Hi Amar,
On Fri, Jan 4, 2013 at 1:34 AM, Amar <amarendra...@samsung.com> wrote:
> This patch adds support for EMMC booting on SMDK5250.
>
> Changes from V1:
> 1)Updated spl_boot.c file to maintain irom pointer table
> instead of using the #define values defined in header file.
>
> Changes from V2:
> 1)Updation of commit message and resubmition of proper patch set.
>
> Changes from V3:
> No change.
>
> Signed-off-by: Amar <amarendra...@samsung.com>
> ---
> board/samsung/smdk5250/clock_init.c | 15 +++++++++++
> board/samsung/smdk5250/clock_init.h | 5 ++++
> board/samsung/smdk5250/spl_boot.c | 52
> ++++++++++++++++++++++++++++++++-----
> 3 files changed, 65 insertions(+), 7 deletions(-)
>
> diff --git a/board/samsung/smdk5250/clock_init.c
> b/board/samsung/smdk5250/clock_init.c
> index c009ae5..154993c 100644
> --- a/board/samsung/smdk5250/clock_init.c
> +++ b/board/samsung/smdk5250/clock_init.c
> @@ -28,6 +28,7 @@
> #include <asm/arch/clk.h>
> #include <asm/arch/clock.h>
> #include <asm/arch/spl.h>
> +#include <asm/arch/dwmmc.h>
>
> #include "clock_init.h"
> #include "setup.h"
> @@ -664,3 +665,17 @@ void clock_init_dp_clock(void)
> /* We run DP at 267 Mhz */
> setbits_le32(&clk->div_disp1_0, CLK_DIV_DISP1_0_FIMD1);
> }
> +
> +/*
> + * Set clock divisor value for booting from EMMC.
> + * Set DWMMC channel-0 clk div to operate mmc0 device at 50MHz.
> + */
> +void emmc_boot_clk_div_set(void)
> +{
> + struct exynos5_clock *clk = (struct exynos5_clock
> *)EXYNOS5_CLOCK_BASE;
> + unsigned int div_mmc;
> +
> + div_mmc = readl((unsigned int) &clk->div_fsys1) &
> ~FSYS1_MMC0_DIV_MASK;
> + div_mmc |= FSYS1_MMC0_DIV_VAL;
> + writel(div_mmc, (unsigned int) &clk->div_fsys1);
> +}
> diff --git a/board/samsung/smdk5250/clock_init.h
> b/board/samsung/smdk5250/clock_init.h
> index f751bcb..20a1d47 100644
> --- a/board/samsung/smdk5250/clock_init.h
> +++ b/board/samsung/smdk5250/clock_init.h
> @@ -146,4 +146,9 @@ struct mem_timings *clock_get_mem_timings(void);
> * Initialize clock for the device
> */
> void system_clock_init(void);
> +
> +/*
> + * Set clock divisor value for booting from EMMC.
> + */
> +void emmc_boot_clk_div_set(void);
> #endif
> diff --git a/board/samsung/smdk5250/spl_boot.c
> b/board/samsung/smdk5250/spl_boot.c
> index d8f3c1e..906e197 100644
> --- a/board/samsung/smdk5250/spl_boot.c
> +++ b/board/samsung/smdk5250/spl_boot.c
> @@ -23,16 +23,38 @@
> #include<common.h>
> #include<config.h>
>
> +#include <asm/arch-exynos/dmc.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/clk.h>
> +
> +#include "clock_init.h"
> +
> +/* Index into irom ptr table */
> +enum index {
> + MMC_INDEX,
> + EMMC44_INDEX,
> + EMMC44_END_INDEX,
> + SPI_INDEX,
> +};
> +
> +/* IROM Function Pointers Table */
> +u32 irom_ptr_table[] = {
> + [MMC_INDEX] = 0x02020030, /* iROM Function Pointer-SDMMC boot */
> + [EMMC44_INDEX] = 0x02020044, /* iROM Function Pointer-EMMC4.4
> boot*/
> + [EMMC44_END_INDEX] = 0x02020048,/* iROM Function Pointer
> + -EMMC4.4 end boot operation */
> + [SPI_INDEX] = 0x02020058, /* iROM Function Pointer-SPI boot */
> + };
> +
> enum boot_mode {
> BOOT_MODE_MMC = 4,
> BOOT_MODE_SERIAL = 20,
> + BOOT_MODE_EMMC = 8, /* EMMC4.4 */
> /* Boot based on Operating Mode pin settings */
> BOOT_MODE_OM = 32,
> BOOT_MODE_USB, /* Boot using USB download */
> };
>
> - typedef u32 (*spi_copy_func_t)(u32 offset, u32 nblock, u32 dst);
> -
> /*
> * Copy U-boot from mmc to RAM:
> * COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
> @@ -40,23 +62,39 @@ enum boot_mode {
> */
> void copy_uboot_to_ram(void)
> {
> - spi_copy_func_t spi_copy;
> enum boot_mode bootmode;
> - u32 (*copy_bl2)(u32, u32, u32);
> -
> + u32 (*spi_copy)(u32 offset, u32 nblock, u32 dst);
> + u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst);
> + u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst);
> + void (*end_bootop_from_emmc)(void);
> + /* read Operation Mode ststus register to find the bootmode */
> bootmode = readl(EXYNOS5_POWER_BASE) & OM_STAT;
>
> switch (bootmode) {
> case BOOT_MODE_SERIAL:
> - spi_copy = *(spi_copy_func_t *)EXYNOS_COPY_SPI_FNPTR_ADDR;
> + spi_copy = (void *) *(u32 *)irom_ptr_table[SPI_INDEX];
This looks OK to me. My only suggestion is to put the lookup in a function like:
static void *get_irom_func(int index)
and avoid all the casting here.
> spi_copy(SPI_FLASH_UBOOT_POS, CONFIG_BL2_SIZE,
> CONFIG_SYS_TEXT_BASE);
> break;
Re SPI, the IROM performance is quite slow - do you plan to send up
the U-Boot SPI code version? with a 32KB SPL there might be room to
just use the normal driver.
> case BOOT_MODE_MMC:
> - copy_bl2 = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR;
> + copy_bl2 = (void *) *(u32 *)irom_ptr_table[MMC_INDEX];
> copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT,
> CONFIG_SYS_TEXT_BASE);
> break;
> + case BOOT_MODE_EMMC:
> + /* Set the FSYS1 clock divisor value for EMMC boot */
> + emmc_boot_clk_div_set();
> +
> + copy_bl2_from_emmc =
> + (void *) *(u32 *)irom_ptr_table[EMMC44_INDEX];
> + end_bootop_from_emmc =
> + (void *) *(u32 *)irom_ptr_table[EMMC44_END_INDEX];
> +
> + copy_bl2_from_emmc(BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
> + end_bootop_from_emmc();
> +
> + break;
> +
> default:
> break;
> }
> --
> 1.8.0
>
Regards,
Simon
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
