Am 12/10/12 05:00, schrieb Vadim Zhukov:
> 10.12.2012 1:43 пользователь "Christian Schulte" <c...@schulte.it> написал:
>>
>> Am 12/09/12 20:58, schrieb Vadim Zhukov:
>>> Hello all.
>>>
>>> This is a bit improved version of the patch showed up on tech@ in...
>>> er-r-r... don't mind. This makes my ThinkPad usable under high load
>>> for more than a year, and should not cause problems mentioned before
>>> (spinning higher and lower constantly) by using two temperature marks
>>> instead of one.
>>>
>>> I also found that disengaged mode should be enabled separately off
>>> other modes, so now Alexander Polyakov's X100e should behave correctly.
>>>
>>> Any ThinkPad users willing to test?
>>
>> Hello,
>>
>> I am using a previous version of the patch with some temperature
>> constants modified to match the temperatures my R60 produces. My R60
>> overheats (screen starts to flicker - system freezes) even when running
>> the fan in disengaged mode constantly. I bet the patch will only
>> increase the time it takes for the system to overheat. Ever run at 100%
>> load for a few hours with a disengaged fan without problems ?
>
> Well, I didn't need disengaged mode on X60 Tablet, it overhearted rarely,
> especially if you clean up fan at least once a year. And X201i with i5 runs
> fine with this patch, if you doesn't place it on the wool. Could you please
> show "dmesg" and "sysctl hw.sensors" output from your system with any
> version of the patch being applied?
>
I did not manage to solve the thermal problems I am having with the R60
in any way. Without your patch, I cannot use the machine for more than
10 minutes without overheating even when nearly idle. It also happened
when the machine was brandnew. The problem was there right from the
start. Replaced the fan two times already due to defects.
With the latest patch applied I noticed the following:
hw.sensors.acpithinkpad0.fan0=2652 RPM
hw.sensors.acpithinkpad0.raw0=128 (fan mode: disengaged), WARNING
It reads (fan mode: disengaged) although the fan isn't spinning
full-speed. It does start spinning full-speed when getting hot. So the
fan-mode string seems to not get updated correctly when switching from
disengaged mode back to auto or somethng like that.
dmesg and sysctl hw.sensors with your latest patch applied.
Script started on Mon Dec 10 05:44:39 2012
# uptime
5:44AM up 5:30, 0 users, load averages: 0.12, 0.20, 0.26
# dmesg
OpenBSD 5.2-current (GENERIC.MP) #1: Mon Dec 10 00:05:29 CET 2012
r...@r60.schulte.it:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz ("GenuineIntel" 686-class)
1.83 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,NXE,LONG,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,LAHF,PERF
real mem = 3219517440 (3070MB)
avail mem = 3155935232 (3009MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 08/28/09, BIOS32 rev. 0 @ 0xfd690,
SMBIOS rev. 2.4 @ 0xe0010 (68 entries)
bios0: vendor LENOVO version "7CETD3WW (2.23 )" date 08/28/2009
bios0: LENOVO 9461DXG
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP SSDT ECDT TCPA APIC MCFG HPET SLIC BOOT SSDT
SSDT SSDT SSDT
acpi0: wakeup devices LID_(S3) SLPB(S3) LURT(S3) DURT(S3) EXP0(S4)
EXP1(S4) EXP2(S4) EXP3(S4) PCI1(S4) USB0(S3) USB1(S3) USB2(S3) USB7(S3)
HDEF(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpiec0 at acpi0
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 166MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz ("GenuineIntel" 686-class)
1.83 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,NXE,LONG,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,LAHF,PERF
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 2, remapped to apid 1
acpimcfg0 at acpi0 addr 0xf0000000, bus 0-63
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (AGP_)
acpiprt2 at acpi0: bus 2 (EXP0)
acpiprt3 at acpi0: bus 3 (EXP1)
acpiprt4 at acpi0: bus 4 (EXP2)
acpiprt5 at acpi0: bus 12 (EXP3)
acpiprt6 at acpi0: bus 21 (PCI1)
acpicpu0 at acpi0: C3, C2, C1, PSS
acpicpu1 at acpi0: C3, C2, C1, PSS
acpipwrres0 at acpi0: PUBS
acpitz0 at acpi0: critical temperature is 127 degC
acpitz1 at acpi0: critical temperature is 100 degC
acpibtn0 at acpi0: LID_
acpibtn1 at acpi0: SLPB
acpibat0 at acpi0: BAT0 model "92P1141" serial 3397 type LION oem "SONY"
acpibat1 at acpi0: BAT1 not present
acpiac0 at acpi0: AC unit online
acpithinkpad0 at acpi0
acpidock0 at acpi0: GDCK not docked (0)
bios0: ROM list: 0xc0000/0xfe00 0xdc000/0x4000! 0xe0000/0x10000!
