So the bug here is about renaming interfaces on boot and this seems to be resolved by the new upload. Does this regress previous behavior? Did renaming interfaces on a running system work in the previous version and this upload introduces a regression? If not, we should fill in a separate bug and try getting it fixed with the next upload.
Will be waiting with releasing this package until it's clear what's the situation here. -- You received this bug notification because you are a member of Ubuntu Touch seeded packages, which is subscribed to systemd in Ubuntu. https://bugs.launchpad.net/bugs/1770082 Title: systemd-networkd not renaming devices on boot Status in netplan: Fix Released Status in cloud-init package in Ubuntu: Confirmed Status in netplan.io package in Ubuntu: Fix Released Status in nplan package in Ubuntu: Fix Released Status in systemd package in Ubuntu: Confirmed Status in nplan source package in Xenial: Fix Released Status in netplan.io source package in Bionic: Fix Committed Bug description: [Impact] Systems relying on renaming network interfaces at boot and when 'netplan apply' is run. [Test case] - Write a new netplan YAML (adjusting for current system as necessary): network: version: 2 ethernets: ens3: dhcp4: true match: macaddress: 52:54:00:de:bd:f6 set-name: myif0 - Run 'netplan apply' - Verify that the device is correctly renamed to 'myif0'. - Reboot. - Make sure the device is correctly renamed to 'myif0'. [Regression potential] Changes in rename logic to add udev rules may otherwise impact applying different settings to the network interfaces. Changes in settings on network interfaces, missing parameters (especially on bonds, bridges) should be investigated as potential regressions. Other failures to apply network settings might also happen if there's a race between applying renames via the udev rules, and using the new names to apply configuration changes to the interfaces. === systemd issue === Renaming devices doesn't seem to work. If I disable all other network configuration and create /etc/systemd/network/10-network.link with: [Match] MACAddress=52:54:00:c1:c9:bb [Link] Name=myiface3 I expect this to cause the device with that MAC address to be renamed to myiface3. However, when I reboot, I instead see: $ ip l 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: ens3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 52:54:00:c1:c9:bb brd ff:ff:ff:ff:ff:ff The device is not renamed. This link file is pretty much identical to Example 2 in https://www.freedesktop.org/software/systemd/man/systemd.link.html. The renaming does work if I boot with net.ifnames=0, and oddly, it also works if I unbind the device and rebind it as netplan apply does. No setting of NamePolicy seems to help. === Original Bug == 'set-name:' doesn't change the name of a network interface on boot, it only works when you do netplan apply. Say I take this 50-cloud-init.yaml file: # This file is generated from information provided by # the datasource. Changes to it will not persist across an instance. # To disable cloud-init's network configuration capabilities, write a file # /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following: # network: {config: disabled} network: version: 2 ethernets: ens3: dhcp4: true match: macaddress: 52:54:00:de:bd:f6 set-name: ens3 Say I change set-name to 'myiface3' and reboot. I expect that the device will be called myiface3 and brought up fine with dhcp. However, instead I see: $ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: ens3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 52:54:00:de:bd:f6 brd ff:ff:ff:ff:ff:ff The name has not been changed, and the device has not been brought up. If I run netplan apply however, I see the following: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 3: myiface3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000 link/ether 52:54:00:de:bd:f6 brd ff:ff:ff:ff:ff:ff inet 192.168.122.151/24 brd 192.168.122.255 scope global dynamic myiface3 valid_lft 3575sec preferred_lft 3575sec inet6 fe80::5054:ff:fede:bdf6/64 scope link valid_lft forever preferred_lft forever So names are successfully changed with netplan apply. This seems to be some udev-related timing or priority issue that I'm still trying to hunt down. This breaks some forms of migration in certain cloud environments. To manage notifications about this bug go to: https://bugs.launchpad.net/netplan/+bug/1770082/+subscriptions -- Mailing list: https://launchpad.net/~touch-packages Post to : touch-packages@lists.launchpad.net Unsubscribe : https://launchpad.net/~touch-packages More help : https://help.launchpad.net/ListHelp
