Hi,
My new SSD (Toshiba Q Series Pro 128GB) doesn't seem to be in current
smartctl database. Please find below smartctl -q noserial -x output so it
can be added to smartmontools:
Smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.16.0-28-generic] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA THNSNJ128GCST
Firmware Version: JTRA0102
User Capacity: 128,035,676,160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Dec 17 22:18:41 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--- 100 100 050 - 0
5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0
7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0
8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0
9 Power_On_Hours -O--C- 100 100 000 - 285
10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
12 Power_Cycle_Count -O--C- 100 100 000 - 33
167 Unknown_Attribute -O---K 100 100 000 - 0
168 Unknown_Attribute -O--C- 100 100 000 - 123
169 Unknown_Attribute PO--C- 100 100 010 - 100
173 Unknown_Attribute -O--C- 198 198 000 - 0
175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0
192 Power-Off_Retract_Count -O--C- 100 100 000 - 25
194 Temperature_Celsius PO---K 072 067 020 - 28 (Min/Max
21/33)
197 Current_Pending_Sector -O--C- 100 100 000 - 0
240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 123
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 123 [122] occurred at disk power-on lifetime: 284 hours (11 days + 20
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 08 00 00 0b 75 1a 76 40 08 Error: ICRC, ABRT at LBA =
0x0b751a76 = 192223862
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
61 01 00 00 08 00 00 0b 75 1a 76 40 08 1d+01:17:15.047 WRITE FPDMA
QUEUED
61 00 20 00 00 00 00 0b 75 1a 28 40 08 1d+01:17:15.047 WRITE FPDMA
QUEUED
61 01 00 00 f0 00 00 0b 75 19 28 40 08 1d+01:17:15.047 WRITE FPDMA
QUEUED
61 00 a0 00 e8 00 00 0b 75 18 5f 40 08 1d+01:17:15.046 WRITE FPDMA
QUEUED
61 00 40 00 e0 00 00 0b 75 17 ff 40 08 1d+01:17:15.046 WRITE FPDMA
QUEUED
Error 122 [121] occurred at disk power-on lifetime: 284 hours (11 days + 20
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 58 00 00 0a ce 59 c0 40 08 Error: ICRC, ABRT at LBA =
0x0ace59c0 = 181295552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
61 00 f8 00 58 00 00 0a ce 59 c0 40 08 1d+00:51:54.640 WRITE FPDMA
QUEUED
e7 00 00 00 00 00 00 00 00 00 00 a0 08 1d+00:51:54.640 FLUSH CACHE
e7 00 00 00 00 00 00 00 00 00 00 a0 08 1d+00:51:54.639 FLUSH CACHE
61 00 fa 00 38 00 00 0a ce 58 c6 40 08 1d+00:51:54.638 WRITE FPDMA
QUEUED
61 00 18 00 30 00 00 00 24 7c 80 40 08 1d+00:51:54.638 WRITE FPDMA
QUEUED
Error 121 [120] occurred at disk power-on lifetime: 280 hours (11 days + 16
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 30 00 00 0b 01 bc 61 40 08 Error: ICRC, ABRT at LBA =
0x0b01bc61 = 184663137
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
61 01 00 00 30 00 00 0b 01 bc 61 40 08 20:52:18.268 WRITE FPDMA
QUEUED
61 00 fa 00 28 00 00 0b 01 bb 47 40 08 20:52:18.267 WRITE FPDMA
QUEUED
61 00 e4 00 20 00 00 0b 01 ba 63 40 08 20:52:18.267 WRITE FPDMA
QUEUED
61 00 e6 00 18 00 00 0b 01 b9 7d 40 08 20:52:18.266 WRITE FPDMA
QUEUED
61 00 e4 00 10 00 00 0b 01 b8 99 40 08 20:52:18.266 WRITE FPDMA
QUEUED
Error 120 [119] occurred at disk power-on lifetime: 280 hours (11 days + 16