cpu0: Enhanced SpeedStep 1829 MHz: speeds: 1833, 1333, 1000 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82945GM Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82945GM PCIE" rev 0x03: apic 1 int 16
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility X1400" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
radeondrm0 at vga1: apic 1 int 16
drm0 at radeondrm0
azalia0 at pci0 dev 27 function 0 "Intel 82801GB HD Audio" rev 0x02: msi
azalia0: codecs: Analog Devices AD1981HD, Conexant/0x2bfa, using Analog
Devices AD1981HD
audio0 at azalia0
ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x02: apic 1 int 20
pci2 at ppb1 bus 2
bge0 at pci2 dev 0 function 0 "Broadcom BCM5751M" rev 0x21, BCM5750 C1
(0x4201): apic 1 int 16, address 00:16:d3:bb:09:4f
brgphy0 at bge0 phy 1: BCM5750 10/100/1000baseT PHY, rev. 0
ppb2 at pci0 dev 28 function 1 "Intel 82801GB PCIE" rev 0x02: apic 1 int 21
pci3 at ppb2 bus 3
wpi0 at pci3 dev 0 function 0 "Intel PRO/Wireless 3945ABG" rev 0x02:
msi, MoW2, address 00:1b:77:8e:0a:e3
ppb3 at pci0 dev 28 function 2 "Intel 82801GB PCIE" rev 0x02: apic 1 int 22
pci4 at ppb3 bus 4
ppb4 at pci0 dev 28 function 3 "Intel 82801GB PCIE" rev 0x02: apic 1 int 23
pci5 at ppb4 bus 12
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x02: apic 1 int 16
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x02: apic 1 int 17
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x02: apic 1 int 18
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x02: apic 1 int 19
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x02: apic 1 int 19
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb5 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xe2
pci6 at ppb5 bus 21
cbb0 at pci6 dev 0 function 0 "TI PCIXX12 CardBus" rev 0x00: apic 1 int 16
"TI PCIXX12 FireWire" rev 0x00 at pci6 dev 0 function 1 not configured
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 22 device 0 cacheline 0x8, lattimer 0xb0
pcmcia0 at cardslot0
ichpcib0 at pci0 dev 31 function 0 "Intel 82801GBM LPC" rev 0x02: PM
disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x02: DMA,
channel 0 configured to compatibility, channel 1 configured to
compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GMA-4082N, PX07> ATAPI
5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ahci0 at pci0 dev 31 function 2 "Intel 82801GBM AHCI" rev 0x02: msi,
AHCI 1.1
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, FUJITSU MHW2120B, 0084> SCSI3
0/direct fixed naa.500000e0409c9cc8
sd0: 114473MB, 512 bytes/sector, 234441648 sectors
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x02: apic 1
int 23
iic0 at ichiic0
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
wsmouse1 at pms0 mux 0
pms0: Synaptics touchpad, firmware 6.2
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
aps0 at isa0 port 0x1600/31
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
mtrr: Pentium Pro MTRR support
uhidev0 at uhub3 port 1 configuration 1 interface 0 "Logitech Optical
USB Mouse" rev 2.00/3.40 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse2 at ums0 mux 0
ugen0 at uhub4 port 1 "Broadcom Corp BCM2045B" rev 2.00/1.00 addr 2
ugen1 at uhub4 port 2 "STMicroelectronics Biometric Coprocessor" rev
1.00/0.01 addr 3
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd0a (077d5f2871c60214.a) swap on sd0b dump on sd0b
# sysctl hw.sensors
hw.sensors.acpitz0.temp0=68.00 degC (zone temperature)
hw.sensors.acpitz1.temp0=67.00 degC (zone temperature)
hw.sensors.acpibat0.volt0=10.80 VDC (voltage)
hw.sensors.acpibat0.volt1=11.93 VDC (current voltage)
hw.sensors.acpibat0.power0=0.00 W (rate)
hw.sensors.acpibat0.watthour0=39.31 Wh (last full capacity)
hw.sensors.acpibat0.watthour1=1.97 Wh (warning capacity)
hw.sensors.acpibat0.watthour2=0.20 Wh (low capacity)
hw.sensors.acpibat0.watthour3=37.29 Wh (remaining capacity), OK
hw.sensors.acpibat0.raw0=0 (battery idle), OK
hw.sensors.acpiac0.indicator0=On (power supply)
hw.sensors.acpithinkpad0.temp0=68.00 degC, OK
hw.sensors.acpithinkpad0.temp1=46.00 degC, OK
hw.sensors.acpithinkpad0.temp2=46.00 degC, OK
hw.sensors.acpithinkpad0.temp3=76.00 degC, WARNING
hw.sensors.acpithinkpad0.temp4=37.00 degC, OK
hw.sensors.acpithinkpad0.temp6=35.00 degC, OK
hw.sensors.acpithinkpad0.fan0=2670 RPM
hw.sensors.acpithinkpad0.raw0=128 (fan mode: disengaged), WARNING
hw.sensors.acpidock0.indicator0=Off (not docked)
hw.sensors.cpu0.temp0=67.00 degC
hw.sensors.aps0.temp0=46.00 degC
hw.sensors.aps0.temp1=46.00 degC
hw.sensors.aps0.indicator0=On (Keyboard Active)
hw.sensors.aps0.indicator1=Off (Mouse Active)
hw.sensors.aps0.indicator2=On (Lid Open)
hw.sensors.aps0.raw0=507 (X_ACCEL)
hw.sensors.aps0.raw1=511 (Y_ACCEL)
hw.sensors.aps0.raw2=507 (X_VAR)
hw.sensors.aps0.raw3=511 (Y_VAR)
# ^D
Script done on Mon Dec 10 05:44:48 2012
