See attachment. Looks to me like a Seagate Momentus, but doesn't quite match
the model #...
smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.0.101-0.35-default] (SUSE RPM)
Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST9500423AS
Serial Number: 5WS35MPG
LU WWN Device Id: 5 000c50 044c9db53
Firmware Version: 0002DEM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Oct 3 08:34:33 2014 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 105) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 106 099 006 - 11890640
3 Spin_Up_Time PO---- 098 097 085 - 0
4 Start_Stop_Count -O--CK 098 098 020 - 2588
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
7 Seek_Error_Rate POSR-- 084 060 030 - 246894009
9 Power_On_Hours -O--CK 079 079 000 - 18902
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 099 099 020 - 1294
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 068 068 000 - 32
188 Command_Timeout -O--CK 100 100 000 - 0
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 056 031 045 Past 44 (0 69 46 44 0)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 1239
192 Power-Off_Retract_Count -O--CK 098 098 000 - 4902
193 Load_Cycle_Count -O--CK 097 097 000 - 6917
194 Temperature_Celsius -O---K 044 069 000 - 44 (0 11 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 106 099 000 - 11890640
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
240 Head_Flying_Hours ------ 100 253 000 - 8104603306209
241 Total_LBAs_Written ------ 100 253 000 - 2840489688
242 Total_LBAs_Read ------ 100 253 000 - 381588357
254 Free_Fall_Sensor -O--CK 001 001 000 - 48
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
GP/S Log at address 0x01 has 1 sectors [Summary SMART error log]
GP/S Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 5 sectors [Ext. Comprehensive SMART error log]
GP/S Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
GP/S Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error log]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa1 has 20 sectors [Device vendor specific log]
GP Log at address 0xa2 has 2248 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 65 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP Log at address 0xab has 1 sectors [Device vendor specific log]
GP Log at address 0xae has 1 sectors [Device vendor specific log]
GP Log at address 0xb0 has 2864 sectors [Device vendor specific log]
GP Log at address 0xbd has 252 sectors [Device vendor specific log]
GP Log at address 0xbe has 65535 sectors [Device vendor specific log]
GP Log at address 0xbf has 65535 sectors [Device vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 30 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 30 [9] occurred at disk power-on lifetime: 16290 hours (678 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 08 e7 16 18 00 00 Error: UNC at LBA = 0x08e71618 =
149362200
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 08 e7 16 18 40 00 07:02:58.566 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:58.565 READ NATIVE MAX
ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 07:02:58.564 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 07:02:58.564 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:58.564 READ NATIVE MAX
ADDRESS EXT
Error 29 [8] occurred at disk power-on lifetime: 16290 hours (678 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 08 e7 16 18 00 00 Error: UNC at LBA = 0x08e71618 =
149362200
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 08 e7 16 18 40 00 07:02:55.922 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:55.922 READ NATIVE MAX
ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 07:02:55.921 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 07:02:55.921 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:55.920 READ NATIVE MAX
ADDRESS EXT
Error 28 [7] occurred at disk power-on lifetime: 16290 hours (678 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 08 e7 16 18 00 00 Error: UNC at LBA = 0x08e71618 =
149362200
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 08 e7 16 18 40 00 07:02:52.850 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:52.850 READ NATIVE MAX
ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 07:02:52.849 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 07:02:52.849 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:52.849 READ NATIVE MAX
ADDRESS EXT
Error 27 [6] occurred at disk power-on lifetime: 16290 hours (678 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 08 e7 16 18 00 00 Error: UNC at LBA = 0x08e71618 =
149362200
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 08 e7 16 18 40 00 07:02:49.994 READ FPDMA QUEUED
60 00 00 00 08 00 00 09 e3 10 00 40 00 07:02:49.993 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:49.993 READ NATIVE MAX
ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 07:02:49.992 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 07:02:49.992 SET FEATURES [Set
transfer mode]
Error 26 [5] occurred at disk power-on lifetime: 16290 hours (678 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 08 e7 16 18 00 00 Error: UNC at LBA = 0x08e71618 =
149362200
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 09 e3 10 00 40 00 07:02:47.350 READ FPDMA QUEUED
60 00 00 00 08 00 00 08 e7 16 18 40 00 07:02:47.349 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:47.348 READ NATIVE MAX
ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 07:02:47.348 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 07:02:47.347 SET FEATURES [Set
transfer mode]
Error 25 [4] occurred at disk power-on lifetime: 16290 hours (678 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 08 e7 16 18 00 00 Error: UNC at LBA = 0x08e71618 =
149362200
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 09 e3 10 00 40 00 07:02:44.605 READ FPDMA QUEUED
61 00 00 00 08 00 00 04 26 61 00 40 00 07:02:44.587 WRITE FPDMA QUEUED
60 00 00 00 08 00 00 08 e7 16 18 40 00 07:02:44.587 READ FPDMA QUEUED
60 00 00 00 08 00 00 1a 0a 6b 10 40 00 07:02:44.586 READ FPDMA QUEUED
60 00 00 00 08 00 00 03 c5 56 60 40 00 07:02:44.578 READ FPDMA QUEUED
Error 24 [3] occurred at disk power-on lifetime: 16290 hours (678 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 08 e7 16 18 00 00 Error: UNC at LBA = 0x08e71618 =
149362200