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 08 00 00 0b 01 86 70 40 08 Error: ICRC, ABRT at LBA =
0x0b018670 = 184649328
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
61 00 f3 00 08 00 00 0b 01 86 70 40 08 20:27:04.827 WRITE FPDMA
QUEUED
61 00 f8 00 00 00 00 0b 01 85 78 40 08 20:27:04.826 WRITE FPDMA
QUEUED
61 00 e5 00 f0 00 00 0b 01 84 93 40 08 20:27:04.825 WRITE FPDMA
QUEUED
61 00 fa 00 e8 00 00 0b 01 83 99 40 08 20:27:04.825 WRITE FPDMA
QUEUED
61 00 ef 00 e0 00 00 0b 01 82 aa 40 08 20:27:04.824 WRITE FPDMA
QUEUED
Error 119 [118] occurred at disk power-on lifetime: 278 hours (11 days + 14
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 d0 00 00 0b 51 69 f8 40 08 Error: ICRC, ABRT at LBA =
0x0b5169f8 = 189884920
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
61 01 00 00 d0 00 00 0b 51 69 f8 40 08 18:56:59.498 WRITE FPDMA
QUEUED
61 01 00 00 c8 00 00 0b 51 68 f8 40 08 18:56:59.494 WRITE FPDMA
QUEUED
61 00 f6 00 c0 00 00 0b 51 68 02 40 08 18:56:59.492 WRITE FPDMA
QUEUED
61 00 ed 00 b8 00 00 0b 51 67 15 40 08 18:56:59.490 WRITE FPDMA
QUEUED
61 00 20 00 b0 00 00 0b 51 66 f5 40 08 18:56:59.489 WRITE FPDMA
QUEUED
Error 118 [117] occurred at disk power-on lifetime: 275 hours (11 days + 11
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 60 00 00 0a 32 03 41 40 08 Error: ICRC, ABRT at LBA =
0x0a320341 = 171049793
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
61 00 2e 00 60 00 00 0a 32 03 41 40 08 15:56:44.682 WRITE FPDMA
QUEUED
61 00 44 00 58 00 00 0a 32 02 fd 40 08 15:56:44.682 WRITE FPDMA
QUEUED
61 00 80 00 50 00 00 0a 32 02 7d 40 08 15:56:44.681 WRITE FPDMA
QUEUED
61 00 f5 00 48 00 00 0a 32 01 88 40 08 15:56:44.681 WRITE FPDMA
QUEUED
61 00 fc 00 40 00 00 0a 32 00 8c 40 08 15:56:44.680 WRITE FPDMA
QUEUED
Error 117 [116] occurred at disk power-on lifetime: 264 hours (11 days + 0
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 d8 00 00 00 27 5d 00 40 08 Error: ICRC, ABRT at LBA =
0x00275d00 = 2579712
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
61 00 88 00 d8 00 00 00 27 5d 00 40 08 04:36:51.424 WRITE FPDMA
QUEUED
e7 00 00 00 00 00 00 00 00 00 00 a0 08 04:36:51.424 FLUSH CACHE
e7 00 00 00 00 00 00 00 00 00 00 a0 08 04:36:51.423 FLUSH CACHE
61 00 88 00 c0 00 00 00 27 5c 00 40 08 04:36:51.422 WRITE FPDMA
QUEUED
61 00 88 00 b8 00 00 00 27 5b 00 40 08 04:36:51.422 WRITE FPDMA
QUEUED
Error 116 [115] occurred at disk power-on lifetime: 264 hours (11 days + 0
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 70 00 00 00 26 aa 00 40 08 Error: ICRC, ABRT at LBA =
0x0026aa00 = 2533888
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- ---------------
--------------------
61 00 88 00 70 00 00 00 26 aa 00 40 08 04:35:42.476 WRITE FPDMA
QUEUED
e7 00 00 00 00 00 00 00 00 00 00 a0 08 04:35:42.468 FLUSH CACHE
e7 00 00 00 00 00 00 00 00 00 00 a0 08 04:35:42.467 FLUSH CACHE
61 00 88 00 58 00 00 00 26 a9 00 40 08 04:35:42.467 WRITE FPDMA
QUEUED
61 00 88 00 50 00 00 00 26 a8 00 40 08 04:35:42.467 WRITE FPDMA
QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 248
-
# 2 Extended offline Completed without error 00% 238
-
# 3 Short offline Completed without error 00% 238
-
# 4 Extended offline Completed without error 00% 64
-
