel((HSI2C_INT_I2C_EN | HSI2C_INT_TX_ALMOSTEMPTY_EN),
> + &i2c->usi_int_en);
> +
> + /* usi_ctl enable i2c func, master write configure */
> + writel((HSI2C_TXCHON | HSI2C_FUNC_MODE_I2C | HSI2C_MASTER),
> + &i2c->usi_ctl);
> +
> + /* i2c_conf configure */
> + writel(readl(&i2c->usi_conf) | HSI2C_AUTO_MODE, &i2c->usi_conf);
> +
> + /* auto_conf for write length and stop configure */
> + i2c_auto_conf = ((len + alen) | HSI2C_STOP_AFTER_TRANS);
> + i2c_auto_conf &= ~HSI2C_READ_WRITE;
> + writel(i2c_auto_conf, &i2c->usi_auto_conf);
> +
> + /* Master run, start xfer */
> + writel(readl(&i2c->usi_auto_conf) | HSI2C_MASTER_RUN,
> + &i2c->usi_auto_conf);
> +
> + result = hsi2c_wait_for_irq(i2c);
> + if ((result == I2C_OK) && hsi2c_isack(i2c)) {
> + result = I2C_NACK;
> + goto err;
> + }
> +
> + for (i = 0; i < alen && (result == I2C_OK); i++) {
> + writel(addr[i], &i2c->usi_txdata);
> + result = hsi2c_wait_for_irq(i2c);
> + }
> +
> + for (i = 0; i < len && (result == I2C_OK); i++) {
> + writel(data[i], &i2c->usi_txdata);
> + result = hsi2c_wait_for_irq(i2c);
>
Do we have to wait for an irq after every tx byte?
> + }
> +
> + err:
> + hsi2c_clear_irqpd(i2c);
> + return hsi2c_send_stop(i2c, result);
> +}
> +
> +static int hsi2c_read(unsigned char chip,
> + unsigned char addr[],
> + unsigned char alen,
> + unsigned char data[],
> + unsigned short len,
> + int check)
>
This seems to have a lot of common code with the above. Should they be
joined up?
> +{
> + struct exynos5_hsi2c *i2c = get_base_hsi2c();
> + int i, result;
> + u32 i2c_auto_conf;
> +
> + if (!check) {
> + result = hsi2c_write(chip, addr, alen, data, 0);
> + if (result != I2C_OK) {
> + debug("write failed Result = %d\n", result);
> + return result;
> + }
> + }
> +
> + /* start read */
> + /* Disable TXFIFO and RXFIFO */
> + writel(0, &i2c->usi_fifo_ctl);
> +
> + /* chip address */
> + writel(HSI2C_SLV_ADDR_MAS(chip), &i2c->i2c_addr);
> +
> + /* Enable interrupts */
> + writel(HSI2C_INT_I2C_EN, &i2c->usi_int_en);
> +
> + /* i2c_conf configure */
>
outdent
> + writel(readl(&i2c->usi_conf) | HSI2C_AUTO_MODE, &i2c->usi_conf);
> +
> + /* auto_conf, length and stop configure */
> + i2c_auto_conf = (len | HSI2C_STOP_AFTER_TRANS | HSI2C_READ_WRITE);
> + writel(i2c_auto_conf, &i2c->usi_auto_conf);
> +
> + /* usi_ctl enable i2c func, master WRITE configure */
> + writel((HSI2C_RXCHON | HSI2C_FUNC_MODE_I2C | HSI2C_MASTER),
> + &i2c->usi_ctl);
> +
> + /* Master run, start xfer */
> + writel(readl(&i2c->usi_auto_conf) | HSI2C_MASTER_RUN,
> + &i2c->usi_auto_conf);
> +
> + result = hsi2c_wait_for_irq(i2c);
> + if ((result == I2C_OK) && hsi2c_isack(i2c)) {
> + result = I2C_NACK;
> + goto err;
> + }
> +
> + for (i = 0; i < len && (result == I2C_OK); i++) {
> + result = hsi2c_wait_for_irq(i2c);
> + data[i] = readl(&i2c->usi_rxdata);
> + }
>
I suppose the FIFOs are not used here. How larger are the FIFOs?