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 08 e7 16 18 40 00 07:02:41.903 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:41.903 READ NATIVE MAX
ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 00 07:02:41.902 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 07:02:41.902 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 07:02:41.864 READ NATIVE MAX
ADDRESS EXT
Error 23 [2] occurred at disk power-on lifetime: 16290 hours (678 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 08 e7 16 18 00 00 Error: WP at LBA = 0x08e71618 =
149362200
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 28 00 00 05 1d 27 00 40 00 07:02:38.991 WRITE FPDMA QUEUED
60 00 00 00 08 00 00 08 e7 16 18 40 00 07:02:38.990 READ FPDMA QUEUED
61 00 00 00 08 00 00 1a 05 b3 18 40 00 07:02:38.990 WRITE FPDMA QUEUED
61 00 00 00 08 00 00 04 28 b5 68 40 00 07:02:38.990 WRITE FPDMA QUEUED
ef 00 90 00 03 00 00 00 00 00 00 a0 00 07:02:38.974 SET FEATURES
[Reserved for Serial ATA]
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 18902 -
# 2 Short offline Completed without error 00% 2 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 44 Celsius
Power Cycle Min/Max Temperature: 44/46 Celsius
Lifetime Min/Max Temperature: 0/69 Celsius
Lifetime Average Temperature: 39 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 30 minutes
Min/Max recommended Temperature: 14/55 Celsius
Min/Max Temperature Limit: 10/60 Celsius
Temperature History Size (Index): 128 (61)
Index Estimated Time Temperature Celsius
62 2014-09-30 17:00 44 *************************
63 2014-09-30 17:30 46 ***************************
64 2014-09-30 18:00 46 ***************************
65 2014-09-30 18:30 45 **************************
66 2014-09-30 19:00 46 ***************************
67 2014-09-30 19:30 47 ****************************
68 2014-09-30 20:00 48 *****************************
69 2014-09-30 20:30 47 ****************************
70 2014-09-30 21:00 47 ****************************
71 2014-09-30 21:30 48 *****************************
72 2014-09-30 22:00 49 ******************************
73 2014-09-30 22:30 47 ****************************
74 2014-09-30 23:00 46 ***************************
... ..( 2 skipped). .. ***************************
77 2014-10-01 00:30 46 ***************************
78 2014-10-01 01:00 45 **************************
79 2014-10-01 01:30 45 **************************
80 2014-10-01 02:00 44 *************************
81 2014-10-01 02:30 44 *************************
82 2014-10-01 03:00 44 *************************
83 2014-10-01 03:30 46 ***************************
84 2014-10-01 04:00 46 ***************************
85 2014-10-01 04:30 46 ***************************
86 2014-10-01 05:00 45 **************************
87 2014-10-01 05:30 46 ***************************
88 2014-10-01 06:00 47 ****************************
... ..( 4 skipped). .. ****************************
93 2014-10-01 08:30 47 ****************************
94 2014-10-01 09:00 46 ***************************
... ..( 7 skipped). .. ***************************
102 2014-10-01 13:00 46 ***************************
103 2014-10-01 13:30 ? -
104 2014-10-01 14:00 25 ******
105 2014-10-01 14:30 41 **********************
106 2014-10-01 15:00 43 ************************
107 2014-10-01 15:30 44 *************************
108 2014-10-01 16:00 46 ***************************
109 2014-10-01 16:30 48 *****************************
110 2014-10-01 17:00 48 *****************************
111 2014-10-01 17:30 50 *******************************
112 2014-10-01 18:00 50 *******************************
113 2014-10-01 18:30 49 ******************************
114 2014-10-01 19:00 48 *****************************
... ..( 4 skipped). .. *****************************
119 2014-10-01 21:30 48 *****************************
120 2014-10-01 22:00 ? -
121 2014-10-01 22:30 23 ****
122 2014-10-01 23:00 39 ********************
123 2014-10-01 23:30 41 **********************
124 2014-10-02 00:00 42 ***********************
125 2014-10-02 00:30 40 *********************
126 2014-10-02 01:00 39 ********************
... ..( 13 skipped). .. ********************
12 2014-10-02 08:00 39 ********************
13 2014-10-02 08:30 38 *******************
14 2014-10-02 09:00 40 *********************
15 2014-10-02 09:30 43 ************************
16 2014-10-02 10:00 43 ************************
17 2014-10-02 10:30 44 *************************
18 2014-10-02 11:00 44 *************************
19 2014-10-02 11:30 45 **************************
20 2014-10-02 12:00 44 *************************
21 2014-10-02 12:30 45 **************************
22 2014-10-02 13:00 46 ***************************
23 2014-10-02 13:30 45 **************************
... ..( 4 skipped). .. **************************
28 2014-10-02 16:00 45 **************************
29 2014-10-02 16:30 44 *************************
30 2014-10-02 17:00 45 **************************
31 2014-10-02 17:30 46 ***************************
32 2014-10-02 18:00 47 ****************************
... ..( 2 skipped). .. ****************************
35 2014-10-02 19:30 47 ****************************
36 2014-10-02 20:00 46 ***************************
37 2014-10-02 20:30 46 ***************************
38 2014-10-02 21:00 45 **************************
39 2014-10-02 21:30 45 **************************
40 2014-10-02 22:00 46 ***************************
... ..( 14 skipped). .. ***************************
55 2014-10-03 05:30 46 ***************************
56 2014-10-03 06:00 45 **************************
57 2014-10-03 06:30 45 **************************
58 2014-10-03 07:00 45 **************************
59 2014-10-03 07:30 ? -
60 2014-10-03 08:00 46 ***************************
61 2014-10-03 08:30 44 *************************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 5 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
------------------------------------------------------------------------------
Meet PCI DSS 3.0 Compliance Requirements with EventLog Analyzer
Achieve PCI DSS 3.0 Compliant Status with Out-of-the-box PCI DSS Reports
Are you Audit-Ready for PCI DSS 3.0 Compliance? Download White paper
Comply to PCI DSS 3.0 Requirement 10 and 11.5 with EventLog Analyzer
http://pubads.g.doubleclick.net/gampad/clk?id=154622311&iu=/4140/ostg.clktrk
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
