Hello,

Please find attached some info on a TOSHIBA MG03ACA100 (not yet in the database).

Could you please add this drive to the smartctl database?

Thanks,

David
~# smartctl -x /dev/sg0
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.32-26-pve] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model:     TOSHIBA MG03ACA100
Serial Number:    73SDK49ZF
LU WWN Device Id: 5 000039 4ebd024cf
Firmware Version: FL1D
User Capacity:    1.000.204.886.016 bytes [1,00 TB]
Sector Size:      512 bytes logical/physical
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Tue Dec 31 12:19:06 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                (  120) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off 
support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine 
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 166) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     PO-R--   100   100   050    -    0
  2 Throughput_Performance  --S---   100   100   000    -    0
  3 Spin_Up_Time            POS--K   100   100   001    -    4213
  4 Start_Stop_Count        -O--CK   100   100   000    -    8
  5 Reallocated_Sector_Ct   PO--CK   100   100   050    -    0
  7 Seek_Error_Rate         -O-R--   100   100   000    -    0
  8 Seek_Time_Performance   --S---   100   100   000    -    0
  9 Power_On_Hours          -O--CK   099   099   000    -    644
 10 Spin_Retry_Count        -O--CK   100   100   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    8
192 Power-Off_Retract_Count -O--CK   100   100   000    -    5
193 Load_Cycle_Count        -O--CK   100   100   000    -    11
194 Temperature_Celsius     -O---K   100   100   000    -    34 (Min/Max 19/37)
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
241 Total_LBAs_Written      -O--CK   100   100   000    -    3611322951
242 Total_LBAs_Read         -O--CK   100   100   000    -    2082116718
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
GP/S  Log at address 0x00 has    1 sectors [Log Directory]
SMART Log at address 0x01 has    1 sectors [Summary SMART error log]
SMART Log at address 0x02 has   51 sectors [Comprehensive SMART error log]
GP    Log at address 0x03 has   64 sectors [Ext. Comprehensive SMART error log]
GP/S  Log at address 0x04 has    8 sectors [Device Statistics]
SMART Log at address 0x06 has    1 sectors [SMART self-test log]
GP    Log at address 0x07 has    1 sectors [Extended self-test log]
GP    Log at address 0x08 has    2 sectors [Power Conditions]
SMART Log at address 0x09 has    1 sectors [Selective self-test log]
GP    Log at address 0x10 has    1 sectors [NCQ Command Error]
GP    Log at address 0x11 has    1 sectors [SATA Phy Event Counters]
GP/S  Log at address 0x80 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x81 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x82 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x83 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x84 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x85 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x86 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x87 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x88 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x89 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8a has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8b has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8c has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8d has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8e has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x8f has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x90 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x91 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x92 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x93 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x94 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x95 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x96 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x97 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x98 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x99 has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9a has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9b has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9c has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9d has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9e has   16 sectors [Host vendor specific log]
GP/S  Log at address 0x9f has   16 sectors [Host vendor specific log]
GP/S  Log at address 0xe0 has    1 sectors [SCT Command/Status]
GP/S  Log at address 0xe1 has    1 sectors [SCT Data Transfer]

SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  
LBA_of_first_error
# 1  Short offline       Completed without error       00%       644         -
# 2  Short offline       Completed without error       00%         3         -
# 3  Extended offline    Completed without error       00%         3         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  2
SCT Version (vendor specific):       1 (0x0001)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    34 Celsius
Power Cycle Min/Max Temperature:     31/37 Celsius
Lifetime    Min/Max Temperature:     19/37 Celsius
Under/Over Temperature Limit Count:   0/0
SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      5/55 Celsius
Min/Max Temperature Limit:            5/55 Celsius
Temperature History Size (Index):    478 (396)