> + err:
> + /* Stop and quit */
> + hsi2c_clear_irqpd(i2c);
> + return hsi2c_send_stop(i2c, result);
> +}
> +
> +/*
> * cmd_type is 0 for write, 1 for read.
> *
> * addr_len can take any value from 0-255, it is only limited
> * by the char, we could make it larger if needed. If it is
> * 0 we skip the address write cycle.
> */
> -static int i2c_transfer(struct s3c24x0_i2c *i2c,
> - unsigned char cmd_type,
> +static int i2c_transfer(unsigned char cmd_type,
> unsigned char chip,
> unsigned char addr[],
> unsigned char addr_len,
> unsigned char data[],
> unsigned short data_len)
> {
> + struct s3c24x0_i2c *i2c = get_base_i2c();
> int i, result;
>
> if (data == 0 || data_len == 0) {
> - /*Don't support data transfer of no length or to address 0
> */
> debug("i2c_transfer: bad call\n");
> return I2C_NOK;
> }
> @@ -428,10 +754,8 @@ static int i2c_transfer(struct s3c24x0_i2c *i2c,
>
> int i2c_probe(uchar chip)
> {
> - struct s3c24x0_i2c *i2c;
> uchar buf[1];
>
> - i2c = get_base_i2c();
> buf[0] = 0;
>
> /*
> @@ -439,12 +763,15 @@ int i2c_probe(uchar chip)
> * address was <ACK>ed (i.e. there was a chip at that address which
> * drove the data line low).
> */
> - return i2c_transfer(i2c, I2C_READ, chip << 1, 0, 0, buf, 1) !=
> I2C_OK;
> + if (proid_is_exynos5420() && (g_current_bus > 3))
> + return (hsi2c_read(chip, 0, 1, buf, 1, 1) != I2C_OK);
>
I think the type of i2c port should be set by the FDT, not hard-coded
according to the chip type.
> + else
> + return i2c_transfer(
> + I2C_READ, chip << 1, 0, 0, buf, 1) !=
> I2C_OK;
> }
>
> int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
> {
> - struct s3c24x0_i2c *i2c;
> uchar xaddr[4];
> int ret;
>
> @@ -476,9 +803,13 @@ int i2c_read(uchar chip, uint addr, int alen, uchar
> *buffer, int len)
> chip |= ((addr >> (alen * 8)) &
> CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> #endif
> - i2c = get_base_i2c();
> - ret = i2c_transfer(i2c, I2C_READ, chip << 1, &xaddr[4 - alen],
> alen,
> - buffer, len);
> + if (proid_is_exynos5420() && (g_current_bus > 3))
> + ret = hsi2c_read(chip, &xaddr[4 - alen],
> + alen, buffer, len, 0);
+ else
> + ret = i2c_transfer(I2C_READ, chip << 1,
> + &xaddr[4 - alen], alen, buffer, len);
> +
> if (ret != 0) {
> debug("I2c read: failed %d\n", ret);
> return 1;
> @@ -488,7 +819,6 @@ int i2c_read(uchar chip, uint addr, int alen, uchar
> *buffer, int len)
>
> int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
> {
> - struct s3c24x0_i2c *i2c;
> uchar xaddr[4];
>
> if (alen > 4) {
> @@ -518,31 +848,36 @@ int i2c_write(uchar chip, uint addr, int alen, uchar
> *buffer, int len)
> chip |= ((addr >> (alen * 8)) &
> CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
> #endif
> - i2c = get_base_i2c();
> - return (i2c_transfer
> - (i2c, I2C_WRITE, chip << 1, &xaddr[4 - alen], alen, buffer,
> - len) != 0);
> + if (proid_is_exynos5420() && (g_current_bus > 3))
> + return (hsi2c_write(chip, &xaddr[4 - alen],
> + alen, buffer, len) != 0);
> + else
> + return (i2c_transfer(I2C_WRITE, chip << 1,
> + &xaddr[4 - alen], alen, buffer, len) != 0);
> }
>
> #ifdef CONFIG_OF_CONTROL
> void board_i2c_init(const void *blob)
> {
> + struct s3c24x0_i2c_bus *bus;
> int node_list[CONFIG_MAX_I2C_NUM];
> int count, i;
>
> count = fdtdec_find_aliases_for_id(blob, "i2c",
> COMPAT_SAMSUNG_S3C2440_I2C, node_list,
> CONFIG_MAX_I2C_NUM);
> -
> for (i = 0; i < count; i++) {
> - struct s3c24x0_i2c_bus *bus;
> int node = node_list[i];
>
> if (node <= 0)
> continue;
> bus = &i2c_bus[i];
> +
> bus->regs = (struct s3c24x0_i2c *)
> - fdtdec_get_addr(blob, node, "reg");
> + fdtdec_get_addr(blob, node, "reg");
>
Here you have bus->regs so you should use it in the driver.
