On Fri, May 25, 2018 at 9:09 AM, Mathieu Trudel-Lapierre <mathieu...@gmail.com> wrote: > I'm not completely sure where the code lives in cloud-init; it looks a > bit like what's in: > > cloudinit/net/netplan.py > > But the code does read as though it should not be running 'udevadm test- > builtin net_setup_link'. However, deploying a system with MAAS shows a > /etc/cloud/cloud.cfg.d/50-curtin-networking.cfg file, which contains > data referring to the network interfaces: > > network: > config: > - id: ens6 > mac_address: 52:54:00:31:27:2c > mtu: 1500 > name: ens6 > subnets: > - address: 10.3.99.13/24 > gateway: 10.3.99.1 > type: static > type: physical > version: 1 > > With that file in place, any netplan config renaming the interface to > something other than ens6 will see the interface being renamed *again* > back to ens6, when that file is removed, this behavior does not appear.
Cloud-init only renders network config once per-instance. If a user wanted to modify this to something else (and we fix udev to handle .link file name changes) then there won't be any additional renames. Even without the change, cloud-init isn't going to call udevadm test-builtin more than once per-instance. > > -- > You received this bug notification because you are subscribed to > netplan. > Matching subscriptions: netplan > https://bugs.launchpad.net/bugs/1770082 > > Title: > systemd-networkd not renaming devices on boot > > To manage notifications about this bug go to: > https://bugs.launchpad.net/netplan/+bug/1770082/+subscriptions -- You received this bug notification because you are a member of Ubuntu Touch seeded packages, which is subscribed to systemd in Ubuntu. https://bugs.launchpad.net/bugs/1770082 Title: systemd-networkd not renaming devices on boot Status in netplan: Confirmed Status in cloud-init package in Ubuntu: Confirmed Status in systemd package in Ubuntu: Confirmed Bug description: === systemd issue === Renaming devices doesn't seem to work. If I disable all other network configuration and create /etc/systemd/network/10-network.link with: [Match] MACAddress=52:54:00:c1:c9:bb [Link] Name=myiface3 I expect this to cause the device with that MAC address to be renamed to myiface3. However, when I reboot, I instead see: $ ip l 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: ens3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 52:54:00:c1:c9:bb brd ff:ff:ff:ff:ff:ff The device is not renamed. This link file is pretty much identical to Example 2 in https://www.freedesktop.org/software/systemd/man/systemd.link.html. The renaming does work if I boot with net.ifnames=0, and oddly, it also works if I unbind the device and rebind it as netplan apply does. No setting of NamePolicy seems to help. === Original Bug == 'set-name:' doesn't change the name of a network interface on boot, it only works when you do netplan apply. Say I take this 50-cloud-init.yaml file: # This file is generated from information provided by # the datasource. Changes to it will not persist across an instance. # To disable cloud-init's network configuration capabilities, write a file # /etc/cloud/cloud.cfg.d/99-disable-network-config.cfg with the following: # network: {config: disabled} network: version: 2 ethernets: ens3: dhcp4: true match: macaddress: 52:54:00:de:bd:f6 set-name: ens3 Say I change set-name to 'myiface3' and reboot. I expect that the device will be called myiface3 and brought up fine with dhcp. However, instead I see: $ ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: ens3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 52:54:00:de:bd:f6 brd ff:ff:ff:ff:ff:ff The name has not been changed, and the device has not been brought up. If I run netplan apply however, I see the following: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 3: myiface3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000 link/ether 52:54:00:de:bd:f6 brd ff:ff:ff:ff:ff:ff inet 192.168.122.151/24 brd 192.168.122.255 scope global dynamic myiface3 valid_lft 3575sec preferred_lft 3575sec inet6 fe80::5054:ff:fede:bdf6/64 scope link valid_lft forever preferred_lft forever So names are successfully changed with netplan apply. This seems to be some udev-related timing or priority issue that I'm still trying to hunt down. This breaks some forms of migration in certain cloud environments. To manage notifications about this bug go to: https://bugs.launchpad.net/netplan/+bug/1770082/+subscriptions -- Mailing list: https://launchpad.net/~touch-packages Post to : touch-packages@lists.launchpad.net Unsubscribe : https://launchpad.net/~touch-packages More help : https://help.launchpad.net/ListHelp
