Hello everybody,
yesterday I got a new external usb harddisk. It's a WD Elements.
Following a clipping from my kernel log:
==========================================================================
kernel: usb 6-1.1: new SuperSpeed USB device number 6 using xhci_hcd
kernel: usb 6-1.1: New USB device found, idVendor=1058, idProduct=107c
kernel: usb 6-1.1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
kernel: usb 6-1.1: Product: Elements 107C
kernel: usb 6-1.1: Manufacturer: Western Digital
kernel: usb 6-1.1: SerialNumber: ......................
kernel: usb-storage 6-1.1:1.0: USB Mass Storage device detected
kernel: scsi host6: usb-storage 6-1.1:1.0
kernel: scsi 6:0:0:0: Direct-Access WD Elements 107C 1065 PQ: 0
ANSI: 6
kernel: sd 6:0:0:0: Attached scsi generic sg3 type 0
kernel: sd 6:0:0:0: [sdc] Spinning up disk...
kernel: .........ready
kernel: sd 6:0:0:0: [sdc] 1220934400 4096-byte logical blocks: (4.88 TB/4.54
TiB)
kernel: sd 6:0:0:0: [sdc] Write Protect is off
kernel: sd 6:0:0:0: [sdc] Mode Sense: 53 00 10 08
kernel: sd 6:0:0:0: [sdc] No Caching mode page found
kernel: sd 6:0:0:0: [sdc] Assuming drive cache: write through
kernel: sd 6:0:0:0: [sdc] 1220934400 4096-byte logical blocks: (4.88 TB/4.54
TiB)
kernel: sdc: sdc1
kernel: sd 6:0:0:0: [sdc] 1220934400 4096-byte logical blocks: (4.88 TB/4.54
TiB)
kernel: sd 6:0:0:0: [sdc] Attached SCSI disk
==========================================================================
I checked the "drivedb.h 4187 2015-12-14 21:04:09Z" and it doesn't contain an entry for that
disks. Therefore you'll find attached the following files:
- the output of "smartctl -q noserial -x /dev/sdX"
- the output of "hdparm -I /dev/sdX"
If you need more information, don't hesitate to ask.
Dieter
/dev/sdc:
ATA device, with non-removable media
Model Number: WDC WD50EZRZ-32RWYB1
Serial Number: WD-WX11D35C8FZ0
Firmware Revision: 80.00A80
Transport: Serial, SATA 1.0a, SATA II Extensions, SATA Rev
2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
Used: unknown (minor revision code 0x001f)
Supported: 9 8 7 6 5
Likely used: 9
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 9767541168
Logical Sector size: 512 bytes
Physical Sector size: 4096 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 4769307 MBytes
device size with M = 1000*1000: 5000981 MBytes (5000 GB)
cache/buffer size = unknown
Nominal Media Rotation Rate: 5700
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
DMA: *mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* 64-bit World wide name
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* NCQ priority information
* unknown 76[15]
DMA Setup Auto-Activate optimization
Device-initiated interface power management
Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Write Same (AC2)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12] (vendor specific)
unknown 206[13] (vendor specific)
* DOWNLOAD MICROCODE DMA command
* WRITE BUFFER DMA command
* READ BUFFER DMA command
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
supported: enhanced erase
Logical Unit WWN Device Identifier: 50014ee2b6bbbd56
NAA : 5
IEEE OUI : 0014ee
Unique ID : 2b6bbbd56
Checksum: correct
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-4.2.0-0.bpo.1-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD50EZRZ-32RWYB1
Firmware Version: 80.00A80
User Capacity: 5.000.981.078.016 bytes [5,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5700 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Dec 19 16:40:07 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 244) Self-test routine in progress...
40% of test remaining.
