Dear Otavio Salvador,
> The i.MX23 just one USB port so disable the second controller probe
> when building for i.MX23.
>
> Signed-off-by: Otavio Salvador <ota...@ossystems.com.br>
> ---
> Changes in v2:
> - Avoid wrong clock setting in MX23
>
> drivers/usb/host/ehci-mxs.c | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/drivers/usb/host/ehci-mxs.c b/drivers/usb/host/ehci-mxs.c
> index 5062af5..b7bf856 100644
> --- a/drivers/usb/host/ehci-mxs.c
> +++ b/drivers/usb/host/ehci-mxs.c
> @@ -50,10 +50,12 @@ int mxs_ehci_get_port(struct ehci_mxs *mxs_usb, int
> port) usb_base = MXS_USBCTRL0_BASE;
> phy_base = MXS_USBPHY0_BASE;
> break;
> +#ifdef CONFIG_MX28
> case 1:
> usb_base = MXS_USBCTRL1_BASE;
> phy_base = MXS_USBPHY1_BASE;
> break;
> +#endif
> default:
> printf("CONFIG_EHCI_MXS_PORT (port = %d)\n", port);
> return -1;
> @@ -67,7 +69,9 @@ int mxs_ehci_get_port(struct ehci_mxs *mxs_usb, int port)
> /* This DIGCTL register ungates clock to USB */
> #define HW_DIGCTL_CTRL 0x8001c000
> #define HW_DIGCTL_CTRL_USB0_CLKGATE (1 << 2)
> +#ifdef CONFIG_MX28
> #define HW_DIGCTL_CTRL_USB1_CLKGATE (1 << 16)
> +#endif
>
> int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor
> **hcor) {
> @@ -95,8 +99,12 @@ int ehci_hcd_init(int index, struct ehci_hccr **hccr,
> struct ehci_hcor **hcor) writel(CLKCTRL_PLL1CTRL0_EN_USB_CLKS |
> CLKCTRL_PLL1CTRL0_POWER,
> &clkctrl_regs->hw_clkctrl_pll1ctrl0_set);
>
> +#if defined(CONFIG_MX23)
> + writel(HW_DIGCTL_CTRL_USB0_CLKGATE, &digctl_ctrl->reg_clr);
What is that large space before '&digctl_regs->...' ?
> +#elif defined(CONFIG_MX28)
> writel(HW_DIGCTL_CTRL_USB0_CLKGATE | HW_DIGCTL_CTRL_USB1_CLKGATE,
> &digctl_ctrl->reg_clr);
> +#endif
I'm sure these can be wrapped in much more elegant way, yes?
>
> /* Start USB PHY */
> writel(0, &ehci_mxs.phy_regs->hw_usbphy_pwd);
> @@ -153,8 +161,12 @@ int ehci_hcd_stop(int index)
> &clkctrl_regs->hw_clkctrl_pll1ctrl0_clr);
>
> /* Gate off the USB clock */
> +#if defined(CONFIG_MX23)
> + writel(HW_DIGCTL_CTRL_USB0_CLKGATE, &digctl_ctrl->reg_set);
> +#elif defined(CONFIG_MX28)
> writel(HW_DIGCTL_CTRL_USB0_CLKGATE | HW_DIGCTL_CTRL_USB1_CLKGATE,
> &digctl_ctrl->reg_set);
> +#endif
>
> return 0;
> }
Best regards,
Marek Vasut
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
