Ping. Please consider making this into the upcoming release. Jean-Christophe PLAGNIOL-VILLARD wrote: > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[EMAIL PROTECTED]> > > diff --git a/README.imx31 b/README.imx31 > deleted file mode 100644 > index f545f01..0000000 > --- a/README.imx31 > +++ /dev/null > @@ -1,13 +0,0 @@ > -i.MX31 specific Configuration Options: > --------------------------------------- > - > -- Timer precision: > - CONFIG_MX31_TIMER_HIGH_PRECISION > - > - Enable higher precision timer. The low-precision timer > - (default) provides approximately 4% error, whereas the > - high-precision timer is about 0.4% accurate. The extra > - accuracy is achieved at the cost of higher computational > - overhead, which, in places where time is measured, should > - not be critical, so, it should be safe to enable this > - option. > diff --git a/doc/README.imx31 b/doc/README.imx31 > new file mode 100644 > index 0000000..91ef766 > --- /dev/null > +++ b/doc/README.imx31 > @@ -0,0 +1,29 @@ > +U-Boot for Freescale i.MX31 > + > +This file contains information for the port of U-Boot to the Freescale > +i.MX31 SoC. > + > +1. CONFIGURATION OPTIONS/SETTINGS > +--------------------------------- > + > +1.1 Configuration of MC13783 SPI bus > +------------------------------------ > + The power management companion chip MC13783 is connected to the > + i.MX31 via an SPI bus. Use the following configuration options > + to setup the bus and chip select used for a particular board. > + > + CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected > to. > + Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3. > + CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s > connected to. > + > +1.2 Timer precision > +------------------- > + CONFIG_MX31_TIMER_HIGH_PRECISION > + > + Enable higher precision timer. The low-precision timer > + (default) provides approximately 4% error, whereas the > + high-precision timer is about 0.4% accurate. The extra > + accuracy is achieved at the cost of higher computational > + overhead, which, in places where time is measured, should > + not be critical, so, it should be safe to enable this > + option. > diff --git a/doc/README.mx31 b/doc/README.mx31 > deleted file mode 100644 > index 291c2f3..0000000 > --- a/doc/README.mx31 > +++ /dev/null > @@ -1,17 +0,0 @@ > -U-Boot for Freescale i.MX31 > - > -This file contains information for the port of U-Boot to the Freescale > -i.MX31 SoC. > - > -1. CONFIGURATION OPTIONS/SETTINGS > ---------------------------------- > - > -1.1 Configuration of MC13783 SPI bus > ------------------------------------- > -The power management companion chip MC13783 is connected to the > -i.MX31 via an SPI bus. Use the following configuration options > -to setup the bus and chip select used for a particular board. > - > -CONFIG_MC13783_SPI_BUS -- defines the SPI bus the MC13783 is connected > to. > - Note that 0 is CSPI1, 1 is CSPI2 and 2 is CSPI3. > -CONFIG_MC13783_SPI_CS -- define the chip select the MC13783 s > connected to.
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