# 5 Short offline Completed without error 00% 29
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 3 (0x0003)
SCT Support Level: 0
Device State: Active (0)
Current Temperature: 28 Celsius
Power Cycle Min/Max Temperature: 27/29 Celsius
Lifetime Min/Max Temperature: 21/33 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
00 00 04 00 01 01 00 05 05 00 00 00 00 00 00 00
00 02 00 00 26 b4 0f 00 02 02 00 00 00 00 00 06
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/40 Celsius
Min/Max Temperature Limit: 0/80 Celsius
Temperature History Size (Index): 128 (32)
Index Estimated Time Temperature Celsius
33 2014-12-17 20:11 27 ********
34 2014-12-17 20:12 28 *********
35 2014-12-17 20:13 27 ********
... ..( 6 skipped). .. ********
42 2014-12-17 20:20 27 ********
43 2014-12-17 20:21 28 *********
... ..(116 skipped). .. *********
32 2014-12-17 22:18 28 *********
SCT Error Recovery Control:
Read: 600 (60.0 seconds)
Write: 600 (60.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 2) ==
1 0x008 4 33 Lifetime Power-On Resets
1 0x018 6 2230849151 Logical Sectors Written
1 0x020 6 26816962 Number of Write Commands
1 0x028 6 412592122 Logical Sectors Read
1 0x030 6 8742221 Number of Read Commands
4 ===== = = == General Errors Statistics (rev 1) ==
4 0x008 4 0 Number of Reported Uncorrectable Errors
4 0x010 4 41 Resets Between Cmd Acceptance and Completion
5 ===== = = == Temperature Statistics (rev 1) ==
5 0x008 1 28 Current Temperature
5 0x010 1 27 Average Short Term Temperature
5 0x018 1 - Average Long Term Temperature
5 0x020 1 30 Highest Temperature
5 0x028 1 22 Lowest Temperature
5 0x030 1 28 Highest Average Short Term Temperature
5 0x038 1 24 Lowest Average Short Term Temperature
5 0x040 1 - Highest Average Long Term Temperature
5 0x048 1 - Lowest Average Long Term Temperature
5 0x050 4 0 Time in Over-Temperature
5 0x058 1 40 Specified Maximum Operating Temperature
5 0x060 4 0 Time in Under-Temperature
5 0x068 1 5 Specified Minimum Operating Temperature
6 ===== = = == Transport Statistics (rev 1) ==
6 0x008 4 275 Number of Hardware Resets
6 0x018 4 123 Number of Interface CRC Errors
7 ===== = = == Solid State Device Statistics (rev 1) ==
7 0x008 1 2~ Percentage Used Endurance Indicator
|_ ~ normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 17 Command failed due to ICRC error
0x0002 4 17 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 17 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 4 30 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 29 Device-to-host register FISes sent due to a COMRESET
0x000b 4 10 CRC errors within host-to-device FIS
0x000d 4 22 Non-CRC errors within host-to-device FIS
0x000f 2 10 R_ERR response for host-to-device data FIS, CRC
0x0010 2 22 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS,
non-CRC
------------------------------------------------------------------------------
Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server
from Actuate! Instantly Supercharge Your Business Reports and Dashboards
with Interactivity, Sharing, Native Excel Exports, App Integration & more
Get technology previously reserved for billion-dollar corporations, FREE
http://pubads.g.doubleclick.net/gampad/clk?id=164703151&iu=/4140/ostg.clktrk
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
