Rein,
I have successfully compiled this version (1.0.0) on Ubuntu 9.04. No
complaints from the compiler.
A couple of early observations:
- I cannot get the TLF to control the rig. rigctl from the command line
tested successfully on my radio (model 204 on Hamlib 1.2.8). Verbose
mode (tlf -v) tells me...
Welcome to tlf-0.9.31 by PA0R!!
reading country data
reading configuration data
Opening config file logcfg.dat
reading contest rules file: rules/10M_ver1
Using contest rules file: rules/10M_ver1
reading multiplier data
reading callmaster data
Cannot find initial exchange file
No initial exchange file
No Hamlib library, using native driver
Rignumber is 204
Rig speed is 57600
Keyer is cwdaemon
A: Phone message #1 is /home/rob/tlf/sounds/n6rob.ogg
I have also started with tlf -d (debug mode for rigctl) but the output
is exactly the same as tlf -v.
The rig control portion of logcfg.dat says...
# #
# RADIO CONTROL #
# (comment out if not present) #
# Rigmodel = Hamlib index, here #
# for ten tec OMNI VI #
#################################
#
RADIO_CONTROL
RIGMODEL=204
RIGSPEED=57600
RIGPORT=/dev/ttyS0
#RIGPORT=/dev/ttyUSB2
#
SSBMODE
#
#RIT_CLEAR
#
SHOW_FREQUENCY
#
I have verified using rigctl from the command line that /dev/ttyS0 is
the correct port address, and the rig is set to 57.6K.
- I can't get the voicekeyer to work, but I speculate that it may be
because the radio is not communicating effectively with tlf - but I am
not certain of this. The CW keyer plays the side tone just fine. I
haven't tested the lp0 with a voltmeter to see if it's actually keying
the rig (cwdaemon 0.9.4 had a problem with this before). But I will
test that later. I have tested the audio files using the play from the
command line with the exact same paths as I used in logcfg.dat and they
play correctly.
I have attached my logcfg.dat and rule files; but I don't know if the
list server will accept them.
I am hoping to use TLF for the ARRL 10M contest in a couple of weeks,
any guidance before then would be appreciated. As always, thank you
very much for creating tlf!
73,
Rob, N6ROB
-----Original Message-----
From: Rein Couperus <r...@couperus.com>
To: TLF-devel@nongnu.org
Subject: [Tlf-devel] Pre-release of TLF-1.0.0
Date: Fri, 04 Dec 2009 15:14:33 +0100
A prerelease of TLF-1.0.0 is available at
http://hermes.esrac.ele.tue.nl/TLF/alpha for testing.
This release should prevent segfaults on ubuntu 9.04 and 9.10.
Several bugs were fixed by NC1C and DL1JBE.
When you want to compile it on UBUNTU, you will need to install
build-essential, libncurses5-devel,
and automake 1.9, then do a ./configure, make and sudo make install.