Index    Estimated Time   Temperature Celsius
 397    2013-12-31 04:22    33  **************
 ...    ..( 25 skipped).    ..  **************
 423    2013-12-31 04:48    33  **************
 424    2013-12-31 04:49    34  ***************
 425    2013-12-31 04:50    33  **************
 ...    ..( 35 skipped).    ..  **************
 461    2013-12-31 05:26    33  **************
 462    2013-12-31 05:27    34  ***************
 463    2013-12-31 05:28    33  **************
 ...    ..( 57 skipped).    ..  **************
  43    2013-12-31 06:26    33  **************
  44    2013-12-31 06:27    34  ***************
  45    2013-12-31 06:28    33  **************
 ...    ..(  3 skipped).    ..  **************
  49    2013-12-31 06:32    33  **************
  50    2013-12-31 06:33    34  ***************
 ...    ..( 20 skipped).    ..  ***************
  71    2013-12-31 06:54    34  ***************
  72    2013-12-31 06:55    33  **************
  73    2013-12-31 06:56    34  ***************
 ...    ..(  6 skipped).    ..  ***************
  80    2013-12-31 07:03    34  ***************
  81    2013-12-31 07:04    33  **************
  82    2013-12-31 07:05    34  ***************
 ...    ..( 27 skipped).    ..  ***************
 110    2013-12-31 07:33    34  ***************
 111    2013-12-31 07:34    33  **************
 112    2013-12-31 07:35    34  ***************
 ...    ..( 14 skipped).    ..  ***************
 127    2013-12-31 07:50    34  ***************
 128    2013-12-31 07:51    33  **************
 ...    ..(  2 skipped).    ..  **************
 131    2013-12-31 07:54    33  **************
 132    2013-12-31 07:55    34  ***************
 133    2013-12-31 07:56    33  **************
 134    2013-12-31 07:57    33  **************
 135    2013-12-31 07:58    34  ***************
 136    2013-12-31 07:59    33  **************
 ...    ..(  3 skipped).    ..  **************
 140    2013-12-31 08:03    33  **************
 141    2013-12-31 08:04    34  ***************
 142    2013-12-31 08:05    33  **************
 ...    ..( 15 skipped).    ..  **************
 158    2013-12-31 08:21    33  **************
 159    2013-12-31 08:22    34  ***************
 160    2013-12-31 08:23    33  **************
 ...    ..( 24 skipped).    ..  **************
 185    2013-12-31 08:48    33  **************
 186    2013-12-31 08:49    34  ***************
 187    2013-12-31 08:50    33  **************
 ...    ..( 37 skipped).    ..  **************
 225    2013-12-31 09:28    33  **************
 226    2013-12-31 09:29    34  ***************
 227    2013-12-31 09:30    33  **************
 228    2013-12-31 09:31    33  **************
 229    2013-12-31 09:32    33  **************
 230    2013-12-31 09:33    34  ***************
 231    2013-12-31 09:34    33  **************
 232    2013-12-31 09:35    34  ***************
 233    2013-12-31 09:36    33  **************
 234    2013-12-31 09:37    34  ***************
 ...    ..(  8 skipped).    ..  ***************
 243    2013-12-31 09:46    34  ***************
 244    2013-12-31 09:47    33  **************
 245    2013-12-31 09:48    34  ***************
 ...    ..( 13 skipped).    ..  ***************
 259    2013-12-31 10:02    34  ***************
 260    2013-12-31 10:03    33  **************
 261    2013-12-31 10:04    34  ***************
 ...    ..( 22 skipped).    ..  ***************
 284    2013-12-31 10:27    34  ***************
 285    2013-12-31 10:28    33  **************
 286    2013-12-31 10:29    34  ***************
 ...    ..( 12 skipped).    ..  ***************
 299    2013-12-31 10:42    34  ***************
 300    2013-12-31 10:43    33  **************
 301    2013-12-31 10:44    34  ***************
 ...    ..(  8 skipped).    ..  ***************
 310    2013-12-31 10:53    34  ***************
 311    2013-12-31 10:54    33  **************
 312    2013-12-31 10:55    34  ***************
 313    2013-12-31 10:56    34  ***************
 314    2013-12-31 10:57    33  **************
 315    2013-12-31 10:58    34  ***************
 ...    ..(  7 skipped).    ..  ***************
 323    2013-12-31 11:06    34  ***************
 324    2013-12-31 11:07    33  **************
 325    2013-12-31 11:08    34  ***************
 ...    ..( 67 skipped).    ..  ***************
 393    2013-12-31 12:16    34  ***************
 394    2013-12-31 12:17    35  ****************
 395    2013-12-31 12:18    35  ****************
 396    2013-12-31 12:19    35  ****************

Error SMART WRITE LOG does not return COUNT and LBA_LOW register
Warning: device does not support SCT (Get) Error Recovery Control command

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0008  4            0  Device-to-host non-data FIS retries
0x000a  4          200  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS

------------------------------------------------------------------------------
Rapidly troubleshoot problems before they affect your business. Most IT 
organizations don't have a clear picture of how application performance 
affects their revenue. With AppDynamics, you get 100% visibility into your 
Java,.NET, & PHP application. Start your 15-day FREE TRIAL of AppDynamics Pro!
http://pubads.g.doubleclick.net/gampad/clk?id=84349831&iu=/4140/ostg.clktrk
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database

Reply via email to