Hello,
Here's a device that is not supported yet on smartctl.
This is a multidisk device (2x128GB) to be configured with RAID0 (don't
know if this is relevant), so on the same device there's also /dev/sdb with
the exact same characteristics.
This drive can be found on Sony vaio SVS13A2X9ES for instance.
Best regards,
Pedro Oliveira
sudo smartctl -x /dev/sda
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.12.0-rc7-3.g5fe5110-desktop]
(SUSE RPM)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA THNSNF256GRHS
Serial Number: Y2FY100XYK4D
Firmware Version: FSSAN105
User Capacity: 128,035,676,160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Nov 11 01:31:31 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 241) Self-test routine in progress...
10% of test remaining.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 8) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control
supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--- 100 100 050 - 0
5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0
7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0
8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0
9 Power_On_Hours -O--C- 100 100 000 - 1768
10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
12 Power_Cycle_Count -O--C- 100 100 000 - 423
167 Unknown_Attribute -O---K 100 100 000 - 0
168 Unknown_Attribute -O--C- 100 100 000 - 0
169 Unknown_Attribute PO--C- 100 100 010 - 100
170 Unknown_Attribute PO--C- 100 100 010 - 0
173 Unknown_Attribute -O--C- 184 184 000 - 0
175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0
192 Power-Off_Retract_Count -O--C- 100 100 000 - 20
194 Temperature_Celsius -O---K 046 046 000 - 54 (Min/Max
20/54)
197 Current_Pending_Sector -O--C- 100 100 000 - 0
240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 3 (0x0003)
SCT Support Level: 0
Device State: DST executing in background (3)
Current Temperature: 54 Celsius
Power Cycle Min/Max Temperature: 23/54 Celsius
Lifetime Min/Max Temperature: 20/54 Celsius
Lifetime Average Temperature: 20 Celsius
Under/Over Temperature Limit Count: 0/691
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/40 Celsius
Min/Max Temperature Limit: 0/80 Celsius
Temperature History Size (Index): 128 (39)
Index Estimated Time Temperature Celsius
40 2013-11-10 23:24 42 ***********************
... ..( 55 skipped). .. ***********************
96 2013-11-11 00:20 42 ***********************
97 2013-11-11 00:21 43 ************************
... ..( 15 skipped). .. ************************
113 2013-11-11 00:37 43 ************************
114 2013-11-11 00:38 42 ***********************
... ..( 3 skipped). .. ***********************
118 2013-11-11 00:42 42 ***********************
119 2013-11-11 00:43 43 ************************
... ..( 13 skipped). .. ************************
5 2013-11-11 00:57 43 ************************
6 2013-11-11 00:58 42 ***********************
... ..( 14 skipped). .. ***********************
21 2013-11-11 01:13 42 ***********************
22 2013-11-11 01:14 41 **********************
... ..( 14 skipped). .. **********************
37 2013-11-11 01:29 41 **********************
38 2013-11-11 01:30 47 ****************************
39 2013-11-11 01:31 53 **********************************
SCT Error Recovery Control:
Read: 80 (8.0 seconds)
Write: 80 (8.0 seconds)
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 4 4 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 4 Device-to-host register FISes sent due to a COMRESET
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS,
non-CRC
sudo smartctl -x /dev/sdb
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.12.0-rc7-3.g5fe5110-desktop]
(SUSE RPM)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA THNSNF256GRHS
Serial Number: Y2FY100YYK3K
Firmware Version: FSSAN105
User Capacity: 128,035,676,160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Nov 11 01:41:45 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 8) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control
supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Spin_Up_Time POS--- 100 100 050 - 0
5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0
7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0
8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0
9 Power_On_Hours -O--C- 100 100 000 - 1768
10 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
12 Power_Cycle_Count -O--C- 100 100 000 - 423
167 Unknown_Attribute -O---K 100 100 000 - 0
168 Unknown_Attribute -O--C- 100 100 000 - 0
169 Unknown_Attribute PO--C- 100 100 010 - 100
170 Unknown_Attribute PO--C- 100 100 010 - 0
173 Unknown_Attribute -O--C- 187 187 000 - 0
175 Program_Fail_Count_Chip PO--C- 100 100 010 - 0
192 Power-Off_Retract_Count -O--C- 100 100 000 - 20
194 Temperature_Celsius -O---K 057 045 000 - 43 (Min/Max
20/55)
197 Current_Pending_Sector -O--C- 100 100 000 - 0
240 Unknown_SSD_Attribute PO--C- 100 100 050 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00%
1768 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 3 (0x0003)
SCT Support Level: 0
Device State: Active (0)
Current Temperature: 43 Celsius
Power Cycle Min/Max Temperature: 23/54 Celsius
Lifetime Min/Max Temperature: 20/55 Celsius
Lifetime Average Temperature: 20 Celsius
Under/Over Temperature Limit Count: 0/710
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 5/40 Celsius
Min/Max Temperature Limit: 0/80 Celsius
Temperature History Size (Index): 128 (46)
Index Estimated Time Temperature Celsius
47 2013-11-10 23:34 42 ***********************
... ..( 14 skipped). .. ***********************
62 2013-11-10 23:49 42 ***********************
63 2013-11-10 23:50 43 ************************
... ..( 6 skipped). .. ************************
70 2013-11-10 23:57 43 ************************
71 2013-11-10 23:58 42 ***********************
72 2013-11-10 23:59 43 ************************
73 2013-11-11 00:00 43 ************************
74 2013-11-11 00:01 42 ***********************
... ..( 13 skipped). .. ***********************
88 2013-11-11 00:15 42 ***********************
89 2013-11-11 00:16 43 ************************
... ..( 23 skipped). .. ************************
113 2013-11-11 00:40 43 ************************
114 2013-11-11 00:41 42 ***********************
115 2013-11-11 00:42 43 ************************
... ..( 16 skipped). .. ************************
4 2013-11-11 00:59 43 ************************
5 2013-11-11 01:00 42 ***********************
... ..( 14 skipped). .. ***********************
20 2013-11-11 01:15 42 ***********************
21 2013-11-11 01:16 41 **********************
... ..( 12 skipped). .. **********************
34 2013-11-11 01:29 41 **********************
35 2013-11-11 01:30 48 *****************************
36 2013-11-11 01:31 54 ***********************************
37 2013-11-11 01:32 50 *******************************
38 2013-11-11 01:33 47 ****************************
39 2013-11-11 01:34 45 **************************
40 2013-11-11 01:35 44 *************************
41 2013-11-11 01:36 43 ************************
... ..( 4 skipped). .. ************************
46 2013-11-11 01:41 43 ************************
SCT Error Recovery Control:
Read: 80 (8.0 seconds)
Write: 80 (8.0 seconds)
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 5 Device-to-host register FISes sent due to a COMRESET
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS,
non-CRC
------------------------------------------------------------------------------
November Webinars for C, C++, Fortran Developers
Accelerate application performance with scalable programming models. Explore
techniques for threading, error checking, porting, and tuning. Get the most
from the latest Intel processors and coprocessors. See abstracts and register
http://pubads.g.doubleclick.net/gampad/clk?id=60136231&iu=/4140/ostg.clktrk
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
