Partially working here on fully updated Ubuntu 18.04 Server on
VirtualBox :(
I've enabled -proposed repo and updated both nplan/bionic-proposed and
netplan.ion/bionic-proposed packages.
Now interfaces got renamed, but IPs are not assigned at boot (both DHCP and
static ones).
Calling "netplan generate && netplan apply" after boot only sets the static IPs
while DHCP still remains unset.
# dpkg -s netplan.io
Package: netplan.io
Status: install ok installed
Priority: important
Section: net
Architecture: amd64
Version: 0.36.3
# cat /etc/netplan/01-netcfg.yaml
network:
version: 2
renderer: networkd
ethernets:
id0:
match:
macaddress: 08:00:27:6b:d8:91
set-name: eth_static
addresses: [ 1.2.3.4/16 ]
gateway4: 5.6.7.8
id1:
match:
macaddress: 08:00:27:23:68:f5
set-name: eth_dhcp
dhcp4: true
*** (just after boot) ***
# ifconfig -a
eth_dhcp: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 08:00:27:23:68:f5 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth_static: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 08:00:27:6b:d8:91 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 2 bytes 78 (78.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 2 bytes 78 (78.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
*** (after "netplan apply") ***
eth_dhcp: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 08:00:27:23:68:f5 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eth_static: flags=4098<BROADCAST,MULTICAST> mtu 1500
inet 1.2.3.4 netmask 255.255.0.0 broadcast 1.2.255.255
inet6 fe80::a00:27ff:fe6b:d891 prefixlen 64 scopeid 0x20<link>
ether 08:00:27:6b:d8:91 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 2 bytes 78 (78.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 2 bytes 78 (78.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
** Tags removed: verification-needed-bionic
** Tags added: verification-failed-bionic
** Tags removed: verification-needed
--
You received this bug notification because you are a member of Ubuntu
Touch seeded packages, which is subscribed to systemd in Ubuntu.
https://bugs.launchpad.net/bugs/1770082
Title:
systemd-networkd not renaming devices on boot
Status in netplan:
Confirmed
Status in cloud-init package in Ubuntu:
Confirmed
Status in netplan.io package in Ubuntu:
Fix Released
Status in nplan package in Ubuntu:
Fix Released
Status in systemd package in Ubuntu:
Confirmed
Status in nplan source package in Xenial:
Fix Committed
Status in netplan.io source package in Bionic:
Fix Committed
Bug description:
[Impact]
Systems relying on renaming network interfaces at boot and when 'netplan
apply' is run.
[Test case]
- Write a new netplan YAML (adjusting for current system as necessary):
network:
version: 2
ethernets:
ens3:
dhcp4: true
match:
macaddress: 52:54:00:de:bd:f6
set-name: myif0
- Run 'netplan apply'
- Verify that the device is correctly renamed to 'myif0'.
- Reboot.
- Make sure the device is correctly renamed to 'myif0'.
[Regression potential]
Changes in rename logic to add udev rules may otherwise impact applying
different settings to the network interfaces. Changes in settings on network
interfaces, missing parameters (especially on bonds, bridges) should be
investigated as potential regressions. Other failures to apply network settings
might also happen if there's a race between applying renames via the udev
rules, and using the new names to apply configuration changes to the interfaces.
=== systemd issue ===
Renaming devices doesn't seem to work.
If I disable all other network configuration and create
/etc/systemd/network/10-network.link with:
[Match]
MACAddress=52:54:00:c1:c9:bb
[Link]
Name=myiface3
I expect this to cause the device with that MAC address to be renamed
to myiface3. However, when I reboot, I instead see:
$ ip l
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: ens3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT
group default qlen 1000
link/ether 52:54:00:c1:c9:bb brd ff:ff:ff:ff:ff:ff
The device is not renamed.
This link file is pretty much identical to Example 2 in
https://www.freedesktop.org/software/systemd/man/systemd.link.html.
The renaming does work if I boot with net.ifnames=0, and oddly, it
also works if I unbind the device and rebind it as netplan apply does.
No setting of NamePolicy seems to help.
=== Original Bug ==
'set-name:' doesn't change the name of a network interface on boot, it
only works when you do netplan apply.
Say I take this 50-cloud-init.yaml file:
# This file is generated from information provided by
# the datasource. Changes to it will not persist across an instance.
# To disable cloud-init's network configuration capabilities, write a file
# /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following:
# network: {config: disabled}
network:
version: 2
ethernets:
ens3:
dhcp4: true
match:
macaddress: 52:54:00:de:bd:f6
set-name: ens3
Say I change set-name to 'myiface3' and reboot. I expect that the
device will be called myiface3 and brought up fine with dhcp. However,
instead I see:
$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: ens3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
qlen 1000
link/ether 52:54:00:de:bd:f6 brd ff:ff:ff:ff:ff:ff
The name has not been changed, and the device has not been brought up.
If I run netplan apply however, I see the following:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
3: myiface3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state
UP group default qlen 1000
link/ether 52:54:00:de:bd:f6 brd ff:ff:ff:ff:ff:ff
inet 192.168.122.151/24 brd 192.168.122.255 scope global dynamic myiface3
valid_lft 3575sec preferred_lft 3575sec
inet6 fe80::5054:ff:fede:bdf6/64 scope link
valid_lft forever preferred_lft forever
So names are successfully changed with netplan apply.
This seems to be some udev-related timing or priority issue that I'm
still trying to hunt down.
This breaks some forms of migration in certain cloud environments.
To manage notifications about this bug go to:
https://bugs.launchpad.net/netplan/+bug/1770082/+subscriptions
--
Mailing list: https://launchpad.net/~touch-packages
Post to : touch-packages@lists.launchpad.net
Unsubscribe : https://launchpad.net/~touch-packages
More help : https://help.launchpad.net/ListHelp
