I'v got a new External HDD: Intenso Memory Space 2.5", 500GB, USB 3.0
After a few attempts I found that it works with smartctl. It seems to
use a JMicron USB3.0 to SATA bridge (JMS539) and a toshiba sata drive,
but it does not work with TYPE "usbjmicron". It works with TYPE "sat"
instead.
I attached TXT with DMESG , LSPCI -V ( relevant parts ) and SMARTCTL
-X in case you want to add it to database
Best regards,
Adi
####################### DMESG #####################################
usb 4-1: new SuperSpeed USB device number 6 using xhci_hcd
usb 4-1: New USB device found, idVendor=152d, idProduct=0539
usb 4-1: New USB device strings: Mfr=10, Product=11, SerialNumber=3
usb 4-1: Product: External USB 3.0
usb 4-1: Manufacturer: Intenso
usb 4-1: SerialNumber: 20120822205FB
usb-storage 4-1:1.0: USB Mass Storage device detected
scsi10 : usb-storage 4-1:1.0
scsi 10:0:0:0: Direct-Access Intenso External USB 3.0 0206 PQ: 0 ANSI: 6
sd 10:0:0:0: Attached scsi generic sg3 type 0
sd 10:0:0:0: [sdc] 976773120 512-byte logical blocks: (500 GB/465 GiB)
sd 10:0:0:0: [sdc] Write Protect is off
sd 10:0:0:0: [sdc] Mode Sense: 27 00 00 00
sd 10:0:0:0: [sdc] No Caching mode page found
sd 10:0:0:0: [sdc] Assuming drive cache: write through
sd 10:0:0:0: [sdc] No Caching mode page found
sd 10:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 10:0:0:0: [sdc] No Caching mode page found
sd 10:0:0:0: [sdc] Assuming drive cache: write through
sd 10:0:0:0: [sdc] Attached SCSI disk
##################### LSUSB -V ##################################
lsusb -v
Bus 004 Device 006: ID 152d:0539 JMicron Technology Corp. / JMicron USA
Technology Corp. JMS539 SuperSpeed SATA II 3.0G Bridge
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x152d JMicron Technology Corp. / JMicron USA Technology
Corp.
idProduct 0x0539 JMS539 SuperSpeed SATA II 3.0G Bridge
bcdDevice 2.06
iManufacturer 10 Intenso
iProduct 11 External USB 3.0
iSerial 3 20120822205FB
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 44
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 42
bNumDeviceCaps 3
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000002
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 32 micro seconds
Container ID Device Capability:
bLength 20
bDescriptorType 16
bDevCapabilityType 4
bReserved 0
ContainerID {00010203-0405-0607-0800-000000000000}
Device Status: 0x0001
Self Powered
############################### SMARTCTL -X ##################################
# using TYPE "-d usbjmicron" don't work for JMS539 , but do work wit "-d sat"
smartctl -x -d sat /dev/sdc
smartctl 6.1 2013-03-16 r3800 [x86_64-linux-3.10.25-gentoo-xtc-9] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD050
Serial Number: 73B7S4BZS
LU WWN Device Id: 5 000039 4e590292e
Firmware Version: AX001A
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Mar 3 18:16:04 2014 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 122) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--K 100 100 001 - 1117
4 Start_Stop_Count -O--CK 100 100 000 - 19
5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0
7 Seek_Error_Rate PO-R-- 100 100 050 - 0
8 Seek_Time_Performance P-S--- 100 100 050 - 0
9 Power_On_Hours -O--CK 100 100 000 - 1
10 Spin_Retry_Count PO--CK 100 100 030 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 9
191 G-Sense_Error_Rate -O--CK 100 100 000 - 0
192 Power-Off_Retract_Count -O--CK 100 100 000 - 2
193 Load_Cycle_Count -O--CK 100 100 000 - 46
194 Temperature_Celsius -O---K 100 100 000 - 32 (Min/Max 20/33)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O--CK 100 100 000 - 0
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 0
220 Disk_Shift -O---- 100 100 000 - 0
222 Loaded_Hours -O--CK 100 100 000 - 0
223 Load_Retry_Count -O--CK 100 100 000 - 0
224 Load_Friction -O---K 100 100 000 - 0
226 Load-in_Time -OS--K 100 100 000 - 176
240 Head_Flying_Hours P----- 100 100 001 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 1 (0x0001)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: 31/32 Celsius
Lifetime Min/Max Temperature: 20/33 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/55 Celsius
Min/Max Temperature Limit: 5/55 Celsius
Temperature History Size (Index): 478 (71)
Index Estimated Time Temperature Celsius
72 2014-03-03 10:19 ? -
... ..(406 skipped). .. -
1 2014-03-03 17:06 ? -
2 2014-03-03 17:07 23 ****
3 2014-03-03 17:08 ? -
4 2014-03-03 17:09 21 **
5 2014-03-03 17:10 22 ***
6 2014-03-03 17:11 24 *****
7 2014-03-03 17:12 ? -