Total time to complete Offline
data collection: (65340) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 652) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 253 051 - 0
3 Spin_Up_Time POS--K 200 195 021 - 8966
4 Start_Stop_Count -O--CK 100 100 000 - 22
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 100 100 000 - 8
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 22
192 Power-Off_Retract_Count -O--CK 200 200 000 - 13
193 Load_Cycle_Count -O--CK 200 200 000 - 45
194 Temperature_Celsius -O---K 108 107 000 - 44
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 40 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 1 -
# 2 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: DST executing in background (3)
Current Temperature: 44 Celsius
Power Cycle Min/Max Temperature: 23/45 Celsius
Lifetime Min/Max Temperature: 19/45 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (52)
Index Estimated Time Temperature Celsius
53 2015-12-19 08:43 30 ***********
54 2015-12-19 08:44 31 ************
55 2015-12-19 08:45 31 ************
56 2015-12-19 08:46 ? -
57 2015-12-19 08:47 32 *************
58 2015-12-19 08:48 ? -
59 2015-12-19 08:49 32 *************
60 2015-12-19 08:50 33 **************
61 2015-12-19 08:51 ? -
62 2015-12-19 08:52 35 ****************
... ..( 3 skipped). .. ****************
66 2015-12-19 08:56 35 ****************
67 2015-12-19 08:57 36 *****************
68 2015-12-19 08:58 ? -
69 2015-12-19 08:59 28 *********
70 2015-12-19 09:00 ? -
71 2015-12-19 09:01 29 **********
72 2015-12-19 09:02 ? -
73 2015-12-19 09:03 29 **********
74 2015-12-19 09:04 ? -
75 2015-12-19 09:05 29 **********
76 2015-12-19 09:06 29 **********
77 2015-12-19 09:07 29 **********
78 2015-12-19 09:08 ? -
79 2015-12-19 09:09 23 ****
80 2015-12-19 09:10 23 ****
81 2015-12-19 09:11 23 ****
82 2015-12-19 09:12 24 *****
83 2015-12-19 09:13 24 *****
84 2015-12-19 09:14 25 ******
85 2015-12-19 09:15 26 *******
... ..( 2 skipped). .. *******
88 2015-12-19 09:18 26 *******
89 2015-12-19 09:19 27 ********
... ..( 2 skipped). .. ********
92 2015-12-19 09:22 27 ********
93 2015-12-19 09:23 28 *********
94 2015-12-19 09:24 28 *********
95 2015-12-19 09:25 28 *********
96 2015-12-19 09:26 29 **********
... ..( 3 skipped). .. **********
100 2015-12-19 09:30 29 **********
101 2015-12-19 09:31 30 ***********
... ..( 2 skipped). .. ***********
104 2015-12-19 09:34 30 ***********
105 2015-12-19 09:35 31 ************
... ..( 3 skipped). .. ************
109 2015-12-19 09:39 31 ************
110 2015-12-19 09:40 32 *************
... ..( 4 skipped). .. *************
115 2015-12-19 09:45 32 *************
116 2015-12-19 09:46 33 **************
... ..( 2 skipped). .. **************
119 2015-12-19 09:49 33 **************
120 2015-12-19 09:50 34 ***************
... ..( 11 skipped). .. ***************
132 2015-12-19 10:02 34 ***************
133 2015-12-19 10:03 35 ****************
134 2015-12-19 10:04 35 ****************
135 2015-12-19 10:05 35 ****************
136 2015-12-19 10:06 ? -
137 2015-12-19 10:07 21 **
138 2015-12-19 10:08 21 **
139 2015-12-19 10:09 21 **
140 2015-12-19 10:10 ? -
141 2015-12-19 10:11 22 ***
142 2015-12-19 10:12 ? -
143 2015-12-19 10:13 23 ****
... ..( 2 skipped). .. ****
146 2015-12-19 10:16 23 ****
147 2015-12-19 10:17 24 *****
148 2015-12-19 10:18 25 ******
149 2015-12-19 10:19 25 ******
150 2015-12-19 10:20 25 ******
151 2015-12-19 10:21 26 *******
152 2015-12-19 10:22 26 *******
153 2015-12-19 10:23 26 *******
154 2015-12-19 10:24 27 ********
155 2015-12-19 10:25 27 ********
156 2015-12-19 10:26 28 *********
157 2015-12-19 10:27 28 *********
158 2015-12-19 10:28 29 **********
159 2015-12-19 10:29 29 **********
160 2015-12-19 10:30 30 ***********
161 2015-12-19 10:31 30 ***********
162 2015-12-19 10:32 31 ************
163 2015-12-19 10:33 31 ************
164 2015-12-19 10:34 32 *************
165 2015-12-19 10:35 32 *************
166 2015-12-19 10:36 32 *************
167 2015-12-19 10:37 33 **************
168 2015-12-19 10:38 33 **************
169 2015-12-19 10:39 34 ***************
... ..( 2 skipped). .. ***************
172 2015-12-19 10:42 34 ***************
173 2015-12-19 10:43 35 ****************
174 2015-12-19 10:44 35 ****************
175 2015-12-19 10:45 35 ****************
176 2015-12-19 10:46 36 *****************
... ..( 2 skipped). .. *****************
179 2015-12-19 10:49 36 *****************
180 2015-12-19 10:50 37 ******************
... ..( 2 skipped). .. ******************
183 2015-12-19 10:53 37 ******************
184 2015-12-19 10:54 38 *******************
... ..( 3 skipped). .. *******************
188 2015-12-19 10:58 38 *******************
189 2015-12-19 10:59 39 ********************
... ..( 4 skipped). .. ********************
194 2015-12-19 11:04 39 ********************
195 2015-12-19 11:05 40 *********************
... ..( 4 skipped). .. *********************
200 2015-12-19 11:10 40 *********************
201 2015-12-19 11:11 41 **********************
... ..( 8 skipped). .. **********************
210 2015-12-19 11:20 41 **********************
211 2015-12-19 11:21 42 ***********************
... ..( 9 skipped). .. ***********************
221 2015-12-19 11:31 42 ***********************
222 2015-12-19 11:32 43 ************************
... ..( 22 skipped). .. ************************
245 2015-12-19 11:55 43 ************************
246 2015-12-19 11:56 44 *************************
... ..( 89 skipped). .. *************************
336 2015-12-19 13:26 44 *************************
337 2015-12-19 13:27 45 **************************
... ..(171 skipped). .. **************************
31 2015-12-19 16:19 45 **************************
32 2015-12-19 16:20 44 *************************
... ..( 19 skipped). .. *************************
52 2015-12-19 16:40 44 *************************
SCT Error Recovery Control command not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 23270 Vendor specific
------------------------------------------------------------------------------
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