> + bus->hsregs = (struct exynos5_hsi2c *)
> + fdtdec_get_addr(blob, node, "reg");
> +
>
All of the ports here will be COMPAT_SAMSUNG_S3C2440_I2C. I think you need
to find ports of a different type for the high speed i2c. Perhaps look at
how tegra i2c handles having two different node types in the same driver.
The type of a port needs to be stored in the bus structure, and I think
this should be done even in the non-FDT case, to simplify the code.
> bus->id = pinmux_decode_periph_id(blob, node);
> bus->node = node;
> bus->bus_num = i2c_busses++;
> @@ -589,7 +924,11 @@ int i2c_reset_port_fdt(const void *blob, int node)
> return -1;
> }
>
> - i2c_ch_init(i2c->regs, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
> + if (proid_is_exynos5420() && (bus > 3))
> + hsi2c_ch_init(i2c->hsregs, CONFIG_SYS_I2C_SPEED);
> + else
> + i2c_ch_init(i2c->regs, CONFIG_SYS_I2C_SPEED,
> + CONFIG_SYS_I2C_SLAVE);
>
> return 0;
> }
> diff --git a/drivers/i2c/s3c24x0_i2c.h b/drivers/i2c/s3c24x0_i2c.h
> index a56d749..81ed19c 100644
> --- a/drivers/i2c/s3c24x0_i2c.h
> +++ b/drivers/i2c/s3c24x0_i2c.h
> @@ -31,10 +31,43 @@ struct s3c24x0_i2c {
> u32 iiclc;
> };
>
> +struct exynos5_hsi2c {
> + u32 usi_ctl;
> + u32 usi_fifo_ctl;
> + u32 usi_trailing_ctl;
> + u32 usi_clk_ctl;
> + u32 usi_clk_slot;
> + u32 spi_ctl;
> + u32 uart_ctl;
> + u32 res1;
> + u32 usi_int_en;
> + u32 usi_int_stat;
> + u32 usi_modem_stat;
> + u32 usi_error_stat;
> + u32 usi_fifo_stat;
> + u32 usi_txdata;
> + u32 usi_rxdata;
> + u32 res2;
> + u32 usi_conf;
> + u32 usi_auto_conf;
> + u32 usi_timeout;
> + u32 usi_manual_cmd;
> + u32 usi_trans_status;
> + u32 usi_timing_hs1;
> + u32 usi_timing_hs2;
> + u32 usi_timing_hs3;
> + u32 usi_timing_fs1;
> + u32 usi_timing_fs2;
> + u32 usi_timing_fs3;
> + u32 usi_timing_sla;
> + u32 i2c_addr;
> +};
> +
> struct s3c24x0_i2c_bus {
> int node; /* device tree node */
> int bus_num; /* i2c bus number */
> struct s3c24x0_i2c *regs;
> + struct exynos5_hsi2c *hsregs;
> int id;
> };
> #endif /* _S3C24X0_I2C_H */
> --
> 1.7.9.5
>
> Regards,
Simon
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