happy testing, 73
Rein PA0R
RULES=10M_ver1
# DEC-09
#################################
# #
# TLF-LOGCFG.DAT v. 0.9.21 #
# #
# Uncomment the options you #
# want to enable. See tlf.doc #
# for a description of the #
# options. You can keep diff- #
# erent versions for different #
# contests. I keep separate #
# configuration files for #
# each contest. If you enable #
# more than 1 mutually exclu- #
# sive options, the last one #
# will be efective. #
# #
# #
#################################
#
#CTCOMPATIBLE
#
#################################
# #
# EDITOR #
# #
#################################
#
EDITOR=joe
#EDITOR=vi
#EDITOR=e3
#EDITOR=MC
#
#################################
# #
# CALL #
# #
#################################
#
CALL=N6ROB
#
#
#################################
# #
# Time offset from UTC #
# #
#################################
#
TIME_OFFSET=0
#TIME_MASTER
#
#################################
# #
# LAN PORT #
# #
#################################
# addnode only OTHER nodes !!
#
#ADDNODE=10.0.0.115
#ADDNODE=192.168.1.2
#
#THISNODE=A
#
#LAN_DEBUG
#
#################################
# #
# KEYERPORT #
# #
#################################
#
NETKEYER
NETKEYERPORT=6789
NETKEYERHOST=127.0.0.1
#
#################################
# #
# KEYERPARAMETERS #
# #
#################################
#---speed (6 ... 60 wpm)
CWSPEED=20
#---weight (-5 ... 5 ms)
WEIGHT=1
#---cq delay (s)
CQDELAY=11
#---txdelay (ms)
TXDELAY=2
#---sidetone (200...800, 0 = mute)
CWTONE=800
#SOUNDCARD
SIDETONE_VOLUME=30
#
#################################
# #
# Voice Keyer Files #
# (F1 to F12) #
#################################
#
VKM1=/home/rob/tlf/sounds/cq2.ogg
VKM2=/home/rob/tlf/sounds/n6rob.ogg
#VKM3=/home/rob/tlf/sounds/59z6.ogg
#VKM4=/home/rob/tlf/sounds/qrz.ogg
#VKM5=/home/rob/tlf/sounds/
#VKM6=/home/rob/tlf/sounds/n6rob.ogg
#VKM7=/home/rob/tlf/sounds/
#VKM8=/home/rob/tlf/sounds/
#VKM9=/home/rob/tlf/sounds/
#VKM10=/home/rob/tlf/sounds/
#VKM11=/home/rob/tlf/sounds/
#VKM12=/home/rob/tlf/sounds/cq2.ogg
#VKSPR=/home/rob/tlf/sounds/
#VKCWR=/home/rob/tlf/sounds/
#
#################################
# #
# PACKET INTERFACE #
# #
#################################
# Cluster: PI4TUE (Eindhoven)
#TELNETHOST=128.111.56.240
#TELNETHOST=131.155.192.179
#TELNETPORT=7300
#automatic login#################
#CLUSTERLOGIN=N6ROB
#write log to disk###############
#CLUSTER_LOG
#
#use tnc instead of telnet#######
#TNCPORT=/dev/ttyS0
#TNCPORT=/dev/ttyUSB1
#TNCSPEED=2400
#
#get clusterinfo from network####
#FIFO_INTERFACE
#
#################################
# #
# RADIO CONTROL #
# (comment out if not present) #
# Rigmodel = Hamlib index, here #
# for ten tec OMNI VI #
#################################
#
RADIO_CONTROL
RIGMODEL=204
RIGSPEED=57600
RIGPORT=/dev/ttyS0
#RIGPORT=/dev/ttyUSB2
#
SSBMODE
#
#RIT_CLEAR
#
SHOW_FREQUENCY
#
#################################
# #
# INFORMATION WINDOWS #
# #
#################################
#
#CLUSTER
#BANDMAP
#SPOTLIST
#FILTER
#
#SCOREWINDOW
#
#CHECKWINDOW
#################################
# #
# CHECK PARTIAL FUNCTION #
# #
#################################
#
#PARTIALS
#USEPARTIALS
#MANY_CALLS
#
#################################
# #
# CONDX (info for muf calc.) #
# #
#################################
#
SUNSPOTS=30
SFI=100
#
#################################
# #
# Misc commands #
# #
#################################
# No automatic 'qso before msg'
NOB4
#
# No automatic cq
#NOAUTOCQ
#
# Left/right arrows don't change band...
#NO_BANDSWITCH_ARROWKEYS
#
# Marker file for Xplanet
#MARKERS=tlfmarkers
SC_DEVICE= -q
#
#############END#################
########################################
# ARRL 10M contest parameters #
# N6ROB, December 2009 #
########################################
#
CONTEST=arrl_10m_contest
LOGFILE=10M_2009
CONTEST_MODE
#
##################################
# #
# Messages F1= to F12= #
# Message CW_TU_MSG= #
# Message S&P_TU_MSG= #
# #
# % = my call #
# @ = his call #
# # = serial #
# [ = RST #
# + = increase cw speed #
# - = decrease cw speed #
# (works only with parport #
# interface) #
# #
##################################
#
F1= CQ DE %
F2= @ DE %
F3= 5NN CA %
F4= TU 73
F5= @
F6= %
F7= @ SRI QSO B4 GL
F8= AGN
F9= ?
F10= QRZ?
F11= %
F12= %
#
CW_TU_MSG=TU %
S&P_TU_MSG=TU 5NN #
#
#ALT_0=
#ALT_1=
#ALT_2=
#ALT_3=
#ALT_4=
#ALT_5=
#ALT_6=
#ALT_7=
#ALT_8=
#ALT_9=
#
#SHORT_SERIAL
#LONG_SERIAL
#
#SEND_DE
#
#################################
# #
# CONTEST PARAMETERS #
# (roll your own... ) #
#################################
#
#CALLUPDATE
#
#MIXED
#
#-------------------------------
# Can exchange be recycled?
# e.g. impossible if it is a serial
# number...
#
#RECALL_MULTS
#
# format serial number: (001)
#
#SERIAL_EXCHANGE
#
#-------------------------------
# Multiplier type:
#
#WYSIWYG_MULTIBAND
# (makes its own multiplier list
# on the go...)
#
WYSIWYG_ONCE
# (same, but mults do not count
# per band..)
#
#
#MULT_LIST=arrlsections
MULT_LIST=/home/rob/tlf/contests/10M2009/rules/us_canada_states
#SERIAL_SECTIONS
#DX_&_SECTIONS
SECTION_MULT
#POWERMULT_5
#POWERMULT_2
#
#PORTABLE_MULT_2
#
#################################
# #
# POINTS LIST #
# #
#################################
#
# How may points per qso?
#
#ONE_POINT
TWO_POINTS
#THREE_POINTS
#2EU3DX_POINTS
#
#USE_COUNTRYLIST_ONLY
#COUNTRYLIST=SP_DX:SP,HA
#COUNTRY_LIST_POINTS=10
#MY_COUNTRY_POINTS=2
#MY_CONTINENT_POINTS=5
#DX_POINTS=10
#
#
####### END #####################
_______________________________________________
Tlf-devel mailing list
Tlf-devel@nongnu.org
http://lists.nongnu.org/mailman/listinfo/tlf-devel