8 2014-03-03 17:13 ? -
9 2014-03-03 17:14 24 *****
10 2014-03-03 17:15 ? -
11 2014-03-03 17:16 25 ******
12 2014-03-03 17:17 ? -
13 2014-03-03 17:18 24 *****
14 2014-03-03 17:19 25 ******
15 2014-03-03 17:20 ? -
16 2014-03-03 17:21 25 ******
17 2014-03-03 17:22 26 *******
18 2014-03-03 17:23 26 *******
19 2014-03-03 17:24 ? -
20 2014-03-03 17:25 25 ******
21 2014-03-03 17:26 26 *******
22 2014-03-03 17:27 26 *******
23 2014-03-03 17:28 27 ********
24 2014-03-03 17:29 ? -
25 2014-03-03 17:30 29 **********
26 2014-03-03 17:31 29 **********
27 2014-03-03 17:32 29 **********
28 2014-03-03 17:33 30 ***********
29 2014-03-03 17:34 30 ***********
30 2014-03-03 17:35 30 ***********
31 2014-03-03 17:36 31 ************
... ..( 2 skipped). .. ************
34 2014-03-03 17:39 31 ************
35 2014-03-03 17:40 32 *************
... ..( 2 skipped). .. *************
38 2014-03-03 17:43 32 *************
39 2014-03-03 17:44 ? -
40 2014-03-03 17:45 32 *************
41 2014-03-03 17:46 32 *************
42 2014-03-03 17:47 32 *************
43 2014-03-03 17:48 ? -
44 2014-03-03 17:49 32 *************
45 2014-03-03 17:50 32 *************
46 2014-03-03 17:51 32 *************
47 2014-03-03 17:52 ? -
48 2014-03-03 17:53 33 **************
49 2014-03-03 17:54 32 *************
50 2014-03-03 17:55 32 *************
51 2014-03-03 17:56 32 *************
52 2014-03-03 17:57 ? -
53 2014-03-03 17:58 33 **************
54 2014-03-03 17:59 32 *************
55 2014-03-03 18:00 32 *************
56 2014-03-03 18:01 32 *************
57 2014-03-03 18:02 ? -
58 2014-03-03 18:03 33 **************
59 2014-03-03 18:04 ? -
60 2014-03-03 18:05 31 ************
61 2014-03-03 18:06 31 ************
62 2014-03-03 18:07 31 ************
63 2014-03-03 18:08 ? -
64 2014-03-03 18:09 31 ************
... ..( 3 skipped). .. ************
68 2014-03-03 18:13 31 ************
69 2014-03-03 18:14 32 *************
70 2014-03-03 18:15 32 *************
71 2014-03-03 18:16 ? -
SMART WRITE LOG does not return COUNT and LBA_LOW register
SCT (Get) Error Recovery Control command failed
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 2) ==
1 0x008 4 9 Lifetime Power-On Resets
1 0x010 4 1 Power-on Hours
1 0x018 6 2911490 Logical Sectors Written
1 0x020 6 20218 Number of Write Commands
1 0x028 6 4839655 Logical Sectors Read
1 0x030 6 117887 Number of Read Commands
2 ===== = = == Free-Fall Statistics (rev 1) ==
2 0x010 4 0 Overlimit Shock Events
3 ===== = = == Rotating Media Statistics (rev 1) ==
3 0x008 4 0 Spindle Motor Power-on Hours
3 0x010 4 0 Head Flying Hours
3 0x018 4 47 Head Load Events
3 0x020 4 0 Number of Reallocated Logical Sectors
3 0x028 4 0 Read Recovery Attempts
3 0x030 4 0 Number of Mechanical Start Failures
4 ===== = = == General Errors Statistics (rev 1) ==
4 0x008 4 0 Number of Reported Uncorrectable Errors
4 0x010 4 0 Resets Between Cmd Acceptance and Completion
5 ===== = = == Temperature Statistics (rev 1) ==
5 0x008 1 32 Current Temperature
5 0x010 1 -~ Average Short Term Temperature
5 0x018 1 -~ Average Long Term Temperature
5 0x020 1 33 Highest Temperature
5 0x028 1 20 Lowest Temperature
5 0x030 1 -~ Highest Average Short Term Temperature
5 0x038 1 -~ Lowest Average Short Term Temperature
5 0x040 1 -~ Highest Average Long Term Temperature
5 0x048 1 -~ Lowest Average Long Term Temperature
5 0x050 4 0 Time in Over-Temperature
5 0x058 1 55 Specified Maximum Operating Temperature
5 0x060 4 0 Time in Under-Temperature
5 0x068 1 5 Specified Minimum Operating Temperature
6 ===== = = == Transport Statistics (rev 1) ==
6 0x008 4 30 Number of Hardware Resets
6 0x018 4 0 Number of Interface CRC Errors
7 ===== = = == Solid State Device Statistics (rev 1) ==
7 0x008 1 0~ Percentage Used Endurance Indicator
|_ ~ normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 7 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 6 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
########################### THE END :) #############################
------------------------------------------------------------------------------
Subversion Kills Productivity. Get off Subversion & Make the Move to Perforce.
With Perforce, you get hassle-free workflows. Merge that actually works.
Faster operations. Version large binaries. Built-in WAN optimization and the
freedom to use Git, Perforce or both. Make the move to Perforce.
http://pubads.g.doubleclick.net/gampad/clk?id=122218951&iu=/4140/ostg.clktrk
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
