Add to smartmontools-database Seagate-ST120HM000-1G5142
--
С уважением,
Игорь.
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-4.2.0-35-lowlatency] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST120HM000-1G5142
Serial Number: Z4M00CNX
LU WWN Device Id: 5 000c50 02ff18988
Firmware Version: C675
User Capacity: 120.034.123.776 bytes [120 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Apr 24 10:29:23 2016 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 19) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -OSR-- 166 166 006 - 1
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
9 Power_On_Hours -O--CK 082 082 000 - 15935
12 Power_Cycle_Count -O--CK 100 100 020 - 373
171 Unknown_Attribute -O--CK 100 100 000 - 0
172 Unknown_Attribute -O--CK 100 100 000 - 0
181 Program_Fail_Cnt_Total -O--CK 100 100 000 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 000 - 0
194 Temperature_Celsius -O---K 020 000 000 - 20 (Min/Max 12/56)
201 Unknown_SSD_Attribute -O--CK 100 100 000 - 0
204 Soft_ECC_Correction -O--CK 100 100 000 - 0
231 Temperature_Celsius PO--C- 096 096 010 - 5
234 Unknown_Attribute -O--CK 100 100 000 - 35398
241 Total_LBAs_Written -O--CK 100 100 000 - 1536
242 Total_LBAs_Read -O--CK 100 100 000 - 940
250 Read_Error_Retry_Rate -O--CK 100 100 000 - 78
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x07 GPL,SL R/O 2 Extended self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa8 GPL VS 521 Device vendor specific log
0xa8 SL VS 255 Device vendor specific log
0xb7 GPL,SL VS 4 Device vendor specific log
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 430 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 430 [9] occurred at disk power-on lifetime: 15934 hours (663 days + 22
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:40.540 SET FEATURES [Enable
APM]
60 00 08 00 00 00 00 05 87 05 70 40 08 00:00:40.540 READ FPDMA QUEUED
60 01 b8 00 f0 00 00 09 a2 f2 b0 40 08 00:00:40.540 READ FPDMA QUEUED
60 00 08 00 e0 00 00 05 06 fd 10 40 08 00:00:40.540 READ FPDMA QUEUED
60 01 00 00 d8 00 00 0d 83 c0 00 40 08 00:00:40.540 READ FPDMA QUEUED
Error 429 [8] occurred at disk power-on lifetime: 15921 hours (663 days + 9
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 13:58:00.070 SET FEATURES [Enable
APM]
60 01 00 00 a0 00 00 0d 81 34 00 40 08 13:58:00.070 READ FPDMA QUEUED
60 00 50 00 98 00 00 03 82 71 a8 40 08 13:58:00.070 READ FPDMA QUEUED
60 01 a8 00 90 00 00 03 82 6f f8 40 08 13:58:00.070 READ FPDMA QUEUED
60 00 08 00 88 00 00 03 82 71 a0 40 08 13:58:00.070 READ FPDMA QUEUED
Error 428 [7] occurred at disk power-on lifetime: 15907 hours (662 days + 19
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:40.480 SET FEATURES [Enable
APM]
60 00 08 00 40 00 00 00 46 f9 50 40 08 00:00:40.480 READ FPDMA QUEUED
60 00 40 00 38 00 00 0c 8a 6a c0 40 08 00:00:40.480 READ FPDMA QUEUED
60 00 20 00 30 00 00 00 4c bf e0 40 08 00:00:40.480 READ FPDMA QUEUED
60 01 00 00 18 00 00 0d 83 be 00 40 08 00:00:40.480 READ FPDMA QUEUED
Error 427 [6] occurred at disk power-on lifetime: 15907 hours (662 days + 19
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 09:59:02.070 SET FEATURES [Enable
APM]
60 00 08 00 38 00 00 05 06 39 98 40 08 09:59:02.070 READ FPDMA QUEUED
60 00 38 00 18 00 00 05 06 39 d0 40 08 09:59:02.070 READ FPDMA QUEUED
60 01 00 00 10 00 00 0d 83 bb 00 40 08 09:59:02.060 READ FPDMA QUEUED
60 00 08 00 08 00 00 05 06 39 c8 40 08 09:59:02.060 READ FPDMA QUEUED
Error 426 [5] occurred at disk power-on lifetime: 15897 hours (662 days + 9
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:40.080 SET FEATURES [Enable
APM]
60 01 00 00 40 00 00 0d 81 34 00 40 08 00:00:40.080 READ FPDMA QUEUED
60 01 00 00 38 00 00 0d 81 33 00 40 08 00:00:40.080 READ FPDMA QUEUED
60 00 08 00 30 00 00 05 89 f8 60 40 08 00:00:40.080 READ FPDMA QUEUED
60 00 08 00 28 00 00 05 89 fb b8 40 08 00:00:40.080 READ FPDMA QUEUED
Error 425 [4] occurred at disk power-on lifetime: 15840 hours (660 days + 0
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:40.060 SET FEATURES [Enable
APM]
60 02 00 00 d0 00 00 0d 81 1c 00 40 08 00:00:40.060 READ FPDMA QUEUED
60 00 08 00 c0 00 00 0b 86 f9 38 40 08 00:00:40.060 READ FPDMA QUEUED
60 00 88 00 b8 00 00 0a 0c b6 f8 40 08 00:00:40.060 READ FPDMA QUEUED
60 01 b8 00 b0 00 00 09 a2 f2 b0 40 08 00:00:40.060 READ FPDMA QUEUED
Error 424 [3] occurred at disk power-on lifetime: 15751 hours (656 days + 7
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:32.380 SET FEATURES [Enable
APM]
60 00 08 00 f0 00 00 05 86 f9 f8 40 08 00:00:32.380 READ FPDMA QUEUED
60 00 38 00 e8 00 00 06 10 0c c8 40 08 00:00:32.380 READ FPDMA QUEUED
60 00 08 00 e0 00 00 00 47 35 28 40 08 00:00:32.380 READ FPDMA QUEUED
60 00 08 00 d8 00 00 05 8a 1a 28 40 08 00:00:32.380 READ FPDMA QUEUED
Error 423 [2] occurred at disk power-on lifetime: 15699 hours (654 days + 3
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:40.560 SET FEATURES [Enable
APM]
60 01 00 00 a8 00 00 0d 81 32 00 40 08 00:00:40.560 READ FPDMA QUEUED
60 01 00 00 a0 00 00 0d 81 31 00 40 08 00:00:40.560 READ FPDMA QUEUED
60 00 20 00 98 00 00 0a 5c a5 20 40 08 00:00:40.560 READ FPDMA QUEUED
60 01 00 00 90 00 00 0d 81 30 00 40 08 00:00:40.560 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 15935 -
# 2 Short offline Completed without error 00% 14064 -
# 3 Extended offline Completed without error 00% 31 -
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 2) ==
1 0x008 4 373 Lifetime Power-On Resets
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
------------------------------------------------------------------------------
Find and fix application performance issues faster with Applications Manager
Applications Manager provides deep performance insights into multiple tiers of
your business applications. It resolves application problems quickly and
reduces your MTTR. Get your free trial!
https://ad.doubleclick.net/ddm/clk/302982198;130105516;z
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
