Author: gbe (doc committer)
Date: Fri Nov 20 11:45:08 2020
New Revision: 367889
URL: https://svnweb.freebsd.org/changeset/base/367889
Log:
camcontrol(8): Fix some warnings spotted by mandoc
- skipping paragraph macro: Pp before Bl
Modified:
head/sbin/camcontrol/camcontrol.8
Modified: head/sbin/camcontrol/camcontrol.8
==============================================================================
--- head/sbin/camcontrol/camcontrol.8 Fri Nov 20 11:31:25 2020
(r367888)
+++ head/sbin/camcontrol/camcontrol.8 Fri Nov 20 11:45:08 2020
(r367889)
@@ -2276,7 +2276,6 @@ These zones must be written sequentially.
If they are not written sequentially, starting at the write pointer, the
command will fail.
.El
-.Pp
.Bl -tag -width 12n
.It Fl c Ar cmd
Specify the zone subcommand:
@@ -2831,7 +2830,6 @@ This will read and decode the attribute values from pa
in tape drive sa0, and will display any
.Tn SCSI
errors that result.
-.Pp
.Bd -literal -offset indent
camcontrol zone da0 -v -c rz -P summary
.Ed
@@ -2842,7 +2840,6 @@ summary of the zone parameters, and display any
or
.Tn ATA
errors that result.
-.Pp
.Bd -literal -offset indent
camcontrol zone da0 -v -c rz -o reset
.Ed
@@ -2853,7 +2850,6 @@ pointer reset from the disk da0, and display any
or
.Tn ATA
errors that result.
-.Pp
.Bd -literal -offset indent
camcontrol zone da0 -v -c rwp -l 0x2c80000
.Ed
@@ -2864,7 +2860,6 @@ that starts at LBA 0x2c80000 and display any
or
.Tn ATA
errors that result.
-.Pp
.Bd -literal -offset indent
camcontrol epc ada0 -c timer -T 60.1 -p Idle_a -e -s
.Ed
@@ -2873,7 +2868,6 @@ Set the timer for the Idle_a power condition on drive
.Pa ada0
to 60.1 seconds, enable that particular power condition, and save the timer
value and the enabled state of the power condition.
-.Pp
.Bd -literal -offset indent
camcontrol epc da4 -c goto -p Standby_z -H
.Ed
@@ -2885,7 +2879,6 @@ the drive's lowest power state) and hold in that state
explicitly released by another
.Cm goto
command.
-.Pp
.Bd -literal -offset indent
camcontrol epc da2 -c status -P
.Ed
@@ -2903,7 +2896,6 @@ to only send the
.Tn ATA
CHECK POWER MODE command, which should not trigger a change in the drive's
power state.
-.Pp
.Bd -literal -offset indent
camcontrol epc ada0 -c list
.Ed
@@ -2911,7 +2903,6 @@ camcontrol epc ada0 -c list
Display the ATA Power Conditions log (Log Address 0x08) for
drive
.Pa ada0 .
-.Pp
.Bd -literal -offset indent
camcontrol timestamp sa0 -s -f "%a, %d %b %Y %T %z" \e
-T "Wed, 26 Oct 2016 21:43:57 -0600"
_______________________________________________
svn-src-head@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/svn-src-head
To unsubscribe, send any mail to "svn-src-head-unsubscr...@freebsd.org"
